2001 crown vic egr to exhaust tube

You search PDF repair manual about 2001 crown vic egr to exhaust tube, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2001 crown vic egr to exhaust tube Direct Download speed 5432 Kb/s

  2001 crown vic egr to exhaust tube Full Version speed 8172 Kb/s



1997 Ford Explorer/ Mountaineer Intake Manifold Upper Repair Manual

0

Filed Under (Ford Manuals) by admin on 09-05-2012

download
Intake Manifold — Upper 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold. 15. Raise and support the vehicle; refer to Section 100-02 . 16. Access the LH exhaust manifold through the wheel well and disconnect the EGR inlet tube from the exhaust manifold (9430). 17. Lower the vehicle. 18. Disconnect the EGR inlet tube from the EGR valve and remove the EGR inlet tube. 19. Remove the EGR valve bolts and the EGR valve and gasket. 20. Remove the oil level indicator tube bracket nut and remove the oil level indicator tube (6754). 21. Remove the EGR outlet tube bracket stud bolt and remove the EGR outlet tube from the upper intake manifold. 22. Disconnect the accelerator cable assembly from the upper intake manifold bracket. 23. Remove the upper intake manifold nuts and remove the upper intake manifold and gasket. Installation 1. NOTE: Before installing the upper intake manifold, the EGR port must be clean and free of obstruction. Use combustion chamber cleaner and a suitable wire brush to remove carbon buildup from the EGR passages. Clean and inspect all surfaces. Install new seals and new gaskets. Use Metal Surface Cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the upper and lower intake manifold gasket surfaces. Position the upper intake manifold gasket on the fuel injection supply manifold. 2. Position the upper intake manifold and install the six nuts.

Related Content:

2000 mpv egr vacuum line, 1997 FORD EXPLORER VACUUM T SHAPPED HOSE, 2az fe intake manifold, 305 egr intke gasket, bad egr valve symptoms aveo chevrolet

Ford F-Series Column Shift Repairs Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
It’s a simple system. To remove the assembly, start by removing the column shift lever. This is super easy; just use two small punches to depress the two spring-loaded pivot pins on the lever, then pull the lever out. Be aware: the pivot pins and spring will shoot out. Next go under the hood, and undo the two bolts holding the clamp piece just above the steering box. The lower half of the clamp will come free. The upper half is locked to the “shoe” plate under it, and to the steering column, with a round peg cast into it. So you need to pry the shoe up away from the steering column to get the peg clear of the column. Once you do that, you need to pry the upper half of the clamp away from the shoe, so the peg is clear of the shoe. Once it is clear, you can slide the end piece off the shifter tube. Then slide the wave washer and 2-3 lever off. To get the 1-R lever off, you’ll need to pull a steel pin out of the shifter tube. It should just drop out. Then slide the lever, wave washer, and shoe off the tube. Push the shifter tube up to get the clearance needed for the shoe. The shifter tube is a hollow steel tube, with a hole drilled thru it near the bottom. In this hole there is a steel pin (the one just removed). The steel pin engages into slots in the 1-2 and 3-4 levers, to move them. As you can see, there isn’t a lot of wear in my shift levers’ slots. The pin shows some wear, where the tube contacts it. The pin is hardened steel and the shifter tube is mild steel, so the tube will be worse than the pin. The pins are available from Obsolete Ford Parts and others, P/N 01A-7337, only a couple of bucks. Getting the shifter tube out is pretty easy; just drop the column support (remove the bolts to instrument panel and loosen the pinch bolt) down to the floor, and you’ll be able to swing the shift tube to the side to clear the steering wheel, and pull it out. My pin wasn’t that worn, it’s the hole in the tube. The tube is hollow but actually has a steel plug inside it with a hole for the pin. It is pushed inside the tube and then peened in two places thru the outer tube (they punched the outer tube to lock the inner plug). inner plug had gotten loose inside the tube, too. If this is your situation, you could just drill and pin the plug to the outer tube, and get a good improvement. I wanted “like new”, so I took my shifter tube to my favorite machinist (Gene at Noor Mfg. in Albuquerque, a super guy). He made up a whole new lower end for the tube out of 1018 carbon steel. It’s got a spigot on the upper end that was pressed into the remaining tube, welded, then turned down. It is better than new! Look at the difference in the shape of the hole. Price for the work was very reasonable

Related Content:

how do you replace an altenator on a 2005 honda pilot youtube, FREE INSTRUCTIONS ON SHIFTER TUBE REPLACMENT 2001 FORD F 150 /COLUMN SHIFTER, removing a 2000ford f250 shift tube, 96 windstar shifter tube clamp holder, 2005 chrysler town and country evaporatordraintube, where is the orifuce tobe on 1998 chevy silverado, yhs-jomedia, p01626, kia sedona ac drain hose clogged, how to installand adjust console shift handle 1999 ford taurus

2006 Ford Five Hundred SE UPPER INTAKE MANIFOLD REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 30-11-2011

download
Removal All vehicles 1. Drain the cooling system. For additional information, refer to DRAINING . 2. Disconnect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 3. Remove the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 4. Remove the 4 transaxle roll restrictor cross brace bolts 5. Remove the bolt and the transaxle roll restrictor cross brace. 6. Disconnect the evaporative emissions (EVAP) canister purge valve tube from the upper intake manifold and detach the retainer. 7. Disconnect the positive crankcase ventilation (PCV), brake booster and vacuum harness tubes from the upper intake manifold. 8. Detach the fuel tube retainer from the upper intake manifold. 9. Disconnect the exhaust gas recirculation (EGR) system module electrical connector and vacuum tube. 10. Detach the vacuum tube from the upper intake manifold vacuum tube retainer. 11. Disconnect the EGR system module tube from the EGR system module. Early build 12. Disconnect and plug the throttle body and PCV coolant hoses. Late build 13. Disconnect and plug the 2 PCV coolant hoses. All vehicles 14. Disconnect the throttle body electrical connector. 15. If equipped, remove and discard the 4 upper-to-lower intake manifold screws. 16. Remove the 8 bolts and the upper intake manifold. * Remove and discard the gaskets. Installation All vehicles Fig. 4: Identifying Tightening Sequence Of Bolts Courtesy of FORD MOTOR CO. NOTE: Clean and inspect all sealing surfaces. Install new gaskets 1. Position the upper intake manifold and install the 8 bolts. * Tighten in the sequence shown to 10 N.m (89 lb-in). 2. Connect the throttle body electrical connector. Late build 3. Connect the 2 PCV coolant hoses. Early build 4. Connect the throttle body and PCV coolant hoses. All vehicle 5. Connect the EGR system module tube to the EGR system module. * Tighten to 40 N.m (30 lb-ft). 6. Attach the vacuum tube to the upper intake manifold vacuum tube retainer. 7. Connect the EGR system module electrical connector and vacuum tube. 8. Attach the fuel tube retainer to the upper intake manifold. 9. Connect the PCV, brake booster and vacuum harness tubes to the upper intake manifold. 10. Connect the EVAP canister purge valve tube to the upper intake manifold and attach the retainer. 11. Clean the 4 transaxle roll restrictor cross brace bolts using a wire brush and apply new threadlock to the threads. 12. Position the transaxle roll restrictor cross brace and install the 4 new bolts. * Tighten to 55 N.m (41 lb-ft). 13. Clean the transaxle roll restrictor cross brace-to-roll restrictor bolt using a wire brush and apply new threadlock to the threads. 14. Install a new transaxle roll restrictor cross brace-to-roll restrictor bolt. * Tighten to 48 N.m (35 lb-ft). 15. Install the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 16. Connect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 17. Fill and bleed the cooling system.

Related Content:

ford five hundred roll restrictor bushing diy, ford five hundred throttle body repair, fuel filler tube diagrams chevy impala 2003, pcv valve 3 0 ford aerostar where does small vacuum connection on pcv valve go

2000 Ford Crown Victoria/ Grand Marquis Intake Manifold – Gasoline Engines Removal and Installation Manual

0

Filed Under (Ford Manuals) by admin on 16-04-2012

download
Intake Manifold—Gasoline Engines Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 4. Disconnect the fuel line. For additional information, refer to Section 310-00A or Section 310-00B . 5. Remove the wiper arm and pivot shaft. For additional information, refer to Section 501-16 . 6. Remove the drive belt. For additional information, refer to Section 303-05 . 7. Raise the vehicle on a hoist. For additional information, refer to Section 100-02 . 8. Disconnect the electrical connector at the crankshaft position (CKP) sensor. * Disconnect the pin-type retainer from the A/C compressor bracket. 9. Disconnect the electrical connector from the A/C compressor. 10. Remove the oil bypass filter. 11. Disconnect the oil pressure sensor electrical connector and the power steering pressure (PSP) switch electrical connector. 12. Disconnect the exhaust gas recirculation (EGR) tube from the exhaust manifold 13. Lower the vehicle. 14. Disconnect the two differential pressure feedback EGR hoses. 15. Disconnect the RH heated oxygen sensor electrical connector. 16. Disconnect the fuel charging wiring electrical connectors from the eight ignition coils. 17. Disconnect the fuel charging wiring electrical connectors from the eight fuel injectors. 18. Disconnect the accelerator cable and the speed control actuator cable. 19. Remove the cables from the EGR tube heat shield and position out of the way. 20. Remove the bolts and the EGR tube heat shield. 21. Disconnect the evaporative emissions (EVAP) return tube, the main chassis vacuum supply line, and the EGR valve vacuum supply. 22. Disconnect the positive crankcase ventilation (PCV) tube assembly at two locations and remove. 23. Disconnect the electrical connector from the EGR vacuum regulator solenoid. 24. Disconnect the vacuum line from the EVAP canister purge valve. 25. Disconnect the generator cable and electrical connector 26. Remove the bolts and the generator mounting bracket. 27. Remove the upper radiator hose. 28. Disconnect the electrical connector from the idle air control (IAC) valve and the throttle position (TP) sensor. 29. Disconnect the heater water hose. 30. Disconnect the EGR tube from the EGR valve. 31. NOTE: The LH heated oxygen sensor and the transmission electrical connectors are attached to the wiring bracket and must be separated from the bracket. Remove the wiring bracket. * Disconnect the wiring connectors. * Separate the transmission harness from the stud. * Remove the nut and the bolt and remove the bracket.

Related Content:

2005 GMC Sierra 1500 How to Disconnect Vacuum Line, can you unplug the trorque converter on a 1999 honde ex, disconnected battery car turn over will not start 99 bmw 528i, dodge grand caravan liftgate slams shut, part ground strap crown vic 2011 3w7t, where is the vent pipe located on 2004 sierra gas fill up hose

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, how to check tranmission fluid on 2012 kia sedona, gm 4l60e band adjustment screws, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, 4r70w transmission rebuild manual download, 2004 saturn Clutch Assembly Exploded View, e4od repair manual download

2001-2008 GM 1500/2500 Series Pick-Up Edelbrock Header Installation Manual

0

Filed Under (GMC Manuals) by admin on 25-02-2012

download
INSTALLATION INSTRUCTIONS DISASSEMBLY 1. Disconnect negative battery cable. 2. Unbolt exhaust pipes from manifolds. RIGHT SIDE 1. Disconnect and remove spark plug wires. 2. Unbolt and remove dipstick tube. 3. Unbolt and remove manifold from top. 4. Install flange gasket and header from top. Install header bolts, lock washers, and thick flat washers supplied. Note: Ensure proper alignment on slotted holes of port flange and only snug bolts at this time. 5. Re-install spark plug wires. 6. Re-install dipstick tube. 7. Some models may require the aluminum heat shield under the A/C receiver dryer to be re-positioned, adjusted or bent to gain some clearance between header and heat shield. LEFT SIDE 1. Disconnect and remove spark plug wires. 2. Unbolt and remove manifold. 3. Install flange gasket and header from top. Install header bolts, lock washers, and thick flat washers supplied, ensure proper alignment and only snug bolts at this time. IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in poor performance and engine or vehicle damage.
©2007 Edelbrock Corporation Catalog #65022 & 65023 Page 2of 2 Brochure #63-0364 Rev. 8/07 – DA/mc Edelbrock Corporation, 2700 California St., Torrance, CA 90503 Tech Line: 1-800-416-8628 Office: 310-781-2222 Tech Fax: 310-972-2730 E-Mail: Edelbrock@Edelbrock.com 2. Using supplied hardware, re-attach the factory exhaust pipes to the headers and tighten bolts evenly to ensure a tight seal. ( Note: The 7/16 x 2 bolts are to be used on 4.8L, 5.3L, & some 6.0L V8s. The 7/16 x 1 ¾ are for the left side of 4.8L & 5.3L V8s, and on the 6.0L V8 that do not have OEdonut gaskets. 3. After the factory exhaust pipes have been tightened to the collector flange of the header, tighten the port flange bolts to recommended factoryspecifications. FINAL INSPECTION 1. Check all lines (hydraulic, vacuum, air conditioning and fuel) to ensure there is adequate clearance to headers. 2. Re-connect battery. 3. At this point, it is a good idea to look everything over and make sure that nothing was missed in assembly. 4. Start vehicle and bring up to normal operating temperature. Check for possible leaks. 5. Turn engine off and let cool. Tighten all bolts again. Note: Thick washers are to be used on slotted holes of port flange. 4. Re-install spark plug wires. Note: Due to production tolerance, it may be necessary to bend the motor mount heat shield for better clearance. ASSEMBLY OF EXHAUST PIPE Note: Some 2007 model year vehicles will have a donut gasket on the right side OE exhaust manifold. If your vehicle has that donut gasket, it will be re-used with your shorty headers (see below). This system comes with 2 exhaust crush rings. On 2001- 2006 4.8L & 5.3L V8s, one will be used on the left side collector. On 2001-2006 6.0L vehicles will use one on the left side and one on the right side to replace factory-installed crush rings. 1. On 4.8L, 5.3L, &6.0L V8s with donut gasket – Remove the donut gasket from right side exhaust manifold. Using a pair of pliers, remove the retaining ring from the donut gasket and place the donut gasket in flare of factory exhaust pipe.

Related Content:

schematics on bleeding the air from cooling system on 02 aurora, snug top wiring, 2001 chevy hd 2500 code p1626, bumper sealer used on a muffler, how to repair exhaust flange leaks on chevy tahoe, what is the diameter of the exhaust pipe for 2001 malibu

4.6L Mustang Bassani Mid Length Headers INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 05-12-2011

download
INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Safely raise & support vehicle to a comfortable working height. (One jack stand at each corner of vehicle.) 3. Spray attaching hardware and base of o2 sensors with WD40 or similar Lubricant. Remove 02 sensors from stock system. (Be careful not to damage or contaminate sensor). Stock gasket will be re-used upon assembly. 4. Remove both connector tubes between stock exhaust manifold and Bassani Modular X pipe. It may be necessary to loosen downstream clamps on the Bassani Modular X pipe. 5. Loosen EGR fitting on drivers side exhaust manifold. It will be necessary to remove nuts from the motor mounts at the K member to jack engine up. Motor mount heat shields have to be removed. 6. Loosen & remove both exhaust manifolds. 2 valve, stock manifold gaskets, depending on condition, may be re-used . Remove studs from both sides. Use supplied, and/or stock hardware. See note following #10. 7. Label wiring on starter and remove it. (Will be necessary for header installation) 8. You may also need to remove oil filter to ease installation and tightening on drivers’ side. 9. IMPORTANT! It will be necessary to unbolt steering shaft from rack. With a marker draw a straight line on shaft down to rack to index them both. Do not move front wheels or steering wheel. 10. It will be necessary to lift engine up enough to slide header tubes in and have access to install supplied header bolts. After loosening motor mount bolts, lifting engine (using a wooden block under oil pan) and removing motor mounts, one side at a time only, will ease installation. Removal of motor mounts is not mandatory. **Anti seize must be applied to all threads (header bolts and studs). It may be necessary to use a combination of header bolts and stock studs & nuts on certain tubes due to clearance between the tube and hardware. ie; stud nut or header bolt. The use of either is the installers preference. 11. Start on passenger side, with tube #1R. Push as far forward as possible to allow clearance for #2R. Once #2R is in position, install gaskets, and header bolts. When this is completed commence installation of #3R and #4R tubes following previous procedure. Leave bolts loose, DO NOT TIGHTEN UNTIL COLLECTOR IS INSTALLED. 12. When Collector R is ready for right side, place Bassani anti seize jet lube , on slip connectors to ease installation. When collector lines up with tab on header tube, fasten them together and tighten all header tubes. 13. When all hardware is properly tightened, lower engine, re-install motor mount hardware, starter and O2 sensors in collector. The use of Bassani anti seize Jet Lube is recommended on O2 sensor threads. Do not to contaminate O2 sensor bulb with lube. 14. Proceed to drivers’ side. Install #1L with gasket installed. Install supplied fasteners with Bassani anti seize jet lube on the threads. DO NOT TIGHTEN ALL THE WAY, leave semi loose. Install tube #3L, then #2L. You will need to experiment with pipes #2L and #3L. #2L will slip between #3L and #1L. Now install #4L, fasten and screw air fitting to tube #4L. Install Collector L . When collector tab lines up with header tab, tighten all hardware, and bolt on EGR, and any smog fittings. Lower engine and re-install motor mount hardware. Reconnect steering shaft using loctite 271 thread locker on bolt.

Related Content:

2002 chevy s10 exhaust flange seal, ebay ford 555 backhoe cheap service manual, replacing choke heater tube in 57 chevy exaust manifold

1996-2000 Chevrolet And GMC Suburban/ Pick-Up 2500/ 3500 Series TUBULAR EXHAUST SYSTEM INSTALLATION INSTRUCTION

0

Filed Under (Chevrolet Manuals) by admin on 29-12-2011

download
Disassembly – Left Side 1. Disconnect negative cable from battery. 2. Use penetrating oil on all nuts and bolts to be removed. This will prevent the possibility of broken or stripped nuts and bolts. 3. Remove air cleaner system (note position of line and hose connections). 4. Disconnect spark plug wires. 5. Disconnect temperature sensor wire. 6. Remove EGR fitting. 7. Remove bolts and exhaust manifold. Disassembly – Right Side 1. Remove air cleaner box. 2. Disconnect spark plug wires. 3. Remove dipstick and dipstick tube. 4. Remove bolts and exhaust manifold. 5. Clean exhaust flange surfaces on both cylinder heads at this time. DISASSEMBLY – CROSSOVER PIPE 1. Raise vehicle and support with jackstands. 2. Disconnect and remove 02 sensors (2), being careful not to rupture or destroy the unit. WARNING: Do not clean this unit in any cleaning solvent and do not damage wire. 3. Between left and right side of the catalytic converter is a 3-bolt flange with gasket. From the front face of flange, measure out 15″ towards front of truck and cut stock exhaust pipes. Remove exhaust pipes from vehicle. NOTE: Before cutting pipes, measure the height of the converter from the bottom of the floor board for when you install new exhaust pipes you can maintain same distance. •ASSEMBLY – LEFT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer, and thick flat washer at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install left side T.E.S. manifold from bottom side 3. Install all bolts and washers and tighten. Use thick flat washers on slotted holes. 4. Reinstall spark plugs. 5. Replace original equipment spark plug ends on cylinders #3 and #5 with 60° connectors and boots provided in kit. 6. Re-connect spark plug wires on left side. 7. Re-install temperature sensor wire to temperature sensor. ASSEMBLY – RIGHT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer and thick flat washers at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install right side T.E.S. manifold from top side. Now install dipstick tube. 3. Install remaining bolts and lock washers. 4. Align all parts and tighten all right side bolts at this time. 5. Replace original equipment spark plug ends on cylinders #4, #6 and #8 with 60° connectors and boots provided in kit. 6. Re-connect right side spark plug wires. 7. To prevent contact with the hot T.E.S. tubing, use nylon tie wrap (supplied) to secure the heater hose to the a.c. dryer. 8. Re-install air cleaner box. CROSSOVER PIPE ASSEMBLY 1. With catalytic converters in their natural position, install and bolt exhaust extension pipes to header collectors using 3/8″ – 16″ x 2 1/2″ hex bolts, 3/8″ flat washers, 3/8″ lock washers and 3/8 hex nuts. Use the 3″ donut provided in kit. 2. Check alignment of pipes to the catalytic converter, secure bolts. 3. With everything in place, tack weld exhaust pipes to catalytic assembly. 4. Unbolt whole exhaust assembly from vehicle and let it hang. Complete weld around pipes. 5. Bolt assembly back in vehicle and check for clearance. 6. Re-install 02 sensors. Use anti-seize on threads of sensor. Route wires clear of exhaust system. 7. Lower vehicle to ground

Related Content:

2005 taurus exhaust system diagram, 2 2 s10 exhaust flange bolts, diagram of an exhaust system on a 2003 gmc envoy, Diagram of a exhaust crossover pipe for a 95 Oldsmobile aurora, 04 pacifica parts diagram, pontiac sunfire gt exhaust system diagram, how tight should exhaust, gmc yukon exhaust manifold diagram, 454 exhaust donut installation, 2006 corvette mid pipe flange torque

V8 CHEVY CAMARO HEADER Y-PIPE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Chevy Manuals) by admin on 09-12-2011

download
Disconnect battery. 2. Lift or jack car to a comfortable height. 3. Using WD-40 spray all 6 collector studs and nuts, Y-pipe slip connect, all 4 cat pipe studs & nuts 4. Remove stock Y-pipe by removing the 2 bracket bolts and loosening up the slip connector clamp at rear then remove the 4 nuts holding the Y-pipe to the cat pipes. Slip Y-pipe out, and free from the car. 5. Remove all 4 of the O2 sensors (1) on driver manifold (1) on drive cat pipe (2) on passenger cat pipe. Four total. 6. Remove the 3 nuts on the driver side cat pipe and then remove the 3 nuts on the passenger cat pipe (be careful because the cats are heavy). 7. Remove all 8 spark plug wires. 8. Remove air tube on driver side manifold using a 10 mm socket. 9. Remove air tube on passenger side manifold using a 10 mm socket with universal. 10. Remove EGR tube on passenger side manifold using a 10″ extension with a 10 mm socket and universal. 11. Remove air pump on passenger side of engine and swing out of the way. 12. Remove EGR in front of manifold on top with a 10 mm socket and move to side. 13. Remove dipstick on passenger side 4. Remove all manifold bolts on passenger side and take manifold out. NOTE: Manifolds are Heavy 15. Remove all manifold bolts on driver side and take manifold out. NOTE: Manifolds are Heavy. 16. Unplug electrical hook up on EGR and move out of way. Note: Make sure plug wires are all the way on, and check after installation. Note: Save all stock gaskets, they will be used in installation. INSTALLATION OF BASSANI HEADERS 1. Use Bassani Jet lube on all threads 2. Install the 4 collector studs in headers 2 ea. On each side & snug down. 3. Use the stock exhaust gaskets and install the passenger side header from the bottom and install all of the header bolts then tighten them down after all of them are in. 4. Repeat step 3 for Drivers side. 5. Install the EGR tube on the lower passenger side of the Header. 6. Install the dipstick on Passenger side of engine and put the bolt in. 7. Install plug wires on Passenger side. 8. Install Air tube on Passenger side with supplied 5/16 Hardware. 9. Install EGR to front of motor and plug wire back in. 10. Install EGR tube on top of manifold with 10MM socket. 11. Install the air tube on Drivers side header with supplied 5/16 hardware and Stock Gasket. 12. Install Drivers side spark plug wires, make sure they are all the way on. 13. Install O2 Sensor in Drivers side header and tighten down. 14. Install new Bassani Cat pipe on Drivers side with Jet Lube and supplied 7/16-14 flange nuts and leave loose. 15. Install 2 ea. O2 Sensors in Passenger side Cat pipe

Related Content:

3406 e manual, passenger front side impala 2005

1984-1995 Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System Repair Manual

0

Filed Under (Honda Manuals) by admin on 22-04-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum. When servicing or repairing any part of the emissions system, it is absolutely essential to check for any obvious mechanical faults or failures. Remember, a trouble code only indicates which sensor or circuit is affected by the problem. Simple mechanical faults such as a vacuum leak or poor electrical connection can cause a fault code. The EGR valve is not simply open or closed but is modulated by controlling the amount of engine vacuum to the valve diaphragm, up to a maximum of 8 in. Hg of vacuum. The EGR valve has a sensor in the top of the valve that reports valve lift to the ECU (same as ECM, 1992-95). The ECU modulates the position of the control solenoid valve to control the EGR valve lift according to an internal program. Upstream of the control solenoid valve, the CVC provides a constant supply of vacuum so EGR control is precise under all manifold vacuum conditions

Related Content:

2004 honda purge control valve, c230 2005 removing pcv valve and hoses, 2008 hyundai elantra purge valve, clean egr valve lincoln, 2007 implala vent solenoid replacement, pvc valve for 2001 merc sable 24 valve overhead cam, egr valve chevy trailblaxer 2005, where is the pcv valve on chevy cruze, where is the pvc valve located on a 2008 toyota tundra, fuel purge valve for 2006 chevy impala

Related Content:

2000 mpv egr vacuum line, 1997 FORD EXPLORER VACUUM T SHAPPED HOSE, 2az fe intake manifold, 305 egr intke gasket, bad egr valve symptoms aveo chevrolet