Skip to content

2002 chevy blazer intake manifold torque specs

You search PDF repair manual about 2002 chevy blazer intake manifold torque specs, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Chevrolet Chevy Suburban – 4WD Intake Manifold Replacement Manual

download
Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly. 1. Remove the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 2. Remove the fuel injectors. Refer to Fuel Injector Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 3. Disconnect the following electrical connectors: 4. Remove the knock sensor harness electrical connector from the intake manifold. 5. Set the electrical harness aside. <- Back Forward -> Document ID# 738735 2002 Chevrolet Chevy Suburban – 4WD Print – Manifold absolute pressure (MAP) sensor (1) – Knock sensor (2) – Exhaust gas recirculation (EGR) valve, if equipped. 6. If equipped, remove the following EGR pipe bolts: 7. If equipped, remove the EGR pipe with valve. 8. If equipped, remove the EGR pipe gasket from the exhaust manifold If equipped with vacuum assisted brakes, remove the vacuum brake booster hose from the rear of the intake manifold.

2001 Chevy Truck S10/ T10 Blazer Intake Manifold Replacement (Upper) Removal And Installation Manual

download
Intake Manifold Replacement (Upper) Notes Intake Manifold Replacement – Upper Removal Procedure Important: The upper intake does not have to be removed to remove the lower intake manifold. 1. Disconnect the breather tube at the air cleaner outlet duct 2. Remove the air cleaner outlet duct retaining wingnut. 3. Disconnect the IAT sensor harness connector 4. Remove the air cleaner outlet duct from the throttle body. 5. Disconnect the accelerator cable from the throttle body 6. Remove the accelerator cable from the accelerator control cable bracket. 7. Disconnect the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. 8. Disconnect the vacuum hose from the intake manifold for the vacuum tank. 9. Remove the power brake booster vacuum hose. 10. Disconnect the following electrical connectors: * The A/C compressor clutch (1) * The A/C compressor cutoff switch (5), if equipped * The Throttle Position (TP) sensor (2) * The Idle Air Control (IAC) motor (3) 11. Disconnect the following electrical connectors: * The fuel meter body assembly (1) * The Manifold Absolute Pressure (MAP) sensor(3) * The EVAP canister purge solenoid valve (2) 12. Remove the engine wire harness clip from the accelerator cable bracket. 13. Move the engine wiring harness aside. 14. Remove the accelerator cable bracket from the throttle body and the intake manifold. 15. Remove the accelerator and cruise control cable bracket from the throttle body. Leave the accelerator and cruise control cables on the bracket16. Remove the PCV valve hose assembly from the intake manifold and the valve rocker arm cover. 17. Remove the bracket for the engine wiring harness from the intake manifold stud. 18. Remove the fuel lines from the fuel meter body assembly. 19. Remove the EVAP canister purge solenoid valve.

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

2002 Chevrolet Impala Intake Manifold Replacement (Lower) Removal And Installation Manual

download
Intake Manifold Replacement (Lower) Notes Intake Manifold Replacement – Lower Removal Procedure 1. Disconnect the negative bakery. 2. Remove the upper intake manifold. 3. Remove the left valve rocker arm cover. 4. Remove the right valve rocker arm cover. 5. Disconnect the Engine Coolant Temperature ( ECT ) sensor electrical connector. 6. Disconnect and remove the fuel injector and the Manifold Absolute Pressure (MAP) sensor wiring harnesses. 7. Remove the fuel pipe clip bolt. 8. Remove the fuel pipe clip. 9. Remove the fuel feed pipe from the fuel injector rail. 10. Remove the fuel return pipe from the fuel injector rail. 11. Remove the fuel injector rail. 12. Remove the power steering pump from the front engine cover and reposition. 13. Remove the heater inlet pipe with heater hose from the lower intake manifold and reposition. 14. Remove the radiator inlet hose from the engine. 16. Remove the lower intake manifold bolts. 17. Remove the lower intake manifold. 18. Remove the valve rocker arms and pushrods. 19. Remove the lower intake manifold gaskets and seals. 20. Clean the lower intake manifold gasket mating surfaces. 21. Remove and clean all the RTV sealant from the lower intake manifold and the engine block (1).

Chrysler V8 DUAL QUAD INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

download
PREP AND TUNING FOR POWER: NOTE: This manifold will produce optimum power and drivability when used with #1405 carburetors. Please refer to Edelbrock Performer Series Carburetor Owner’s Manual for tuning procedures. 1. Edelbrock has found, while dyno testing on a Performer level engine at our location, the best calibration to be: Metering Rods – .070″ x .047″ (stock 1405), Primary Jets – .098″ (provided with intake manifold), and Secondary Jets – .086″ (provided with intake manifold). This will vary according to engine build and atmospheric conditions. Use it as a starting point. However, if used for racing or marine installation, further tuning may be necessary. 2. Aftermarket distributor curve kits may be used with this intake manifold. A basic ignition curve of 12° to 14° initial and a total of 36° to 38° advance is a good starting point. 3. Use modified or high performance cylinder heads such as our Performer RPM. 4. Installation of aftermarket headers, camshafts or both may lean carburetor calibration. Should this condition occur, recalibrate with a richer jet. • CAMSHAFT AND HEADERS: Dual Quad manifolds are compatible with aftermarket camshafts and headers. Header primary tube diameter should be 1-7/8″, depending on the specific engine combination. Edelbrock has developed two camshafts for use with this intake manifold – Performer-Plus #2192 or Performer RPM #7194. Please check the catalog or website for rpm and application guidelines. INSTALLATION 1. Use only recommended intake gaskets set when installing this intake manifold. For ease of installation, we recommend Edelbrock Manifold Bolt and Washer Kit, #8594. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Use a factory style valley pan along with the recommended gaskets. 4. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 5. Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs