2001 dodge caravan radiator fan relay

You search PDF repair manual about 2001 dodge caravan radiator fan relay, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2001 dodge caravan radiator fan relay Direct Download speed 5432 Kb/s

  2001 dodge caravan radiator fan relay Full Version speed 8172 Kb/s



1998 Dodge Truck Caravan Replace Radiator Fan Relay

0

Filed Under (Dodge Manuals) by admin on 16-06-2011

download
1. With the ignition key in the OFF position, disconnect the battery. 2. Remove the two (2) screws that attach the air inlet resonator to the upper radiator support. 3. Disconnect the upper and lower air inlet hoses from the resonator and remove the resonator. 4. Remove the air cleaner housing. 5. Locate the radiator cooling fan relay on the left front inner frame rail just behind the radiator (Figure 1). 6. Disconnect the radiator fan relay wiring connector. 7. Remove the radiator fan relay. Discard the relay and the attaching screws. 8. Install the new radiator fan relay using the supplied screws. Tighten the screws to 35 in-lbs (4 N.m). CAUTION: Do not over torque screws. To ensure heat transfer and proper operation, the new radiator fan relay must be installed using both of the provided screws. 9. Connect the radiator fan relay electrical connector. Slide the red latch to the locked position. 10. Install the air cleaner housing. 11. Install the resonator assembly and connect the upper and lower air inlet hoses. 12. Install the resonator to upper radiator support screws. Tighten the screws securely. 13. Connect the negative battery cable.

Related Content:

ford focus 2001 wiring harness replacement, replace 2006 ford escape radiator, 1998 pontiac montana block drains, cooling fan wiring diagram for 2004 impala with police package, dodge caravan cooling fan connector removal, how to replace 2008 escape radiator fans

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, where is the relay switch for liftgate in 2005 esclade, 99 eldorado fuel pump relay test, where is the washer relay located in a 2009 chevy impala, sensor switch on rear beam axle of 2005 saturn relay, 1993 corvette power seat and power window shorting out breaker, g5 sunroof relay

2007 TOYOTA TUNDRA SUPERCHARGER FIT KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 20-03-2012

download
1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 3, save this coolant as it will be reused. CAUTION: To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause the hot engine coolant and steam to blow out from the radiator. (h) All parts that are removed and not reused should be saved for the customer, i.e., “discard” means to save for the customer 2. Cover Removal. (a) Remove the engine V-bank cover by Lifting the front of the cover and pulling away from the firewall (Fig 2-1). Discard these parts. (b) If installed, remove the No. 1 engine under cover (Fig 2-2) by removing the 3 screws and 5 bolts. Save these parts for reuse. 3. Drain Engine Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns. (a) Loosen the radiator drain cock plug (Fig. 3-1). (b) Remove the radiator cap. Then drain the coolant from the radiator into a clean container so it can be reused (Fig. 3-1). (c) Loosen the 2 cylinder block drain cock plugs (Fig.3-1). Then drain the coolant from the engine and save for reuse. (d) Tighten the 2 cylinder block drain cock plugs. Torque: 13 Nm (10 ft lbf) 4. Fan and Shroud Removal. (a) Remove the upper radiator hose. Mark the radiator end of this hose with a marker or tape. This hose will be re-installed inverted and the mark will help identify the ends. (b) Loosen the 4 nuts holding the fluid coupling fan (Figs. 4-1). (c) Remove the fan/generator V-rib belt. Discard this belt as it will be replaced by a new belt. (d) Disconnect the reservoir hose from the upper radiator tank. (e) For vehicles with Trailer Towing System: Detach the claw to open the No. 1 hose clamp on the side of the fan shroud (Fig 4-2). (f) Remove the 2 bolts holding the fan shroud (Figs 4-3). Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan. Retain these parts for reuse. Temporarily re-install the 4 nuts to keep the pulley in place (reference Fig 4-1). Do not tighten. CAUTION: Be careful not to damage the radiator core. It is helpful to protect the radiator core with a piece of cardboard to prevent damage during subsequent steps. 5. Air Cleaner Lower Box Replacement. (a) Remove the air cleaner hose by disconnecting the vacuum and ventilation hoses and loosening the 2 clamps. (Fig 5-1). Discard this hose and clamps

