buick lesabre custom heater core replacement

You search PDF repair manual about buick lesabre custom heater core replacement, if there are search results will appear below. If search results do not exist, please search by others keyword.



  buick lesabre custom heater core replacement Direct Download speed 5432 Kb/s

  buick lesabre custom heater core replacement Full Version speed 8172 Kb/s



2000 Chevrolet Blazer HEATER CORE Removal And Installation Procedure

0

Filed Under (Chevrolet Manuals) by admin on 20-05-2011

download
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE . 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws Courtesy of GENERAL MOTORS CORP. 3. Remove the heater core access cover. 4. Remove the heater core from the heater/vent module. Fig. 15: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the heater core to the heater/vent module Fig. 16: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. 2. Install the heater core access cover. Tighten Tighten the heater core access cover screws to 1.9 N.m (17 lb in). NOTE: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

0

Filed Under (Buick Manuals) by admin on 04-02-2012

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

Related Content:

buick terraza hub removal, 2005 buick century code p0455, hunter 9700 user manual, 2000 buick lesabre custom manual, how to change the lower control arms on a 2005 Titan pdf, hunter lift L401, integrated wheel end FOR F150, location of fuses and relays 2003 buick park avenue, Rear Tire wear Mecury Mariner, repair manual on 2001 cadi deville on motor mount

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

HONDA Front Seat Belt Replacement Warranty Policy

0

Filed Under (Honda Manuals) by admin on 24-11-2011

download
CUSTOMER INFORMATION : The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your car. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your car, or that your car has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. ? 1996 American Honda Motor Co., Inc. – All Rights Reserved . ATB 14788-17665 (9601) 1 of 2 JAN 22, 1996 92-012 BODY ALL 1986 and later Applicable To Model File U nder Issu e D ate Bulletin N o. Service Bulletin Front Seat Belt Replacement Warranty Policy (Supersedes 92-012, dated March 13, 1992) Warranty policy for front seat belt replacement is to replace either the belt/retractor mechanism or the buckle when either does not work properly. Warranty covers the replacement of the failed half of a belt, not the entire assembly (see PARTS INFORMATION ). NOTE: For 1970 through 1985 models, seat belts are replaced as a complete assembly under a separate warranty policy. COMPONENT REPLACEMENT Front seat belts are made by several suppliers, and some are sold as individual components (two separate halves); they are not stocked as a complete set. Therefore, whenever you replace a belt, make sure the new belt half is the same type and from the same manufacturer as the original – otherwise, the belt may not buckle properly. To determine the manufacturer and type (or “model”) of the belt, look for the white tag on the original belt in the car. The tag is on the retractor side of the belt (visible at the lower attachment point), or on the belt if you pull the belt all the way out. From the tag, mark down the manufacturer’s name (either Nippon Seiko K.K. or Takata), the belt “model” number and the date of manufacture. If the tag is missing or illegible, look on the buckle component for the name Nippon Seiko K.K. or the stylized “T” mark () for Takata. NOTE: Some belts may have NSK Warner K.K. as the manufacturer’s name. Use Nippon Seiko K.K. belts as the replacement. Take the information to your Parts Department to order the proper replacement belt. NOTE: For more information on seat belts and seat belt related items read: -Twisted Seat Belt (ServiceNews, July ’85) -Seat Belt Testing and Repair (Service Bulletin 86-014, August ’86) -Automatic Seat Belt Troubleshooting (ServiceNews, May ’89) -Lap Belt Retracts Slowly (Service Bulletins 90-003, January ’90 and 90-012, April ’90) -Torn Seal on Seat Belt Track (Service Bulletin 91-004, March ’91) -Slow to Retract Seat Belt, Cleaning the Guide Ring (ServiceNews, April ’91) -Accord Shoulder Belt System Wire Colors (ServiceNews, May ’91) -Seat Belt Slow to Retract (Service Bulletin 91-030, December ’91) Refer to your Service Bulletin Index and the ServiceNews Index for model specific information. Most repairs do not require seat belt component replacement. PARTS INFORMATION For front seat belt replacement ordering information and availability, contact your parts center.

Related Content:

1986 chevy c10 new belt, installing new rotors on a 1992 ford f250 4wheel drive, volvo 850 repair seat belt tensioner manual download, 2004 chevy malubu surpupten belt replacement on a 2 2 liter on you tube, 2002 chevy malibu passlock gm bulletin, sun visor repairs 2013 honda accord, snugtop glass button bolt, replace sun visor 09 honda accors, repairing seat belt in dodge dakota, 1990 HONDA CIVIC SEATBELT FUSE BLOCK

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to change evaporator core on 1998 blazer, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, Ford Expedition heater core instructions, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

Toyota LandCruiser 4.2TD Timing belt replacement intervals

0

Filed Under (Toyota Manuals) by admin on 02-03-2012

download
Timing belt replacement intervals The information relating to timing belt replacement intervals is additional to the main purpose of this CD, but is included to provide guidance to garages and for customer advice. Where possible the recommended intervals have been compiled from vehicle manufacturers’ information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully later in this section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. 5. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due. 6. If the belt does fail, have you considered the consequences. If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. 7. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. 8. If in doubt about the condition of the belt – RENEW it. 9. Removal Removal Remove timing belt cover [1]. 1. Turn crankshaft clockwise until timing marks aligned [2]. 2. Ensure timing marks aligned: 1KZ-T/TE: [3]. 3. 4. Remove: Automatic tensioner unit [6]. Tensioner pulley bolt [7]. Tensioner pulley [8]. Timing belt. 5. Installation Installation Check tensioner pulley for smooth operation [8]. Replace if necessary. 1. Remove dust cover. Check tensioner body for leakage or damage [6]. Check pushrod protrusion is 9,0-9,8 mm [9]. 2. Check pushrod does not move when pushed against a firm surface. If pushrod moves: Replace automatic tensioner unit. 3. Slowly compress pushrod into tensioner body until holes aligned. Use press. 4. Retain pushrod with 1,5 mm Allen key through hole in tensioner body [10]. Fit dust cover. 5. Ensure timing marks aligned [2]. 6. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 7. Fit timing belt in anti-clockwise direction, starting at lower sprocket. Ensure belt is taut between sprockets. 8. Fit tensioner pulley [8]. Tighten bolt to 34 Nm [7]. 9. Push tensioner pulley against belt. Install automatic tensioner unit [6]. Tighten bolts evenly to 13 Nm [5]. 10. Remove Allen key from tensioner body to release pushrod. 11. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3] or [4]. 12. If not: Repeat installation and tensioning procedures. 13. Install components in reverse order of removal. 14. Reset timing belt replacement warning lamp as follows: 15. -Runner/Landcruiser: Remove grommet in speedometer housing. Depress switch using a thin screwdriver [11]. 16. Colorado: Remove speedometer housing. Remove screw indicated and insert in alternative location [12]. 17. Amazon: Lamp illuminates at 90,000 miles. Return vehicle to dealer.

Related Content:

mazda bt50 timing belt replacement, 4 7L Toyota Timing Belt Replacement, Kia 3 5 Timing Belt Replacement, honda odyssey timing belt replacement mileage, 2004 subaru forester XT timing you tube instalation, Timing Belt Replacement Intervals Pontiac, how often change timing belt 2011 chevy malibu, how to change a timing belt on a 2011 kia soul, how to install varable timing solenoid on gmc envoy xuv 4 2l, how to remove a three bolt crankshaft pulley mazda bt 50

1994 Ford Mustang A/ C Evaporator Housing Removal and Installation

0

Filed Under (Ford Manuals) by admin on 03-06-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01 . If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side) . 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment.

Related Content:

acadia remove center console panel, remove center console 2002 pontiac grand prix, how to remove center console 2001 ford escort, howtoremovecenterconsolefrom2007malibu, how to tighten the overhead console laredo, 2000 corolla shift knob, how to take a part 2007 toyota tundra center console, how to replace center console lid on toyota tundra, HOW TO REMOVE THE CENTER CONSOL COVER ON A 2011 HONDA ACCORD, remove 2005 rav4 console

2000 Ford Crown Victoria/Grand Marquis Evaporator Core Housing Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 03-07-2012

download
Evaporator Core Housing Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Recover the refrigerant. For additional information, refer to Section 412-00 . 3. Drain the radiator so that the coolant level is below the heater core. For additional information, refer to Section 303-03 . 4. Raise the vehicle. For additional information, refer to Section 100-02 . 5. Remove the RH front wheel and tire. 6. Remove the screws from the RH fender apron and remove the fender apron. 7. Remove the nuts. 8. Lower the vehicle. 9. Remove the blower motor switch resistor. For additional information, refer to Section 412-04 . 10. Disconnect the connector. 11. Disconnect the evaporator to compressor suction line from the suction accumulator drier. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 12. Disconnect the condenser to evaporator tube from the A/C evaporator core inlet tube. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 13. Remove the nuts and position the purge valve and backet away from the evaporator core housing. 14. Remove the heater hoses from the heater core. 15. Disengage the connectors fom the bracket. 16. Disconnect the connector. 17. Remove the nut and reposition the wire harness away from the evaporator housing. 8 18. Disengage the harness from the bracket. 19. Remove the pin-type retainer and clip and remove the instrument panel lower insulator. 20. Fold back the carpet and remove the screw. 21. Inside the vehicle, remove the screw. 22. Remove the nuts(engine side).

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre