2001 ford focus radiator hose diagram

You search PDF repair manual about 2001 ford focus radiator hose diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2001 ford focus radiator hose diagram Direct Download speed 5432 Kb/s

  2001 ford focus radiator hose diagram Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, how to change power steering pump 2009 acada, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, how to replace 2003 impala power steering pump

2002 Toyota Truck 4 Runner Engine, Cooling and Exhaust Cooling System Radiator Removal and Installation Manual

0

Filed Under (Toyota Manuals) by admin on 21-03-2012

download
REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE RADIATOR GRILLE Remove the 7 clips and radiator grille. 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT RADIATOR RESERVOIR HOSE 5. DISCONNECT LOWER RADIATOR HOSE 6. REMOVE RADIATOR NO.2 FAN SHROUD 7. A/T: DISCONNECT OIL COOLER HOSES 8. REMOVE RADIATOR Remove the 4 bolts and the radiator. DISASSEMBLY 1. REMOVE NO.1 FAN SHROUD Remove the 4 bolts and No. 1 fan shroud. 2. REMOVE RADIATOR SUPPORTS 3. REMOVE DRAIN PLUG 4. ASSEMBLE SST SST 09230-01010 a. Install the claw to the overhaul handle, inserting it in the hole in part “A” as shown in the diagram. b. While gripping the handle, adjust the stopper bolt so that dimension “B” shown in the diagram is 0.2 – 0.3 mm (0.008 – 0.012 inch). NOTICE: If this adjustment is not done, the claw may be damaged. 5. UNCAULK LOCK PLATES Using SST to release the caulking, squeeze the handle until stopped by the stopper bolt. SST 09230-01010 6. REMOVE TANKS AND O-RINGS a. Lightly tap the radiator port (inlet or outlet) with a soft faced hammer, and remove the tank. b. Remove the O-ring. REASSEMBLY 1. INSPECT LOCK PLATE Inspect the lock plate for damage. HINT: If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. NOTICE: The radiator can only be recaulked 2 times. After the 2nd time, the radiator core must be replaced. 2. INSTALL NEW O-RINGS AND TANKS a. After checking that there are no foreign objects in the lock plate groove, install the new O-ring without twisting it. HINT: When cleaning the lock plate groove, lightly rub it with sand paper without scratching it. b. Install the tank without damaging the O-ring. c. Tap the lock plate with a soft-faced hammer so that there is no gap between it and the tank. 3. ASSEMBLE SST 09230-01010 a. Install the punch assembly to the overhaul handle, inserting it in the hole in part “A” as shown in the illustration. b. While gripping the handle, adjust the stopper bolt so that dimension “B” shown in the diagram. Dimension “B”: 8.4 mm (0.34 inch) 4. CAULK LOCK PLATE

Related Content:

2001 ford taurus radiator replacement, 2005 kia sorento radiator diagram, 96 taurus radiator diagram, 1999 cadillac seville how to drain radiator, radiator flush on 2002 crown vic, radiator flush 2000 poniac montana you tube, position of fan switches on peugoet 307 1 4 16 valve, pontiac G6 GT radiator schematics, losing coolant in 2004 pontiac grand prix radiator drain plug, RADIATOR PRESSURE ADAPTER FOR 95 TOYOTA 4-RUNNER

2007 TOYOTA TUNDRA SUPERCHARGER FIT KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 20-03-2012

download
1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 3, save this coolant as it will be reused. CAUTION: To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause the hot engine coolant and steam to blow out from the radiator. (h) All parts that are removed and not reused should be saved for the customer, i.e., “discard” means to save for the customer 2. Cover Removal. (a) Remove the engine V-bank cover by Lifting the front of the cover and pulling away from the firewall (Fig 2-1). Discard these parts. (b) If installed, remove the No. 1 engine under cover (Fig 2-2) by removing the 3 screws and 5 bolts. Save these parts for reuse. 3. Drain Engine Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns. (a) Loosen the radiator drain cock plug (Fig. 3-1). (b) Remove the radiator cap. Then drain the coolant from the radiator into a clean container so it can be reused (Fig. 3-1). (c) Loosen the 2 cylinder block drain cock plugs (Fig.3-1). Then drain the coolant from the engine and save for reuse. (d) Tighten the 2 cylinder block drain cock plugs. Torque: 13 Nm (10 ft lbf) 4. Fan and Shroud Removal. (a) Remove the upper radiator hose. Mark the radiator end of this hose with a marker or tape. This hose will be re-installed inverted and the mark will help identify the ends. (b) Loosen the 4 nuts holding the fluid coupling fan (Figs. 4-1). (c) Remove the fan/generator V-rib belt. Discard this belt as it will be replaced by a new belt. (d) Disconnect the reservoir hose from the upper radiator tank. (e) For vehicles with Trailer Towing System: Detach the claw to open the No. 1 hose clamp on the side of the fan shroud (Fig 4-2). (f) Remove the 2 bolts holding the fan shroud (Figs 4-3). Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan. Retain these parts for reuse. Temporarily re-install the 4 nuts to keep the pulley in place (reference Fig 4-1). Do not tighten. CAUTION: Be careful not to damage the radiator core. It is helpful to protect the radiator core with a piece of cardboard to prevent damage during subsequent steps. 5. Air Cleaner Lower Box Replacement. (a) Remove the air cleaner hose by disconnecting the vacuum and ventilation hoses and loosening the 2 clamps. (Fig 5-1). Discard this hose and clamps

Related Content:

location of draincock on 2007 ford fusion, 05 monte carlo radiator drain, thumb screw missing on 2004 4 3 silverado to drain coolant, procedure for replacing radiator liquid on 2009 Buick Lucerne, picture of 1996 cadillac sedan deville radiatot and hose, is the radiator in 2007 mountaineer one piece, instructions on how to install a radiator in a 2006 Buick LaCrosse, install lowere radiator hose 2007 pontiac g6 3 5, diagram radiator drain plug 3 1 lt jeep, 2007 honda odyssey a/c not working

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

555 ford backhoe repair manual, How to Fix Po446 Code ford escape xls, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, Ford E 450 Cutaway Manual, where is the vct solenoid located on a 2009 ford escape, 1988 ford f150 302 where is Diagostic Link Connector located, ford 9 inch repair manual, ford edge sunroof repair pdf, how many quarts of transmission fluid does 2012 ford e450 take?

2002 Ford F Super Duty 250 550/ Excursion Engine Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 31-05-2012

download
Removal All vehicles 1. Disconnect both battery ground cables. For additional information, refer to Section 414-01 . 2. Loosen the clamps and remove the air cleaner outlet tube. 3. Remove the air intake tube and adapter. 1. Loosen the clamp. 2. Remove the bolts. 3. Lift the tube and adapter, disconnect the wastegate pressure hose, and remove the tube and adapter from the vehicle 4. Remove the degas bottle. For additional information, refer to Section 303-03 . Vehicles equipped with A/C 5. Recover the refrigerant. For additional information, refer to Section 412-00 . All vehicles 6. Remove the radiator grille, and the radiator grille opening panel. For additional information, refer to Section 501-02 . 7. Remove the bolts and position the hood latch aside. 8. Remove the three right side air deflector pushpins. 9. NOTE: Left side shown, right side similar. Remove the air charge cooler retainers. 10. Remove the radiator brackets and position the battery cable aside. 1. Remove the bolts and the brackets. 2. Detach the retainers and position the battery cables aside. 11. NOTE: Right side shown, left side similar. Remove the eight bolts and the radiator upper support. 12. Remove the radiator sight shield. Vehicles equipped with A/C 13. Disconnect the A/C condenser core inlet and outlet tubes. 14. Remove the A/C condenser. All vehicles 15. NOTE: Both the inlet and outlet ducts are removed the same way. Only the outlet duct is shown. Remove the inlet and outlet ducts from the charge air cooler. 1. Loosen the clamp. 2. Detach the ducts from the charge air cooler. 16. Remove the charge air cooler. 17. Disconnect the upper radiator hose from the radiator. 18. Remove the bolts and position the fan shroud on the fan. 19. Raise the vehicle. For additional information, refer to Section 100-02 . 20. Disconnect the degas supply and lower radiator hoses from the radiator. 21. Lower the vehicle. 22. Remove the radiator. 23. Remove the fan shroud. 24. CAUTION: The large clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it. Using the special tools, remove the fan and the fan clutch from the water pump pulley. 25. Rotate the belt tensioner counterclockwise and remove the drive belt. 26. Disconnect the manifold absolute pressure (MAP) sensor hose from the turbocharger compressor manifold.

Related Content:

2007 ford f150 radiater leak, lincoln ls part 303-12/05b 9b659, remove radiator from 2005 chevy malibu, 2002 ford taurus removal radiator, 2005 ford explorer removing radiator, 2007 F150 Radiator replacement procedure, how to remove radiator on 2002 lincoln ls, RADIATOR REMOVAL INSTRUCTIONS 2012 F550, replacing fan clutch kia 2002 sportage manual

2008-2010 FORD F-Super Duty DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 17-01-2012

download
DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE ISSUE ECT temp. Some 2008-2010 F-Super Duty vehicles built on or b. Test results/next steps: before 9/14/2009 and equipped with a 6.4L diesel engine may exhibit repeat radiator leaks due to (1) If EOT is less than 8 °F (4.4 °C) malfunctioning (hyper-extended) high temperature higher than ECT, and the coolant temp thermostats. fluctuates roughly 5 °F (2.7 °C) – the thermostats are okay and do not need ACTION to be replaced. Replace just the Follow the Service Procedure steps to correct the radiator. Refer to WSM, Section 303-03 condition. (Engine Cooling). SERVICE PROCEDURE (2) If EOT exceeds ECT by greater than 8 °F (4.4 °C) or if the ECT readings 1. Verify the coolant leak is from the radiator, refer fluctuate 10 to 12 °F (5.55-6.66 °C) to pinpoint test (PPT) A found in the Workshop roughly every 30 seconds – replace Manual (WSM), Section 303-03. both thermostats and radiator. Refer to 2. Verify the venturi tee is installed. WSM, Section 303-03 (Engine Cooling). a. If installed, confirm it is installed correctly (note – orientation direction on part). 5. If vehicle is not drivable and the coolant leak is found to be from the radiator, remove and b. If not installed, install Venturi Tee Kit on replace both thermostats and radiator. Refer to vehicles built on or before 5/15/2008. WSM, Section 303-03 for both radiator and thermostat removal procedure and approved 3. Prepare the vehicle for a test drive. cooling system draining, filling and bleeding a. If the coolant leak at the radiator is large procedures. enough to cause an unsafe test drive or potential for engine/vehicle damage, proceed PART NUMBER PART NAME to Step 5. 8C3Z-8575-D Thermostat Assembly 8C3Z-8009-B Radiator Assembly b. Before driving the vehicle confirm the 8C3Z-8B379-B Venturi Tee coolant level is at minimum level or above in the degas bottle. If required, add 50/50 WARRANTY STATUS: Eligible Under Provisions Of mix to coolant bottle. New Vehicle Limited Warranty Coverage 4. Test Drive – use an Integrated Diagnostic IMPORTANT: Warranty System (IDS) or equivalent and monitor engine coverage limits/policies are oil temperature (EOT) and engine coolant not altered by a TSB. temperature (ECT) parameter identifiers (PIDS). Warranty coverage limits are determined by the identified causal par

Related Content:

08 f350 radiator replacemnt, how to change thermostat in a 2011 chevy cruze, 2010 F150 Thermostat, f150 ceiling leak, ford focus thermostat does both ends move when hot, replacing saturn aura xe 2008 cooling fan, thermostat housing bolts 2009 focus torkspec

2002 Ford Explorer Sport/ Sport Trac Cylinder Head Removal and installation manual

0

Filed Under (Ford Manuals) by admin on 02-06-2012

download
Removal Both cylinder heads 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information , refer to Section 100-02 . 2. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Drain the cooling system. For additional information, refer to Section 303-03 . 4. Remove the intake manifold. For additional information, refer to Intake Manifold in this section. 5. Remove the cooling fan shroud. For additional information, refer to Section 303-03 . 6. Remove the accessory drive belt. For additional information, refer to Section 303-05 7. Remove the LH valve cover. For additional information, refer to Valve Cover — LH in this section. 8. Remove the RH valve cover. For additional information, refer to Valve Cover — RH in this section. 9. Disconnect the generator electrical connections. 10. Remove the accessory drive belt tensioner. 11. Remove the bolts and the generator and generator mounting bracket as an assembly. 12. Disconnect the crankshaft position (CKP) sensor electrical connector. 13. Disconnect the wiring harness retainers. 14. Disconnect the water temperature indicator sender unit and the engine coolant temperature (ECT) sensor electrical connectors. 15. Disconnect the exhaust gas recirculation (EGR) tube fitting. 16. Remove the upper heater coolant hose. 1. Squeeze the heater hose clamp. 2. Remove the heater coolant hose. 17. Remove the lower heater coolant hose and position aside. 1. Remove the bolt. 2. Squeeze the hose clamp. 3. Remove the heater coolant hose and position aside. 18. NOTE: The coolant hose will be removed with the thermostat housing. Move the coolant bypass hose clamp off the water pump outlet. 19. Remove the bolts, the thermostat housing and the bypass hose. 20. Remove the bolt and detach the wiring harness retainer. 21. Remove the bolts and position the accessory drive bracket aside.22. Detach the wiring harness retainer. 23. Remove the bolt and the oil level indicator tube. 24. Using the special tool, disconnect the LH spark plug wires from the spark plugs. 25. Disconnect the fuel pulse damper vacuum connector. 26. Remove the four bolts and position the fuel supply tube aside. 27. Remove the bolts and the fuel rail and injectors as an assembly.28. NOTE: Mark each of the roller followers to make sure it is installed in its original position during reassembly. Use the special tool to remove the roller followers. 29. Remove the lower radiator hose. 30. Remove the nut and position the A/C tube bracket aside. 31. Using the special tool, set the No. 1 piston at top dead center (TDC). RH cylinder head 32. Remove the RH fenderwell splash shield. 33. Remove the RH camshaft chain tensioner.

Related Content:

removal of 2000 expedition heater houses, 2001 ford sport trac lower intake gastket diagram, Ford Expedition Heater Hose Removal, ford explorer sport trac thermostat gasket installation, ford explorer valve cover removal, how to Repair 2007 ford expedition rear heater hose, low oil sensor bypass, remove bottom radiator hose on pt cruiser to drain engine block, shop manual 2002 ford sort trac

2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

Related Content:

4D35 engine repair manual, 6m70 wiring diagram, 2000 Nissan sentra 1 8 engine bolt torque diagram, so5d engine repair manual, so5d engine, TOYOTA SO5D SERVICE MUNAL, what causes damage to a flywheel on a 2004 yukon, SO5D OBD ll Code, 2005 chevy impala motor diagram, Position of sensors in mitsubishi 4m 51 engine

1998 Dodge Truck Caravan Replace Radiator Fan Relay

0

Filed Under (Dodge Manuals) by admin on 16-06-2011

download
1. With the ignition key in the OFF position, disconnect the battery. 2. Remove the two (2) screws that attach the air inlet resonator to the upper radiator support. 3. Disconnect the upper and lower air inlet hoses from the resonator and remove the resonator. 4. Remove the air cleaner housing. 5. Locate the radiator cooling fan relay on the left front inner frame rail just behind the radiator (Figure 1). 6. Disconnect the radiator fan relay wiring connector. 7. Remove the radiator fan relay. Discard the relay and the attaching screws. 8. Install the new radiator fan relay using the supplied screws. Tighten the screws to 35 in-lbs (4 N.m). CAUTION: Do not over torque screws. To ensure heat transfer and proper operation, the new radiator fan relay must be installed using both of the provided screws. 9. Connect the radiator fan relay electrical connector. Slide the red latch to the locked position. 10. Install the air cleaner housing. 11. Install the resonator assembly and connect the upper and lower air inlet hoses. 12. Install the resonator to upper radiator support screws. Tighten the screws securely. 13. Connect the negative battery cable.

Related Content:

ford focus 2001 wiring harness replacement, replace 2006 ford escape radiator, 1998 pontiac montana block drains, cooling fan wiring diagram for 2004 impala with police package, dodge caravan cooling fan connector removal, how to replace 2008 escape radiator fans

2003-2005 Toyota Corolla HEATER PERFORMANCE IMPROVEMENT Repair Manual

0

Filed Under (Toyota Manuals) by admin on 23-01-2012

download
HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 3 of 15 Install Air Conditioner Unit Assembly. Air Conditioner Unit Assembly 1. Evacuate Refrigerant HFC-134a (R-134a). Equipment: Robinair R-134a Refrigerant Recovery/Recycling Machine (Robinair P/N: 342000) 2. Disconnect Negative Terminal of Battery. 3. Drain Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot, as coolant and steam can be blown out under pressure. A. Remove the radiator cap. B. Loosen the radiator and engine drain plugs and drain the coolant. C. Close the drain plugs. Engine Drain Torque: 13 Nm (130 kgfcm, 9 ftlbf) HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 4 of 15 4. Disconnect Cooler Refrigerant Suction Hose No. 1. A. Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system. Disconnect the same way as cooler refrigerant suction hose No. 1. 6. Disconnect Heater Inlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater inlet water hose. 7. Disconnect Heater Outlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater outlet water hose. 8. Place Front Wheels Facing Straight Ahead. 9. Remove Horn Button Assembly. NOTE: If the airbag connector is disconnected with the ignition switch ON, DTCs will be recorded. Before working on SRS, please refer to the Technical Information System (TIS), 2005 model year Corolla Repair Manual: Supplemental Restraint System: Supplemental Restraint System: Precaution. A. Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case.

Related Content:

freon capacities for scion, 07 chevy malibu parasitic load, 134a evaporator for ae2 corolla xl, 2005 tahoe sunroof drain lines, How to disengage clutch on SST 16, scion xb 2005 proper a/c refrigerant pressure, sst 16 parts manual

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, how to change power steering pump 2009 acada, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, how to replace 2003 impala power steering pump