Related Content:

location of draincock on 2007 ford fusion, 05 monte carlo radiator drain, thumb screw missing on 2004 4 3 silverado to drain coolant, procedure for replacing radiator liquid on 2009 Buick Lucerne, picture of 1996 cadillac sedan deville radiatot and hose, is the radiator in 2007 mountaineer one piece, instructions on how to install a radiator in a 2006 Buick LaCrosse, install lowere radiator hose 2007 pontiac g6 3 5, diagram radiator drain plug 3 1 lt jeep, 2007 honda odyssey a/c not working

2002 Toyota Truck 4 Runner Engine, Cooling and Exhaust Cooling System Radiator Removal and Installation Manual

0

Filed Under (Toyota Manuals) by admin on 21-03-2012

download
REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE RADIATOR GRILLE Remove the 7 clips and radiator grille. 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT RADIATOR RESERVOIR HOSE 5. DISCONNECT LOWER RADIATOR HOSE 6. REMOVE RADIATOR NO.2 FAN SHROUD 7. A/T: DISCONNECT OIL COOLER HOSES 8. REMOVE RADIATOR Remove the 4 bolts and the radiator. DISASSEMBLY 1. REMOVE NO.1 FAN SHROUD Remove the 4 bolts and No. 1 fan shroud. 2. REMOVE RADIATOR SUPPORTS 3. REMOVE DRAIN PLUG 4. ASSEMBLE SST SST 09230-01010 a. Install the claw to the overhaul handle, inserting it in the hole in part “A” as shown in the diagram. b. While gripping the handle, adjust the stopper bolt so that dimension “B” shown in the diagram is 0.2 – 0.3 mm (0.008 – 0.012 inch). NOTICE: If this adjustment is not done, the claw may be damaged. 5. UNCAULK LOCK PLATES Using SST to release the caulking, squeeze the handle until stopped by the stopper bolt. SST 09230-01010 6. REMOVE TANKS AND O-RINGS a. Lightly tap the radiator port (inlet or outlet) with a soft faced hammer, and remove the tank. b. Remove the O-ring. REASSEMBLY 1. INSPECT LOCK PLATE Inspect the lock plate for damage. HINT: If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. NOTICE: The radiator can only be recaulked 2 times. After the 2nd time, the radiator core must be replaced. 2. INSTALL NEW O-RINGS AND TANKS a. After checking that there are no foreign objects in the lock plate groove, install the new O-ring without twisting it. HINT: When cleaning the lock plate groove, lightly rub it with sand paper without scratching it. b. Install the tank without damaging the O-ring. c. Tap the lock plate with a soft-faced hammer so that there is no gap between it and the tank. 3. ASSEMBLE SST 09230-01010 a. Install the punch assembly to the overhaul handle, inserting it in the hole in part “A” as shown in the illustration. b. While gripping the handle, adjust the stopper bolt so that dimension “B” shown in the diagram. Dimension “B”: 8.4 mm (0.34 inch) 4. CAULK LOCK PLATE

Related Content:

2001 ford taurus radiator replacement, 2005 kia sorento radiator diagram, 96 taurus radiator diagram, 1999 cadillac seville how to drain radiator, RADIATOR PRESSURE ADAPTER FOR 95 TOYOTA 4-RUNNER, radiator flush on 2002 crown vic, radiator flush 2000 poniac montana you tube, position of fan switches on peugoet 307 1 4 16 valve, pontiac G6 GT radiator schematics, radiator support hole Plugs 67 mustang

