2002 buick century purge solenoid valve

You search PDF repair manual about 2002 buick century purge solenoid valve, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2002 buick century purge solenoid valve Direct Download speed 5432 Kb/s

  2002 buick century purge solenoid valve Full Version speed 8172 Kb/s



1984-1995 Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System Repair Manual

0

Filed Under (Honda Manuals) by admin on 22-04-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum. When servicing or repairing any part of the emissions system, it is absolutely essential to check for any obvious mechanical faults or failures. Remember, a trouble code only indicates which sensor or circuit is affected by the problem. Simple mechanical faults such as a vacuum leak or poor electrical connection can cause a fault code. The EGR valve is not simply open or closed but is modulated by controlling the amount of engine vacuum to the valve diaphragm, up to a maximum of 8 in. Hg of vacuum. The EGR valve has a sensor in the top of the valve that reports valve lift to the ECU (same as ECM, 1992-95). The ECU modulates the position of the control solenoid valve to control the EGR valve lift according to an internal program. Upstream of the control solenoid valve, the CVC provides a constant supply of vacuum so EGR control is precise under all manifold vacuum conditions

Related Content:

2004 honda purge control valve, 2008 hyundai elantra purge valve, c230 2005 removing pcv valve and hoses, clean egr valve lincoln, where is the pcv valve on chevy cruze, where is the pvc valve located on a 2008 toyota tundra, 2007 implala vent solenoid replacement, egr valve chevy trailblaxer 2005, fuel purge valve for 2006 chevy impala, pvc valve for 2001 merc sable 24 valve overhead cam

2008 Ford Focus A/T Main Control Valve Body Removal And Installation

0

Filed Under (Ford Manuals) by admin on 01-07-2012

download
Disassembly 12 7Z490 Separator plate and gasket assembly 1. Remove the solenoid body bolts and the 13 7A101 Body — control valve lower solenoid body. 14 7R294 Stop — main regulator valve 15 7F445 Retainer plate — main regulator valve 16 7A270 Spring — main fluid pressure regulator valve 17 7C338 Valve — main fluid pressure regulator 18 7G411 Spring — solenoid regulator valve 19 7H392 Valve — solenoid regulator valve 20 7D400 Spring — intermediate servo accumulator 21 7D398 Piston — intermediate servo 2. Remove and discard the solenoid body gaskets. accumulator 22 7G408 Valve — converter pressure relief 23 7G316 Spring — converter regulator valve 24 7M040 Valve — lock up control 25 7Z490 Gasket — solenoid body 26 7G179 Valve — low reverse shift 27 7M040 Valve — 3-4 shift 28 7H148 Shift Solenoid B (SSB) (on/off) valve 29 7H148 Shift Solenoid A (SSA) (on/off) valve ISASSEMBLY AND ASSEMBLY (Continued) 3. Remove and discard the seals. 3. Install the seals. 4. Disassemble the main control valve body. 4. Install a new solenoid body gasket. Assembly 1. Install a new separator plate and gasket assembly. 2. NOTE: Do not fully tighten the bolts at this stage. Assemble the main control valve body and loosely install the bolts. DISASSEMBLY AND ASSEMBLY (Continued) 5. Install the solenoid body and loosely install the 6. Tighten the solenoid body bolts in the sequence bolts. shown. •Tighten to 9 Nm (80 lb-in)

Related Content:

5R55E Valve Body manual, diagram for torque converter clutch for 2000 Venture, valve body torque specs chevy venture, how to chane the vent valve solenoid in 2008 gmc yukon, 2007 torqshift valvebody removal, how to change the vent valve seliod on a 2008 gmc, 2003 trailblazer valve body, exploded view toyota A650E valve body, free 5r55e valve body transmission gasket replacement instructions for 2001 ford explorer, how to remove sl2 bellhousing without removing valve body

