2001 lanos daewoo cooling system diagram

You search PDF repair manual about 2001 lanos daewoo cooling system diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2001 lanos daewoo cooling system diagram Direct Download speed 5432 Kb/s

  2001 lanos daewoo cooling system diagram Full Version speed 8172 Kb/s



2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

Related Content:

2000 Nissan sentra 1 8 engine bolt torque diagram, SO5D OBD ll Code, TOYOTA SO5D SERVICE MUNAL, so5d engine repair manual, what causes damage to a flywheel on a 2004 yukon, 2005 chevy impala motor diagram, perodua engine overhall pdf, 4EFE engine manual, Position of sensors in mitsubishi 4m 51 engine, TOYOTA SO5D SERVICE MANUAL

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 2007 kia rio service manual, 200lolds aleroraditor system, schematic for front brakes on 2005 Buick Rendezvous, 4t65e service manual online, w584a lincoln, 2007 Chevy Colorado Gas Tank Seal replace, pontiac 2007 g6 remove radiator cover

1996-2001 Honda Civic – ALL Civic Rear Main Oil Seal Leaks Repair manual

0

Filed Under (Honda Manuals) by admin on 14-04-2012

download
REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine warm up to its normal operating temperature (the cooling fan cycles twice). Let the engine idle (throttle fully closed with all electrical items turned off) for 10 minutes. 8. 2001 2-door EX and LX models only. Drive the vehicle above 40 mph for 5 to 10 minutes with the cruise control on. (This lets the cruise control actuator learn how much slack there is in the throttle cable.)

Related Content:

96 honda crv engineb20b repair manual free

2001 HONDA Civic EX Replace the cylinder head assembly REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 06-06-2011

download
1. Remove the cylinder head (see page 6-30 of the 2001-02 Civic Service Manual), and discard it. 2. Inspect the TDC sensor and the timing belt covers for damage (see page 6-57 of the service manual). Replace any damaged parts. 3. Install the new cylinder head (see page 6-50 of the service manual). 4. Check the engine oil level; add oil if necessary.
2 of 2 01-083 5. Do the Idle Learn Procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine reach its normal operating temperature (the cooling fan cycle twice). Let the engine idle (throttle fully closed and with all electrical items off) for 10 minutes. 6. If you are working on a 2001 Civic 2-door EX, do the Cruise Control Learn Procedure. Drive the vehicle, and set the cruise control above 40 miles per hour. Continue driving the vehicle for 5 to 10 minutes. NOTE: You can use a smog/chassis dynamometer to do this step instead of driving the vehicle. Do not do this step with the vehicle on a lift.

Related Content:

hond civic 2001 ex underhood diagram, 2001 honda civic a/c diagram, torque converter 01 civic repair

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, 99 buick park ave radiator installation, Rav 4 steering rack dismantle and refit procedure, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle

2003 GMC Truck C 1500 P/U 2WD Engine Knocking or Lifter Noise

0

Filed Under (GMC Manuals) by admin on 30-06-2012

download
Engine Lubrication: All Technical Service Bulletins Engine – Knocking or Lifter Noise File In Section: 06 – Engine/Propulsion System Bulletin No.: 02-06-01-038 Date: December, 2002 TECHNICAL Subject: Engine Knock or Lifter Noise (Replace 0-Ring) Models: 2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT 2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4) Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter . Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi). Cause The 0-ring seal between the oil pump screen and the oil pump may be cut, causing aeration of the oil. Correction

Related Content:

2003 mitsubishi lancer es repair manual, 2003 chevrolet suburban ac evaporator, 2003 ford motorhome chassis repair manual, 2003 pontiac vibe repair manual, engine replacement procedure 2003 honda odyssey, evap in 2003 chevy s10 pickup, front end diagram for a gmc 03 envoy, fuse diagram for 2003 impalaq, GMC Sierra 2003 Manual, replace tccm in a 2003 tahoe

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, how to check radiator fluid level pontiac grand prix, Low coolant light olds intrigue, evap sensor on 2002 suburban, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 2002 mercury sable cooling system, 2006 Envoy low idle

2001-2008 GM 1500/2500 Series Pick-Up Edelbrock Header Installation Manual

0

Filed Under (GMC Manuals) by admin on 25-02-2012

download
INSTALLATION INSTRUCTIONS DISASSEMBLY 1. Disconnect negative battery cable. 2. Unbolt exhaust pipes from manifolds. RIGHT SIDE 1. Disconnect and remove spark plug wires. 2. Unbolt and remove dipstick tube. 3. Unbolt and remove manifold from top. 4. Install flange gasket and header from top. Install header bolts, lock washers, and thick flat washers supplied. Note: Ensure proper alignment on slotted holes of port flange and only snug bolts at this time. 5. Re-install spark plug wires. 6. Re-install dipstick tube. 7. Some models may require the aluminum heat shield under the A/C receiver dryer to be re-positioned, adjusted or bent to gain some clearance between header and heat shield. LEFT SIDE 1. Disconnect and remove spark plug wires. 2. Unbolt and remove manifold. 3. Install flange gasket and header from top. Install header bolts, lock washers, and thick flat washers supplied, ensure proper alignment and only snug bolts at this time. IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in poor performance and engine or vehicle damage.
©2007 Edelbrock Corporation Catalog #65022 & 65023 Page 2of 2 Brochure #63-0364 Rev. 8/07 – DA/mc Edelbrock Corporation, 2700 California St., Torrance, CA 90503 Tech Line: 1-800-416-8628 Office: 310-781-2222 Tech Fax: 310-972-2730 E-Mail: Edelbrock@Edelbrock.com 2. Using supplied hardware, re-attach the factory exhaust pipes to the headers and tighten bolts evenly to ensure a tight seal. ( Note: The 7/16 x 2 bolts are to be used on 4.8L, 5.3L, & some 6.0L V8s. The 7/16 x 1 ¾ are for the left side of 4.8L & 5.3L V8s, and on the 6.0L V8 that do not have OEdonut gaskets. 3. After the factory exhaust pipes have been tightened to the collector flange of the header, tighten the port flange bolts to recommended factoryspecifications. FINAL INSPECTION 1. Check all lines (hydraulic, vacuum, air conditioning and fuel) to ensure there is adequate clearance to headers. 2. Re-connect battery. 3. At this point, it is a good idea to look everything over and make sure that nothing was missed in assembly. 4. Start vehicle and bring up to normal operating temperature. Check for possible leaks. 5. Turn engine off and let cool. Tighten all bolts again. Note: Thick washers are to be used on slotted holes of port flange. 4. Re-install spark plug wires. Note: Due to production tolerance, it may be necessary to bend the motor mount heat shield for better clearance. ASSEMBLY OF EXHAUST PIPE Note: Some 2007 model year vehicles will have a donut gasket on the right side OE exhaust manifold. If your vehicle has that donut gasket, it will be re-used with your shorty headers (see below). This system comes with 2 exhaust crush rings. On 2001- 2006 4.8L & 5.3L V8s, one will be used on the left side collector. On 2001-2006 6.0L vehicles will use one on the left side and one on the right side to replace factory-installed crush rings. 1. On 4.8L, 5.3L, &6.0L V8s with donut gasket – Remove the donut gasket from right side exhaust manifold. Using a pair of pliers, remove the retaining ring from the donut gasket and place the donut gasket in flare of factory exhaust pipe.

Related Content:

schematics on bleeding the air from cooling system on 02 aurora, snug top wiring, 2001 chevy hd 2500 code p1626, bumper sealer used on a muffler, how to repair exhaust flange leaks on chevy tahoe, what is the diameter of the exhaust pipe for 2001 malibu

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

0

Filed Under (Honda Manuals) by admin on 27-06-2012

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

Related Content:

1999 honda civic ex manual, ashley recliner model 7528 parts, 2001 civic fuel canister pdf, ashley recliner model 7528 replacement parts, Honda Odyssey 2001 Parts Diagram, honda odyssey 2002 repair manual pdf, honda odyssey canister purge valve location, Savage Model 99 Manual, viper 4115v1remote start

2000 Ford Ranger Cooling System Draining Filling and Bleeding Repair Manual

0

Filed Under (Ford Manuals) by admin on 10-07-2012

download
NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle, For additional information, refer to Section 100-02 . 3. Remove the lower radiator cover. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant such as VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants can degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, or brine, or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolants unless they meet the requirements of Ford specification ESE-M97B44-A or WSS-M97B51-A1. Not all coolant recycling processes meet these Ford specifications. Use of such coolants can harm the engine and cooling system components. All engines 1. Install the lower radiator cover.

Related Content:

2002 ford ranger cooling system diagram, WSS-M97B44-D and d2 different, m440 cooling system pdf, cooling system diagram for a 1999 ford expedition, cooling system in 2012 mazda 6, diagram of coolant system of a Ford 2008 Expedition, diagram of cooling system for a 2005 ford explorer, radkitplus1, FREE 2002 LINCOLN LS COOLING SYSTEM DIAGRAM, isuzu 3 2l cooling system diagram

Related Content:

2000 Nissan sentra 1 8 engine bolt torque diagram, SO5D OBD ll Code, TOYOTA SO5D SERVICE MUNAL, so5d engine repair manual, what causes damage to a flywheel on a 2004 yukon, 2005 chevy impala motor diagram, perodua engine overhall pdf, 4EFE engine manual, Position of sensors in mitsubishi 4m 51 engine, TOYOTA SO5D SERVICE MANUAL