Skip to content

2002 chevy 4 3 fuel pressure specs

You search PDF repair manual about 2002 chevy 4 3 fuel pressure specs, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Chevrolet Chevy Suburban – 4WD Intake Manifold Replacement Manual

download
Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly. 1. Remove the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 2. Remove the fuel injectors. Refer to Fuel Injector Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 3. Disconnect the following electrical connectors: 4. Remove the knock sensor harness electrical connector from the intake manifold. 5. Set the electrical harness aside. <- Back Forward -> Document ID# 738735 2002 Chevrolet Chevy Suburban – 4WD Print – Manifold absolute pressure (MAP) sensor (1) – Knock sensor (2) – Exhaust gas recirculation (EGR) valve, if equipped. 6. If equipped, remove the following EGR pipe bolts: 7. If equipped, remove the EGR pipe with valve. 8. If equipped, remove the EGR pipe gasket from the exhaust manifold If equipped with vacuum assisted brakes, remove the vacuum brake booster hose from the rear of the intake manifold.

1998-2000 HONDA Accord L4 Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A M/T WITH CRUISE CONTROL 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. Zoom Sized for Print 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. Zoom Sized for Print 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. . Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. Zoom Sized for Print 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A

2001 Ford F-150 Draining-Coalescer/ Pressure Relief-Natural Gas Bi-Fuel System Repair Manual

download
1. Relieve the Bi-fuel system fuel pressure. For additional information, refer to Pressure Relief—Natural Gas Bi-Fuel System. 2. Raise the vehicle on the hoist. For additional information, refer to Section 100-02. 3. NOTE: There is an O-ring attached to the drain plug. The O-ring must be replaced each time the drain plug is removed. Remove the drain plug. 4. Install the drain plug. 5. Lower the vehicle. 6. Pressurize the fuel system. WARNING: It is important that your bi-fuel vehicle be correctly maintained by Ford bi-fuel trained personnel. If a concern occurs, it is important that correctly trained personnel diagnose the cause. If a concern relates to the fuel system, correct part replacement is imperative to keep your vehicle operating at normal performance. Bi-fuel components and gasoline specific components are not interchangeable. If your vehicle is not serviced in accordance with bi-fuel service procedures, damage can occur and your warranty may be invalidated. WARNING: Fuel supply lines are always pressurized. When servicing fuel related components, do not smoke or carry lighted tobacco or an open flame of any type. Flammable mixtures may be present and can ignite, resulting in personal injury. WARNING: The natural gas fuel system is always pressurized to 655 kPa (95 psi) downstream of the fuel pressure regulator and up to 24821 kPa (3,600 psi) upstream of the fuel pressure regulator. Use care when servicing the fuel system or personal injury can occur. WARNING: The natural gas fuel supply manifold is pressurized to 655 kPa (95 psi). Fuel pressure must be relieved prior to any fuel system service. WARNING: The fuel system pressure must be relieved before any component can be removed. The fuel tanks must be evacuated prior to tank removal. Removal of components without pressure relief or tank evacuation can cause natural gas to escape into the air and cause injury or death.

2002 Ford Crown Victoria/ Grand Marquis Fuel Injection Supply Manifold Workshop Manual

download
Removal All vehicles WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in personal injury. WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved. Failure to follow these instructions may result in personal injury. 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 2. Relieve the fuel pressure. For additional information, refer to Section 310-00A (Gasoline) or Section 310-00B (Natural Gas). 3. Disconnect the fuel lines. For additional information, refer to Section 310-00A (Gasoline) or Section 310-00B (Natural Gas). 4. Remove the throttle body (9E926). For additional information, refer to Throttle Body in this section. 5. On gasoline engines, remove the EGR valve to exhaust manifold tube (9D477). For additional information, refer to Section 303-08 . 6. Remove the drive belt (8620). For additional information, refer to Section 303-05 . Vehicles equipped with natural gas engines 7. Disconnect the fuel temperature sensor connector. 8. Disconnect the fuel pressure sensor connector. All vehicles 9. Disconnect the main fuel shut-off solenoid connector. 10. Disconnect the generator cable, electrical connector, and harness pin-type retainer. 11. Remove the bolts and the generator mounting bracket (10153). 12. Remove the bolts. 13. Unclip the accelerator cable (9A758) and the speed control actuator cable (9A825) from the two crash brackets and position out of the way. 14. Separate the LH heated oxygen sensor and the transmission electrical connector from the bracket at the rear of the cylinder head. 15. Separate the fuel charging wiring pin-type retainer from the crash bracket. 16. Remove the wiring bracket. * Disconnect the wiring connectors. * Separate the transmission harness from the stud. * Remove the nut and the bolt and remove the bracket 17. NOTE: On natural gas vehicles, there are no EGR vacuum connections. Disconnect the vacuum lines and position out of the way. 18. Remove bolt and stud and remove the crash bracket. 19. Disconnect the ground connector from the RH rear stud. 20. Disconnect generator harness locator retainer from LH front stud. 21. Disconnect the eight fuel injector electrical connectors

2002 Chevrolet Tahoe – 4WD Fuel Line Disconnect Tool for Fuel Filter Removal/ Installation Procedure on 5.3L Flexible Fuel Engine

download
2. Install the J 34730-1A . 3. Loosen the fuel fill cap in order to relieve fuel tank vapor pressure. 4. Open the valve on the J 34730-1A in order to bleed the system pressure. The fuel connections are now safe for servicing. 5. Drain any fuel remaining in the gauge into an approved container. 6. Once the system pressure is completely relieved, remove the J 34730-1A . 7. Raise and suitably support the vehicle. Important Clean the fuel filter connections and surrounding area before disconnecting the fuel lines in order to avoid possible fuel system contamination. 8. Using a flare nut wrench and a backup wrench, disconnect the fuel line fitting from the fuel filter. 9. Pull the quick-connect fitting back until the internal retainers hit the filter stop. 10. Twist one end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 11. Twist the opposite end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 12. Once the J 46363 – Fuel Line Disconnect Tool is inserted, ensure the tool is parallel to the filter and the fitting. 13. While holding the filter, push the quick-disconnect fitting towards the filter in order to disconnect the quick- connect fitting. 14. Remove the quick-connect fitting from the filter. 15. Remove the filter from the bracket. 16. Install the new fuel filter, P/N 15173334 or P/N 25164003 (A/C Delco P/N GF847), to the bracket. 17. While holding the filter, push the fitting towards the filter in order to connect the quick-connect fitting. 18. Using a flare nut wrench and a back up wrench, connect the fuel line fitting to the filter. 19. Position the fuel sensor bracket into place and install the two nuts. Tighten Tighten the two nuts to 17 N·m(13 lb ft). 20. Lower the vehicle. 21. Tighten the fuel cap. 22. Connect the negative battery cable.