1994 Toyota Paseo ENGINE IDENTIFICATION/ VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Toyota Manuals) by admin on 12-11-2011

download
1) Disconnect PCV hose, necessary electrical connections and spark plug wires to access valve cover. Remove nuts, seal washers, valve cover and gasket. 2) Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. Ensure timing mark on crankshaft pulley aligns with “0″ mark on timing belt cover. 3) Ensure valve lifters on cylinder No. 1 are loose and valve lifters on cylinder No. 4 are tight. If conditions are not as described, rotate crankshaft clockwise one complete revolution (360 degrees). 4) Using feeler gauge, measure valve clearance between valve lifter and camshaft on intake valves of cylinders No. 1 and 2, and exhaust valves of cylinders No. 1 and 3. Record valve clearance. Rotate crankshaft clockwise one complete revolution (360 degrees). 5) Measure and record valve clearance on intake valves of cylinders No. 3 and 4, and exhaust valves of cylinders No. 2 and 4. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. VALVE CLEARANCE SPECIFICATIONS TABLE (1) Application In. (mm) Exhaust Valve ………….. .012-.016 (.31-.41) Intake Valve …………… .006-.010 (.15-.25) (1) – Adjust valve clearance with engine cold. 6) If valve clearance requires adjustment, rotate camshaft so lobe on valve to be adjusted is facing upward, away from valve lifter. Position notch area on valve lifter toward inside of cylinder head. DO NOT align notch area with camshaft. Use Valve Clearance Adjuster (SST 09248-55040) to adjust valve clearance. 7) Using SST “A” of valve clearance adjuster, push downward on valve lifter. Place SST “B” between camshaft and valve lifter. See Fig. 2. Ensure enough clearance exists for adjusting shim removal. Remove SST “A”. Fig. 2: Adjusting Valve Clearance Courtesy of Toyota Motor Sales, U.S.A., Inc. 8) Using small screwdriver and magnet, remove adjusting shim. Measure and record thickness of removed shim. Using measured clearance and adjusting shim thickness, select proper replacement adjusting shim. See Figs. 4 and 5. 9) Install replacement adjusting shim. Recheck valve clearance. Apply sealant at indicated valve cover sealing areas on cylinder head. See Fig. 3. 10) Using NEW gasket, install valve cover and sealing washers. Install and tighten nuts to specification. See TORQUE SPECIFICATIONS. To install remaining components, reverse removal procedure. NEW SHIM THICKNESS TAB

Related Content:

toyota 4af valve clearance, how to replace the perge valve on a Saturn Vue, lifter replacement 2004 avalanche 5 3 engine, REPAIR MANUAL FOR KANCIL ENGINE PDF, yhs-ddc_bd, perodua kancil valve clearen instraction pdf, 2012 chevy cruze pcv valve, 4m51 engine valve clearance, 2010 Honda Accord valve cover Torque Specs, 2006 toyota tacoma 4 cyl valve cover gasket replacement

Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System OPERATION MANUAL

0

Filed Under (Honda Manuals) by admin on 28-01-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines
SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

w584a lincoln, 2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, how to change intake gasket 2007 grandprix, schematic for front brakes on 2005 Buick Rendezvous, 200lolds aleroraditor system, 2007 Chevy Colorado Gas Tank Seal replace, 2007 kia rio service manual, pontiac 2007 g6 remove radiator cover

2002 Ford Lincoln LS Valve Cover LH Workshop Manual

0

Filed Under (Ford Manuals) by admin on 20-02-2011

download
Valve Cover LH Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 3. Remove the air cleaner housing. 1. Disconnect the mass air flow (MAF) sensor electrical connector. 2. Remove the bolt. 3. Remove the housing. 4. CAUTION: To disconnect the Norma fitting, squeeze the tabs and pull straight out or damage to the fitting can occur. Disconnect the crankcase ventilation tube. 5. Disconnect the fuel hose. For additional information, refer to Section 310-00 . 6. Disconnect the evaporative emission canister purge valve hose. 7. Remove the vapor management valve (VMV) cover. SECTION 303-01B: Engine — 3.9L 2002 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/17/2001 Material Item Specification 8. Remove the VMV. 1. Disconnect the vacuum hose. 2. Disconnect the purge hose. 3. Disconnect the electrical connector and the push pin. 4. Remove the nuts and the valve. 9. Remove the exhaust gas recirculation (EGR) vacuum regulator solenoid. 1. Disconnect the electrical connector. 2. Remove the screws and the EGR vacuum regulator solenoid. 10. Remove the bracket. 1. Remove the hose. 2. Remove the bracket. 11. Position the engine wiring harness up. 12. Remove the ignition coil cover. * Inspect the gasket and install a new gasket as necessary.

Related Content:

02 ls fuse diagram, 2002 lincoln ls repair manual pdf, 2002 lincoln ls wiper fuse location, 2005 v6 lincoln ls diagram for fuse box and relays, ecm for lincoln ls 2002 v8, hays repair manual 2002 lincoln ls, PURPOSE OF A VAPOR MANAGEMENT VALVE

1996 Ford Taurus Transmission and Drivetrain Automatic Transmission/Transaxle Removal and installation Manual

0

Filed Under (Ford Manuals) by admin on 20-04-2012

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve. Zoom Sized for Print Oil Pump And Valve Body Bolt Tightening Sequence

Related Content:

can a 2002 taurus transmission be removed without removing subframe, CLEAN THROTTLE BODY CHEVY ENVOY, how to replace the bumper cover on a 1998 Isuzu Rodeo, 03 Chevy impala removing valve cover, volvo xc90 2 9 rocker cover removal, valve cover gaskets on 2002 Escape V6, Removing Valvebody on 722 6, remove 2003 taurus transmission lowering only one side subframe, how to removed a valve body from volvo s 70, how to remove valve cover 5 4 32v navigator

2002 BMW 325I 2.5L Air Pump Repair manual

0

Filed Under (Bmw Manuals) by admin on 05-02-2012

download
Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible. 4. Check valve on front right of cylinder head can be supplied with vacuum and visually checked for opening of valve. 5. Vacuum line from check valve to operating solenoid should also be inspected for cracks or being disconnected. Vacuum line follows right side of cylinder head to back of cylinder head to the secondary air solenoid located under left rear side of intake manifold. 6. The solenoid should allow vacuum flow to the check valve during vacuum pump operation. The solenoid is controlled directly by the engine control module and receives power during key-on-engine-off. Potential Causes: A.I.R. Check Valve Engine Control Module (ECM) Codes — Engine control module fault. Defective Secondary Air Pump Secondary Air Pump Relay Secondary Air Supply Hose Broken Vacuum Line

Related Content:

where is the secondary air pump located a 2002 rendezvouz, 2008 trailblazer air pump install, bmw 3251 secondary air system bank 2, how to test a secondary air check valve on a 2002 bmw 325i, where is the air pump on a 2002 rendezvouz, where should a check valve be located

Toyota Matrix XRS Air Intake Removal And Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 10-02-2011

download
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the mass air sensor electrical connection. 3. Remove the screw that secure the vacuum switching valve to the air cleaner. 4. Remove the stock bracket from the vacuum switching valve. 5. For 2005 and 2006 models, you need to unclip the vacuum switching valve hose from the intake tube, and remove the screw from PWM switching valve. 6. Loosen the clamps at the throttle body and at the air cleaner, then remove the stock intake tube. 7. For 2002 to 2004 models, you need to remove the EVAP OBD canister closed valve vent from the air cleaner. Then unclip the upper air cleaner, then tilt upwards to unclip the PWM vacuum switching valve and the vacuum hose. 8. For 2005 and 2006 models, unclip vacuum switching valve hoses from air box, then unclip the PWM switching valve wire harness from upper airbox. 9. Remove the upper Air cleaner. 10. For 2002 to 2004 models, loosen and remove the bolt that secure the EVAP OBD canister closed valve to the lower air cleaner. 11. Loosen and remove the three bolts that secure the lower air cleaner, then disconnect the vacuum hose from the butterfly valve. 12. Tilt the lower air cleaner upwards to unclip the wire harness. 13. Remove the lower air cleaner. 14. Loosen the battery hold down bracket. 15. Remove the bolt that secures the battery hold down bracket to the radiator core support, then remove the battery hold down bracket. 16. Remove the push clip that secures the air inlet duct to the radiator core support. 17. Loosen and remove the bolt that secures the air inlet duct to the inner fender. 18. Tilt that battery backwards, then remove the air inlet duct. 19. Reinstall the battery hold down bracket. 20. Disconnect two vacuum hoses from the vacuum switching valve. Install of Intake

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, how to check radiator fluid level pontiac grand prix, Low coolant light olds intrigue, evap sensor on 2002 suburban, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 2002 mercury sable cooling system, 2006 Envoy low idle

Related Content:

2004 honda purge control valve, 2008 hyundai elantra purge valve, c230 2005 removing pcv valve and hoses, clean egr valve lincoln, where is the pcv valve on chevy cruze, where is the pvc valve located on a 2008 toyota tundra, 2007 implala vent solenoid replacement, egr valve chevy trailblaxer 2005, fuel purge valve for 2006 chevy impala, pvc valve for 2001 merc sable 24 valve overhead cam