Skip to content

2001 toyota camry dashboard light indicators

You search PDF repair manual about 2001 toyota camry dashboard light indicators, if there are search results will appear below. If search results do not exist, please search by others keyword.

Installing the Cyron HT-1506 LED footwell light kit in a Toyota Prius

download
Begin by removing the lower glove compartment. Release the glove compartment latch, the squeeze both sides to release the catches and drop the box out of the dash. Disconnect the damper shock on the right hand side of the box by popping the shock arm from the plastic peg. Then press together on each side of the glove compartment and pull towards you. Remove the box and set it aside. Now, remove the silver passenger air vent to the left of the glove compartment. You can do this by grabbing it from the top and bottom and pulling straight back. Alternatively, you can curl your hand around inside the glove box opening and push the assembly out from the inside. It is helpful to push it from the inside to get it started and makes it easier to remove from the outside. Now is a good time to clean out the cabin air filter. It is located in the top part of the white box shown in the center of the above picture. If it’s really dirty it’s best to replace it. They are less than $20 at the dealer, or you can make your own from a household air conditioner filter. I like to vacuum mine every 4-6 months to keep it clean, and it will probably won’t need to be replaced for a long time.
Continue disassembly of the dash to allow for routing the power and signal wires. Plan your installation as far as the routing for Cyron controller and hub wiring. At this point, you must decide where to store the controller during normal use / driving. I chose to install my controller in the “secret drawer” on the lower front part of the center console, which means running wiring underneath the carpeting between the center console and the curved panel. The simpler option that requires less wire routing is to store it in the glove box. To remove the curved panel, begin by removing the plastic Christmas tree push pin from the passenger side of the curved panel. You can remove it with a flat screwdriver or gently pull the panel straight back and the pin will come loose. The driver’s side of the curved panel is held by a metal post with a plastic catch. Once the push pin is removed, pull the panel straight back and it will pop loose. The panel is fairly easy to remove and it will pop back in place on re-assembly. Once the curved panel is loose, remove the connector from the 12v accessory socket and set the panel aside. The connector is polarized so it will only fit the accessory socket in one orientation, so there is no need to mark it.
Remove the curved panel by gently pulling straight back. It will pop lose from the dash

200-92010 Toyota Camry/ Corolla OE Fit Fog Light Install Instruction

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties. 2. Attach the ring terminal with 2 black wires to the 10mm bolt next to the relay 3. Connect the ring terminal from the relay (12v red wire) to the positive terminal of the battery 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector. Seal with 3M Silicone sealant (see picture 1) Picture 1 5. Run the fog light wire harness on the driver side of the car. Use wire ties as needed. 6. Remove dash panels 7. Mount switch into switch knockout on left side of dash 8. From inside the cabin, locate the small connector that were pushed through in step 4. It will be the grommet above the gas pedal 9. Install switch harness 10. T-tap green/black wire from fog light harness to connector E21 pin 11, light green wire (first pin on right). Connector E21 is located on the left side of the steering column (picture 2) Picture 2 11. T-Tap orange/black wire from fog light harness to connector ID pin 3, pink wire (middle third pin from left). Connector ID is left of steering wheel (picture 3) Picture 3 12. Secure with wire ties. 13. Reinstall dash panels 14. Route the fog light wire under car. 15. Remove fog light cover plates and lower splash shields on both sides 16. Insert one side of the fog light into the plastic sleeve and secure other side with supplied Phillip screws (see picture 4

2007-2010 Toyota Camry Hybrid Vehicles Potential Floor Mat Interference with Accelerator Pedal

download
The owner notification will commence in early February, approximately one week after your dealership has been notified. This campaign will be launched in phases. • The first phase will include certain 2007 through 2010 model year Camry and Camry Hybrid vehicles equipped with Denso accelerator pedals. These owner letters will be mailed over a period of several weeks. • Additional models, including Camrys equipped with a CTS accelerator pedal will be launched in later phases as the remedy is developed. • Information on additional phases related to Camry (equipped with a CTS accelerator pedal), Avalon, Corolla, Highlander, Matrix, Prius, Tacoma, Tundra and Venza will be provided prior to the launch of these phases. If your dealership is contacted by an owner of a Denso pedal equipped Camry who has not yet received a notification, please verify eligibility by confirming through Dealer Daily/TIS prior to performing repairs . Dealers should perform the repair as outlined in the attached Technical Instructions. 2. Vehicles in Dealer Stock • As required by Federal law, dealers are not to deliver any new vehicles in their inventory, which are involved in a safety recall unless the defect has been remedied. However, because this defect does not exist in vehicles in which the driver’s side floor mat is compatible with the vehicle and properly secured you may continue to sell new vehicles (with Denso pedals) that have not received the full remedy if you assure the driver’s position floor mat is semi-permanently secured or place the front driver’s and passenger’s floor mats in the trunk on any vehicles in stock prior to sale or lease. Vehicle safety recall completion can be verified through TIS. • In order to assure established customers receive priority for the safety recall, we request that this campaign remedy be performed on in-stock Camry and Camry Hybrid vehicles just prior to vehicle delivery where possible. • A VIN list containing vehicles in dealer stock will be provided shortly

2004 Toyota Camry Disc Brake System Service/ Repair Manual

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

2001-2007 Toyota Highlander MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS

download
This bracket kit fits the 2001-10 Toyota Highlander. For the ’01-’07 Toyota Highlander, follow the instructions below. For ’08-’10 Toyota Highlander instructions, see the separate section included in these instructions. Important: please use all supplied bolts and parts and read all instructions carefully before beginning this installation. The majority of questions you may have can be answered within the text, and proper installation will ensure safe and secure travel. Now, begin the installation. Fig.C Fig.D Fig.E 1. Start by removing four plastic fasteners that attach the grille to the core support (Fig.C). 2. Once all the fasteners are removed, squeeze and push out a square plastic clip fastener for the grille, located between the headlight housing and the radiator support frame on each side. 3. Pull back the grille and remove the Phillips screw that attaches the fascia to the hood latch support (Fig.D). 4. On each side, remove three plastic fasteners: two of the plastic fasteners are attaching the fender liner to the fascia (Fig.E); the other plastic fastener is attaching the fender liner to the frame rail (Fig.F) 5. Remove ten 10mm (head) bolts (Fig.G) and two plastic fasteners (Fig.H) attaching the lower splash shield to the fascia and the sub frame. 6. On both sides, pull back the fender liner and remove one 10mm screw attaching the corner of the fascia to the fender (Fig.I). Fig.K Plastic fastener MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 1-800-669-9690 fax 360-735-9300 KIT# 1180-1 05/14/10 KS 9. Remove the foam shock absorption core by pulling forward (Fig. L). Note: this will not be reinstalled. Retain the foam shock absorption core and attachment hardware so that it can be replaced if the bracket is ever removed. 10. Remove six 14mm (head) bolts to remove the bumper core (Fig.M). Note: this will not be reinstalled. Retain the bumper core and attachment hardware so that it can be replaced if the bracket is ever removed. 11. Remove the alignment studs at the end of each frame rail (Fig.N). 12. Now, place the main receiver brace into the ends of the frame rails (Fig.O). 13. Bolt the main receiver brace into place using the three supplied 10mm x 1.25 x 35mm bolts, flat washers and lock washers (Fig.P). Repeat for the other side. Tighten to the torque specifications listed at the end of these instructions.