1995 Volvo 850 L5-2.3L Turbo Relay Identification and Location

0

Filed Under (Volvo Manuals) by admin on 02-05-2012

download
Relay Identification and Location Relays Inside the Central Electrical Unit 101-102Control module, cruise control (4/3) 103 Fuel pump relay (2/23) 104,108Main headlight relay with bulb malfunction indicator (2/1) 105 Overload relay +X supply (2/30) 106 Overload relay +15 supply (2/31) 107 Overload relay +X supply (2/60) 201 Fog light relay (2/2) 202 Relay, deadlock setting (2/47) 203 Relay, windshield intermittent wiper (2/4) 204 Relay, tailgate intermittent wiper (2/16) 205-206Relay, central lock and delayed inside lighting (2/7) 207 Speed warning (2/51) or exhaust temp. sensor relay (2/15) 208 Relay, heated rear window and door mirrors (2/44) 210-211Relay, anti-theft alarm (2/28) 212 Relay, seat belt reminder/key warning (2/5) 213 Front fog lights, bridge (25/9) 214 Relay, heated rear seat (2/43) If the car is not equipped with a theft alarm, position 210 is bridged and 211 is unconnected. Relays Outside the Central Electrical Unit

Related Content:

diagram gearbox kancil, kancil 850 central lock wiring diagram

2002 Ford F Super Duty 250 550/ Excursion Engine Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 31-05-2012

download
Removal All vehicles 1. Disconnect both battery ground cables. For additional information, refer to Section 414-01 . 2. Loosen the clamps and remove the air cleaner outlet tube. 3. Remove the air intake tube and adapter. 1. Loosen the clamp. 2. Remove the bolts. 3. Lift the tube and adapter, disconnect the wastegate pressure hose, and remove the tube and adapter from the vehicle 4. Remove the degas bottle. For additional information, refer to Section 303-03 . Vehicles equipped with A/C 5. Recover the refrigerant. For additional information, refer to Section 412-00 . All vehicles 6. Remove the radiator grille, and the radiator grille opening panel. For additional information, refer to Section 501-02 . 7. Remove the bolts and position the hood latch aside. 8. Remove the three right side air deflector pushpins. 9. NOTE: Left side shown, right side similar. Remove the air charge cooler retainers. 10. Remove the radiator brackets and position the battery cable aside. 1. Remove the bolts and the brackets. 2. Detach the retainers and position the battery cables aside. 11. NOTE: Right side shown, left side similar. Remove the eight bolts and the radiator upper support. 12. Remove the radiator sight shield. Vehicles equipped with A/C 13. Disconnect the A/C condenser core inlet and outlet tubes. 14. Remove the A/C condenser. All vehicles 15. NOTE: Both the inlet and outlet ducts are removed the same way. Only the outlet duct is shown. Remove the inlet and outlet ducts from the charge air cooler. 1. Loosen the clamp. 2. Detach the ducts from the charge air cooler. 16. Remove the charge air cooler. 17. Disconnect the upper radiator hose from the radiator. 18. Remove the bolts and position the fan shroud on the fan. 19. Raise the vehicle. For additional information, refer to Section 100-02 . 20. Disconnect the degas supply and lower radiator hoses from the radiator. 21. Lower the vehicle. 22. Remove the radiator. 23. Remove the fan shroud. 24. CAUTION: The large clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it. Using the special tools, remove the fan and the fan clutch from the water pump pulley. 25. Rotate the belt tensioner counterclockwise and remove the drive belt. 26. Disconnect the manifold absolute pressure (MAP) sensor hose from the turbocharger compressor manifold.

Related Content:

2007 ford f150 radiater leak, lincoln ls part 303-12/05b 9b659, remove radiator from 2005 chevy malibu, 2002 ford taurus removal radiator, 2005 ford explorer removing radiator, 2007 F150 Radiator replacement procedure, how to remove radiator on 2002 lincoln ls, RADIATOR REMOVAL INSTRUCTIONS 2012 F550, replacing fan clutch kia 2002 sportage manual

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, 86 corvette wiring schematics, location of vent valve solenoid on 2010 ford ranger, damaged fuel pump wiring, proper connection for horn relay 1968 chevelle, fan cable for 1998 dodge caravan, 1998 s10 6 cylindes fuel regulator diagram, pontiac grand am fuel pump wireing harness replacement instructions

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 19-05-2011

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

Related Content:

1981 chevrolet p30 motorhome brake replacement instructions, Honda service manual 1995 accord, 1995 accord repair manual pdf, 2003 buick lesabre lose power for instrument panel and a/c controls, 1989 corvette climate control panel, 2005 honda crv malfunction indicator lamp reset, fuse chart for 2002 chevy silverado 2500 no brake lights, honda accord 61-10 code, fuel circuit outputs on chevy s10, honda accord code 61-1

2005-2009 Toyota Tacoma Electric Fan Kit Installation manual

0

Filed Under (Toyota Manuals) by admin on 16-03-2012

download
INSTALLATION INSTRUCTIONS——— REMOVAL OF EXISTINGF AN AND SHROUD ASSEMBLY: 1. Make sure the engine is cool. 2. Disconnect negative (-) battery cable from battery. 3. Remove plastic protective cover from top of engine/intake manifold. Two acorn nuts located in front are to be removed first. Lift front of cover and notice the cover is hinging at back. Pull to disconnect at pivot point. 4. Remove plastic cover bridging shroud to topcross member. (9 ea) Push-type plastic rivets need to be removed (see Detail 1) . Prying each center post up with a flat-end screwdriver will release fastener. 5. Remove overflow hose from radiator filler neck. 6. Remove top bolts (2ea.) holding fan shroud to radiator side tanks. Save bolts for instal- lationofnew shroud (see Detail 2) . 7. Remove (4ea.) nuts securing fan-clutch assembly (see Detail 3) ; then pull fan-clutch assembly and shroud out simultaneously. 8. Important: Re-secure pulley with new washers of kit bag#13615 and original pulley nuts. Detail1 Plastic Cover Plastic Rivets Detail2 Save bolts for new installation rev. 04-20-09 part no. 99678 Detail3 INSTALLATION OF NEW ELECTRIC FAN SHROUD: 1. Mount bracket#67802 to driver’ssideofshroud. Use the hex bolts and washers provided. Note: Leave the bracket loosely mounted for now; you will adjust and tighten them later (see Detail 4& 4a) . 2. Lower shroud, with one bracket only, into position inserting bottom of bracket into slot at bottom of side tank (driver’sside). Loosely secure top of bracket using factory bolt, saved from step#6 of page 1 3. Attach overflow tank to bracket#67801 using supplied hardware included with overflow tank (see Detail4&4b) . 4. Attach bracket#67801 to passenger’ssideradiator tank and fan shroud; a. Insert bottom of bracket into slot at bottom of side tank. b. Loosely secure top of bracket using factory bolt, saved from step#6. c. Mount bracket loosely to shroud using the hex bolts and washers provided (see Detail 4 &4b) . 5. After both brackets and shroud are attached; make final adjustments utilizing slots provided. When tightening the brackets, adjust the fan so that the rubber seal is contacting the radiator core and compress the seal about~50%. Note: It may help to have a friend hold the fan against the core while tightening brackets. 6. Mount rubber hose supplied to radiator filler neck and to the shorter of the two tubes protruding from bottom of overflow tank (see Detail 4) . 7. If you disconnected any hoses or drained coolant to install the fan, reconnect the hoses and refill the radiator. At this time fill overflow tank~25%of capacity

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

wiring diagram for the drivers side front electric window switch on a 1998 ford contour, 02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

Related Content:

ford focus 2001 wiring harness replacement, replace 2006 ford escape radiator, 1998 pontiac montana block drains, cooling fan wiring diagram for 2004 impala with police package, dodge caravan cooling fan connector removal, how to replace 2008 escape radiator fans