2001 mitsubishi montero 3 5l timing mark

You search PDF repair manual about 2001 mitsubishi montero 3 5l timing mark, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2001 mitsubishi montero 3 5l timing mark Direct Download speed 5432 Kb/s

  2001 mitsubishi montero 3 5l timing mark Full Version speed 8172 Kb/s



2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

0

Filed Under (Daewoo Manuals) by admin on 13-05-2011

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, 2002 jetta crank mark, 2003 eclipsed2 4 litre cranckshaft position sensor location, 3126 timing pin hole, 91 honda accord timing belt marks diagram, 98 eclipse rs service manual, changing timing belt 2004 kia optima EX 2 7 6 cylinder ?, how to adjust belt on 2001 kia optima, kia rio 5 2007 timming belt

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

0

Filed Under (Mitsubishi Manuals) by admin on 14-01-2012

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, montero crank shaft pully removal, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero, engine torque specs 2000 mitsubishi montero 3 5 sohc

1996 Mitsubishi Eclipse GS-T TIMING BELT And BALANCE SHAFT BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 29-04-2012

download
Removal 1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B Inspection 1. Inspect timing belts for damaged teeth and cracking. Ensure belts are not contaminated with oil. Check tensioners for free rotation and grease leakage. Replace components if damaged or if grease leakage exists. 2. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 6 . Length should be .47″ (12 mm). Apply 22-44 lbs. (10-20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39″ (1 mm), replace the auto tensioner.

Related Content:

1996 nissan pathfinder timing set-up, 1996 toyota rav 4 timing belt replacement, belt diagram for 1996 toyota corola, check timing eclipse gst, timing spec diagram 1996 mitsubishi montero

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

2003 Kia Rio L4-1.6L DOHC TIMING BELT Service and Repair Manual

0

Filed Under (Kia Motors Manuals) by admin on 28-06-2012

download
REMOVAL 1. Disconnect negative battery cable. 2. Loosen power steering lock bolts and nuts accordingly and remove tension from Power Steering (P/S) and/or Air Conditioning (A/C) compressor drive belt . 3. Remove P/S and/or A/C drive belt . 4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts. 6. Remove water pump pulley. 7. Remove crankshaft pulley and timing belt guide plate. 8. Remove upper and lower timing belt covers. 9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine. 10. Check that “I” mark on intake camshaft pulley is aligned with mark on cylinder head cover and “E” mark on exhaust camshaft pulley is aligned with mark on cylinder head cover. NOTE: Do not move camshaft or crankshaft once timing marks have been correctly positioned. 11. Loosen tensioner pulley lock bolt. 12. Protect timing belt with a rag. 13. Remove tensioner pulley. 14. Remove timing belt. NOTE: Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation. INSPECTION NOTE: Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt. 1. Replace timing belt if it is contaminated with oil or grease

Related Content:

o2 Chevy Blazer check engine light code po763, crankshaft timming mark isuzu kb300, How to change kia picanto oil seals, kia picanto radiator how to remove, kia sephia crank sensor p, kia sephia crankshaft angle pin out, p0748 kia, picanto crank seal replacement, sensor efi system kia carens

1994 Mitsubishi Expo LRV TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 30-04-2012

download
Removal 1. Remove radiator shroud, cooling fan and pulley. Remove all drive belts and crankshaft pulleys. Remove upper timing belt covers and gaskets. Note bolt length and location. 2. Remove crankshaft sprocket bolt and washer. Rotate crankshaft clockwise (as viewed from timing belt end of engine) until cylinder No. 1 is at TDC of compression stroke. Align timing mark on camshaft sprocket with mark on cylinder head. See Fig. 5 . 3. Loosen timing belt tensioner adjustment bolt, and move tensioner toward water pump. Tighten bolt to secure tensioner. Remove front timing belt and tensioner. DO NOT rotate crankshaft after timing belt has been removed. 4. Remove camshaft sprocket (if necessary). Remove oil pump sprocket access plug from cylinder block. See Fig. 4 . Insert a .31″ (8.0 mm) diameter Phillips screwdriver to block left silent shaft. 5. Remove oil pump sprocket nut, and remove sprocket. Remove front crankshaft sprocket and flange. Note direction and order of installation for reassembly reference. 6. Remove rear timing belt tensioner assembly. Remove rear timing belt. Remove right silent shaft sprocket with spacer (if necessary). Remove rear crankshaft sprocket with key Installation 1. Install rear crankshaft sprocket and flange. Install right silent shaft sprocket and spacer. Spacer should be installed with chamfered end into oil seal. Align timing marks. See Fig. 5 . 2. Install rear tensioner. Hold tensioner tightly against belt while tightening bolts. Ensure deflection is .20- .28″ (5.0-7.1 mm). See Fig. 6 . Install camshaft sprocket. Tighten camshaft sprocket bolt to specification. See TORQUE SPECIFICATIONS . 3. Install front timing belt tensioner, tension spring and spacer. Ensure spring is properly engaged against water pump case. Rotate tensioner toward water pump, and temporarily tighten bolts. Ensure timing marks are aligned. See Fig. 5 . Install timing belt on crankshaft. 4. Apply pressure on tension side of timing belt while installing belt (in order) on crankshaft, oil pump and camshaft sprockets. Loosen tensioner to apply spring pressure to timing belt. 5. To apply tension to belt, rotate crankshaft clockwise until camshaft sprocket timing mark is offset by 2 teeth. Tighten tensioner bolt. Tighten tensioner spacer nut

Related Content:

04 volvo s60 2 5t how to align cam shafts to cam sprockets, adjusting cam sprockets, chrysler sprocket removal tool, ej25d enigine TORQUE, what are torque values for 2 2ecotec cam sprokets

2004 Mitsubishi Lancer O-Z Rally TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 06-06-2012

download
Fig. 79: Aligning Timing Belt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry it fully back in the direction of the arrow. 4. Temporarily tighten the tensioner pulley bolt. 5. Remove the timing belt. Fig. 80: Tightening Tensioner Pulley Bolt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. INSTALLATION SERVICE POINTS >> A << TIMING BELT INSTALLATION CAUTION: If the timing belt is to be re-used, use chalk to mark (on its flat side) an arrow indicating the clockwise direction. CAUTION: After installing the timing belt, try to rotate the camshaft sprocket in the reverse direction. Recheck to be sure that the belt is fully tensioned and that each timing mark is in the proper position. 1. With the timing belt tensioner pulley bolt loosened, use a screwdriver to pry the tensioner pulley as close to the engine mount as possible. Then temporarily tighten tensioner bolt. Fig. 81: Adjusting Timing Belt Tensioner Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Align each of the camshaft and crankshaft sprocket timing marks. 3. Install the timing belt in the following order, while making sure that the tension side of the belt is not loose. 1. Crankshaft sprocket 2. Water pump sprocket 3. Camshaft sprocket 4. Tensioner pulley >> B << TIMING BELT TENSION ADJUSTMENT 1. Initially loosen the fixing bolt of the tensioner pulley fixed to the engine mount side by 1/4-1/2 turn, and use the force of the tensioner spring to apply tension to the belt. 2. Turn the crankshaft in the proper rotation direction (clockwise) for two rotations, and recheck to be sure that the timing marks on each sprocket are aligned.

Related Content:

2005 mazda 3 2 3l push rod clearance, manual book 1G FE throtle sensor, P0087 Mitsubishi cante, p0404 mitsubishi canter, p2263 mitsubishi canter

2003 Lexus ES 300 TIMING BELT Removal And Installation Manual

0

Filed Under (Lexus Manuals) by admin on 04-07-2012

download
TIMING BELT Removal (ES 300) 1. Raise and support vehicle. Remove right side front wheel. Remove right fender apron seal. Remove accessory drive belts. Lower vehicle. Disconnect engine coolant reservoir hose from water outlet. Disconnect ground strap connectors. 2. Remove engine moving control rod and engine mounting bracket No. 2 (right side), located near timing belt cover. Remove generator-to-engine bracket for access to timing belt covers. 3. Using Pulley Holder (09213-54015) or equivalent and Handle (09330-00021) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. Using puller, remove crankshaft pulley. Remove No. 1 and No. 2 timing belt covers and gaskets. See Fig. 1 . Remove transverse engine mounting bracket from front of engine. Note direction of timing belt guide installation for reassembly reference. Remove timing belt guide. 4. Temporarily install crankshaft pulley bolt and washer in crankshaft. Using crankshaft pulley bolt, rotate crankshaft clockwise until timing mark on crankshaft sprocket aligns with timing mark on oil pump body. See Fig. 2 . 5. Ensure timing marks on camshaft sprockets are aligned with timing mark on No. 3 timing belt cover. See Fig. 2 . If timing marks are not aligned, rotate crankshaft clockwise one full revolution (360 degrees). Remove crankshaft pulley bolt. 6. If reusing old belt, ensure there are 3 installation marks and front arrow marked on belt. See Fig. 3 . If not, place mating mark on belt where it contacts the crankshaft and camshaft sprockets. Also, mark belt with arrow showing direction of rotation. 7. Alternately loosen 2 bolts, and remove timing belt tensioner and dust boot. DO NOT hold tensioner with push rod facing downward. Remove timing belt in the following sequence: No. 1 idler pulley, right camshaft sprocket (firewall side), No. 2 idler pulley, left camshaft sprocket (front of vehicle side), left camshaft sprocket (front of vehicle side), water pump pulley, then crankshaft sprocket

Related Content:

2003 santa fe 2 7 timing belt marks, where is the air flow meter on a kb300 lx pdf, 2003 2 4 santa fe out two teeth on intake cam for timing rough idle, 2003 lexus 3 0camshaft timing marks, 2003 lexus 3 0camshaft timing marks diagram, daewoo lanos sump removal, how to tighten alternator belt on a toyota 1zr, thermostat for isuzu kb 300lx

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

Related Content:

4efe head bolt torque foot pounds, 4g13 timing marks, free download Service Manual for a 1992 Toyota Truck, Toyota 5K ignition, _1987_Nissan_pickup_v6 destributer timing marks

1994 Toyota Camry DX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 22-01-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. 6. Ensure timing mark on crankshaft pulley aligns with “0″ mark on No. 1 timing belt cover. Ensure hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If hole in camshaft sprocket is not aligned with alignment mark, rotate crankshaft clockwise one full revolution. 7. Loosen No. 1 idler pulley bolt. See Fig. 1 . Move No. 1 idler pulley outward, away from timing belt as far as possible. Temporarily retighten No. 1 idler pulley bolt. Remove timing belt from camshaft sprocket. 8. Using Pulley Holder (SST 09213-54015) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. 9. Using gear puller, remove crankshaft pulley. Remove No. 1 timing belt cover and gasket. Note direction of timing belt guide installation. See Fig. 1 . Remove timing belt guide. 10. Loosen No. 1 idler pulley bolt. See Fig. 1 . Remove timing belt from crankshaft sprocket. Remove idler pulleys (if necessary).

Related Content:

96 Toyota Camry 3 0 Timing Marks, TOYOTA 4Y TIMING MARKS, toyota 7A-FE timing belt alignment marks, Toyota Camry Crankshaft Pulley Removal

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, 2002 jetta crank mark, 2003 eclipsed2 4 litre cranckshaft position sensor location, 3126 timing pin hole, 91 honda accord timing belt marks diagram, 98 eclipse rs service manual, changing timing belt 2004 kia optima EX 2 7 6 cylinder ?, how to adjust belt on 2001 kia optima, kia rio 5 2007 timming belt