Skip to content

2001 dodge ram heater diagram

You search PDF repair manual about 2001 dodge ram heater diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

TOYOTA BLOCK HEATER APPLICATION INSTALLATION INSTRUCTIONS

download
Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level. 3 AVALON 2005- 2010 2GR-FE PU140-00900 PU140- 03571 Rear, L.H.S. (hole direction pointing to front) Route cord up. Tie the cord to the lower heater hose outlet. Route the cord to left side of engine. Tie the cord to the main harness besides the fuse box. Remove front radiator plastic cover. Route the cord down on left side of battery and tie the cord to the left side of radiator coolant fan harness at the front bottom of the battery. Route the cord to the front and tie to the front grille. 11 1983- 86 2SE C0140-00123* C0140- 00069 Front L.H.S. 2nd from transmission 6 1987- 91 3S-FE C0140-00134* C0140- 00070 Rear 2nd from right 12 1988- 91 2V-ZFE C0140-00110* C0140- 00767 Front centre. Loosen union bolt of water outlet five revolutions before refilling coolant. Tighten after coolant fill. 12 1992- 93 3VZ-FE C0140-01141* C0140- 00903 Front 1st from left. Remove exhaust manifold; remove exhaust pipe if necessary. Route cordset towards the left side of engine compartment. 6 1992- 2001 5S-FE C0140-01123* C0140- 02899 Front, 2nd from left. Remove exhaust manifold. For models prior to 1994 model year, remove upper exhaust manifold heat shield only. Route cordset towards left side of engine compartment. 12 CAMRY 1994- 2006 IMZ-FE C0140-00644* C0140- 02897 Front, R.H.S. Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level

2001 Dodge Dakota CENTRAL TIMER MODULE REMOVAL AND INSTALLATION MANUAL

download
1. Connect scan tool to Data Link Connector (DLC), under lower left side of instrument panel. Turn ignition on. Using scan tool, attempt to communicate with Air Bag Control Module (ACM) and Controller Antilock Brake (CAB) module. If scan tool is able to identify or communicate with ACM and CAB, go to next step. If scan tool is not able to identify or communicate with ACM and/or CAB, perform appropriate DTC or symptom test. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION and SYMPTOM IDENTIFICATION tables under SELF-DIAGNOSTIC SYSTEM. 2. Turn ignition off. Disconnect Gray 26-pin Central Timer Module (CTM) connector C1. CTM is located behind left side kick panel. Ensure interior lights are off. Using DVOM, measure resistance between ground and Gray 26-pin CTM connector C1 terminals No. 1 and 16 (Black/Light Green wires) and No. 2 (Black wire). See Fig. 5 . If resistance is 10 ohms or less on each ground circuit, go to next step. If resistance is more than 10 ohms on any ground circuit, check for an open between appropriate CTM connector terminal and ground. See GROUND DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 3. Disconnect Gray 12-pin CTM connector C3. Using test light connected to ground, probe Gray 12-pin CTM connector C3 terminals No. 1 (Red/Tan wire) and No. 6 (Red/Light Green wire). See Fig. 8 . If test light illuminates on both circuits, go to next step. If test light does not illuminate on both circuits, check for open in appropriate circuit between power distribution center and CTM. See POWER DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 4. Turn ignition on. Using scan tool, ensure there is PCI BUS communication with other modules (besides the ACM and CAB). If scan tool is able to identify or communicate with all modules, go to next step. If scan tool is not able to identify or communicate with all modules, refer to appropriate communications symptom for diagnosis. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION table under SELF-DIAGNOSTIC SYSTEM. 5. Connect Scope Input Cable (CH7058) to channel one connector on scan tool. Connect Cable-To-Probe Adapter (CH7062) and Black and Red test probes to scope input cable. Connect Black test probe to ground. Connect Red test probe to PCI BUS circuit at Gray 26-pin CTM connector C1 terminal No. 10 (Violet/Yellow wire). 6. Using scan tool, select PEP MODULE TOOLS, LAB SCOPE, LIVE DATA. Select 12 VOLT SQUARE WAVE. Press F2 for SCOPE. Press F2 and use DOWN arrow to set voltage scale to 20 volts. Press F2 again when complete. Turn ignition on. If reading on lab scope toggles between zero and 7.5 volts, go to next step. If reading on lab scope does not toggle between zero and 7.5 volts, repair open in PCI BUS circuit (Violet/Yellow wire). 7. Replace CTM. See CENTRAL TIMER MODULE under REMOVAL & INSTALLATION

1993 BMW 325i (E36) Removing and Installing/ Replacing Heater and Air Conditioning Fan (M50, S50, M52)

download
With Air Conditioning Notes Removing and Installing/Replacing Heater and Air Conditioning Fan (M50, S50, M52) * Additional work on 2-door model: Remove console for the windshield wiper system. * Position windscreen wiper, left, vertically. * Pull off rubber part and pry out grill. Zoom Sized for Print Zoom Sized for Print * Remove screws from cable channel. * Remove screws on right-hand side and take off holder. * Unscrew left-hand screw. * Pull out air collector in upwards direction. Note: Air collector will be difficult to pull out. M50, M52 Unclip covers. Unscrew bolts. Remove cover of injection-valve plate. * Unclip covers and remove screws. * Remove cover * Unfasten clips and remove blower cover. * Disconnect connector. * Unfasten clips and lift out left upper section of blower. Note: The air conditioning system remains installed. Illustration shows air conditioning unit removed.

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE