Skip to content

2001 toyota highlander stereo wiring diagram

You search PDF repair manual about 2001 toyota highlander stereo wiring diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

2001 Toyota Highlander Sport Utility, Radio, FRONT DOOR SPEAKER INSTALLATION MANUAL

download
2001 Toyota Highlander Sport Utility PRELIMINARY: Disconnect the negative battery cable. ANTENNA: The factory antenna is located atop the right front fender panel. RADIO REMOVAL AND IN-DASH INSTALLATION: Note: The factory radio provision is for a Double ISO/DIN style radio. An installation kit is required when installing an aftermarket stereo. 1. Using panel removal tool carefully pry off radio bezel. 2. Extract (6) 10 mm bolts securing radio and climate controls in dash, disconnect and remove. 3. Extract (8) Iso screws securing radio to bracket. 4. Extract (2) Philips screws securing bracket to bezel, pull away and remove radio. FRONT DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 1 ½” tweeter and a 6 ½” 3-Hole speaker mounted to a factory speaker adapter. 1. Remove screw cover from door opener cup and exract (1) Philips head screw, pry bezel out then forward to remove. 2. Remove inside mirror cover. 3. Pry out door cup and extract (1) Philips screw from beneath. 4. Exract (1) plastic fastener from front top portion of door. 5. Pry off door panel, pull away, disconnect, and remove. 6. Extract (3) 10 mm bolts securing speaker, pull away, disconnect, and remove. REAR DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 5 ¼” 3-Hole speaker mounted in a factory speaker adapter. 1. Remove screw cover from door opener cup and extract (1) Philips head screw, pry bezel out then forward to remove. 2. Pry out door cup and extract (1) Philips screw from beneath. 3. Pry off door panel, pull away, disconnect and remove. 4. Extract (3) 10 mm bolts securing speaker , pull away, disconnect, and remove

2001-2007 Toyota Highlander MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS

download
This bracket kit fits the 2001-10 Toyota Highlander. For the ’01-’07 Toyota Highlander, follow the instructions below. For ’08-’10 Toyota Highlander instructions, see the separate section included in these instructions. Important: please use all supplied bolts and parts and read all instructions carefully before beginning this installation. The majority of questions you may have can be answered within the text, and proper installation will ensure safe and secure travel. Now, begin the installation. Fig.C Fig.D Fig.E 1. Start by removing four plastic fasteners that attach the grille to the core support (Fig.C). 2. Once all the fasteners are removed, squeeze and push out a square plastic clip fastener for the grille, located between the headlight housing and the radiator support frame on each side. 3. Pull back the grille and remove the Phillips screw that attaches the fascia to the hood latch support (Fig.D). 4. On each side, remove three plastic fasteners: two of the plastic fasteners are attaching the fender liner to the fascia (Fig.E); the other plastic fastener is attaching the fender liner to the frame rail (Fig.F) 5. Remove ten 10mm (head) bolts (Fig.G) and two plastic fasteners (Fig.H) attaching the lower splash shield to the fascia and the sub frame. 6. On both sides, pull back the fender liner and remove one 10mm screw attaching the corner of the fascia to the fender (Fig.I). Fig.K Plastic fastener MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 1-800-669-9690 fax 360-735-9300 KIT# 1180-1 05/14/10 KS 9. Remove the foam shock absorption core by pulling forward (Fig. L). Note: this will not be reinstalled. Retain the foam shock absorption core and attachment hardware so that it can be replaced if the bracket is ever removed. 10. Remove six 14mm (head) bolts to remove the bumper core (Fig.M). Note: this will not be reinstalled. Retain the bumper core and attachment hardware so that it can be replaced if the bracket is ever removed. 11. Remove the alignment studs at the end of each frame rail (Fig.N). 12. Now, place the main receiver brace into the ends of the frame rails (Fig.O). 13. Bolt the main receiver brace into place using the three supplied 10mm x 1.25 x 35mm bolts, flat washers and lock washers (Fig.P). Repeat for the other side. Tighten to the torque specifications listed at the end of these instructions.

1992 Toyota Cressida Wiring Diagram

download
tem Wire ColorPolarity Wire Location 12V white – white/red Positive (+) steering column Starter black/white Positive (+) steering column Starter 2 none Ignition black/yellow Positive (+) steering column 2nd Ignition black/red Positive (+) steering column 3rd Ignition none Accessory blue/red Positive (+) steering column Accessory 2 none Tachometer black/yellow check conn(ig-) Power Door (Lock) Wiring Diagram for [ Negative (-) ] Door Lock green/red Negative (-) pass kick or theft ecu Power Door (Unlock) Wiring Diagram for [ Negative (-) ] Door Unlock green/whiteNegative (-) pass kick or theft ecu Door Trigger red/white Negative (-) theft ecu[1] Dome Supervision Wiring Diagram for [ none ] Dome none none none Headlights red/yellow Negative (-) steering column Parklight Positive green Positive (+) dimmer controll or dkp Parklight Negative green/whiteNegative (-) steering column Wipers blue/black Positive (+) steering column Left Front Window (Up/Down) grn/wht – red/blu in drivers door Right Front Window (Up/Down) pnk/blk – pnk in drivers door or dkp Left Rear Window (Up/Down) red – red-yel A in drivers door or dkp Right Rear Window (Up/Down) grn/blk – red/blk A in drivers door or dkp Trunk/Hatch Pin red/white Negative (-) at light, or theft ecu Hood Pin tied with doors Trunk/Hatch Release Wiring Diagram for [] Trunk/Hatch none Factory Alarm (Arm) arms with lock Factory Alarm (Disarm) disarms with unlock Horn white/red Negative (-) st.column or theft ecu Brake green/black Positive (+) brake switch Door Motor (Lock) none none none Door Motor (Unlock) none none none

2008 TOYOTA HIGHLANDER TRAILER WIRE HARNESS Preparation

download
1. Supplemental Restraint System (SRS) (a) Failure to carry out procedures listed below could result in possible deployment of airbag, personal injury, or unnecessary repairs to SRS. (b) Turn the key switch to the LOCK position. (Fig. 1-1) (c) Remove the key from the ignition switch. (d) Disconnect the negative battery cable. (Fig. 1-2) (e) Never use a voltmeter to troubleshoot any of the harnesses or connectors to the SRS. Accidentally probing the connectors to the SRS can lead to deployment of the airbag. (Fig. 1-3) (f) SRS wire harness loom/cover is bright yellow in color. Fig. 1-1 Fig. 1-2 Fig. 1-3 10 mm socket
TOYOTA HIGHLANDER 2008 – TRAILER WIRE HARNESS Procedure Page 5 of 16 pages Issue: A 04/13/07 2. Wiring Precautions (a) DO NOT pull on vehicle wires and/or wire harness. To uncouple electrical connectors, pull only on the connector. (Fig. 2-1) (b) Use nylon ties and adhesive foam strips to secure the vehicle harness and the trailer wire harness. (c) Ensure that all wires are properly insulated from ground. (d) When installing the trailer wire harness, make sure it is not cut or perforated by any sharp metal objects. 3. General Practices and Procedures (a) Before starting installation, refer to the supplemental restraint system procedures in Section 1 above. (b) Take care not to scratch any part of the vehicle. Bind the tips of tools (clip remover, slot screw driver, etc.) with vinyl tape to prevent damage to any part of the car, or use a nylon removal tool (resin based prying tool). (Fig. 3-1) (c) Use a small parts container to store removed bolts and tapping screws so that they can be reassembled correctly. (d) Ensure that seat/floor protectors are in position. (e) After fastening plastic ties, clip away all the excess of the ties using diagonal pliers. (Fig. 3-2)

2000-2006 TOYOTA TUNDRA VEHICLE WIRING INFORMATION

download
WIRING INFORMATION: 2000 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 2001 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Doo