Skip to content

2002 nissan altima door actuator problems

You search PDF repair manual about 2002 nissan altima door actuator problems, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.

2002 NISSAN ALTIMA MANUAL A/C TEMPERATURE NOT ADJUSTABLE REPAIR MANUAL

download
SERVICE PROCEDURE 1. Remove the following components; • cluster lid “C” (HVAC control surround trim) • fuse box cover • driver’s side instrument panel lower cover (attached with 2 screws). 2. Remove the screw from the center of the cable operated gear (see Figure 2). Figure 2 3. Locate the small (about 1″ dia.) white air mix door gear. Hopefully it is still on the floor. NOTE: If you cannot find the old air mix door gear, order a new gear. Refer to the Parts Information section of this bulletin. 4. To see how it is supposed to fit, temporarily install the gear into the air mix door shaft (see Figure 3). Figure 3 Air mix door drive gear (shown installed) Heater box Cable operated gear Retaining screw (remove) Front TP020106 Cable (do not detach) On the left side of the heater case, remove the screw from the center of the cable operated gear for the air mix door. Note: It is not necessary to detach the cable from the gear or the heater box. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. Front TP010607a The gear can fit two different ways, only one of which is correct. Install the gear and rotate the gear/mix door shaft assembly fully clockwise so the gear’s index pin is at the 2 to 3 o’clock position. Cable (do not detach) Note: If the gear is in the correct spot, the alignment pin will be at the 2 to 3 o’clock position. POSITIONING THE GEAR CORRECTLY IS CRITICAL TO GETTING THE DOOR TIMING RIGHT. 3/5 5. Remove the gear, thoroughly clean the gear shaft of any grease, and apply the glue. See Figure 4. Figure 4 6. Re-install the gear into the mix door shaft (see Figure 5). Figure 5 TP010606a Air mix door gear (back side) Apply Glue to Shaded areas b. Apply plastic glue (3M dp-8005 or equivalent) to the shaft of the air mix door gear in the area where it inserts into the air mix door shaft. a. Thoroughly clean the air mix door gear shaft. Note: It is not necessary to clean the grease from the gear teeth. Front TP020100 Re-install the gear so the gear’s index pin is at the 2 to 3 o’clock position when the gear/mix door shaft assembly is turned fully clockwise. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. 4/5 7. Set the HVAC control temperature dial as shown in Figure 6. Figure 6 8. Re-install the cable operated gear (see Figure 7). Figure 7 9. Operate the temperature control while watching the air mix door gear movement. They should operate freely with no binding. 10.Check the adjustment of the temperature cable as follows: A. Rotate the temperature control knob to the full COLD position (i.e., fully counterclockwise) and confirm the air mix door is fully seated (sealed) in the down position, then B. Rotate the temperature control knob to the full HOT position (i.e., fully clockwise) and confirm the air mix door is fully seated (sealed) in the up position. If the air mix door does not fully seat (seal) in either the full HOT or full COLD position: • Adjust the temperature control cable, with the temperature control knob in the full hot position, using the clip at the heater unit (see Figure 7) 11.Re-install the trim pieces removed in step 1.

NISSAN ALTIMA OR SENTRA W /QR25 ENGINE NO-START AFTER COLD SOAK REPAIR MANUAL

download
SERVICE PROCEDURE Replace Starter, Add Cleaner 1. Replace the starter motor. • Use the part number from the Parts Information section of this bulletin. • Refer to section SC, “STARTING SYSTEM, Removal and Installation” in the applicable Nissan Electronic Service Manual (ESM). 2. Add one full can of Nissan In-Tank Fuel System Cleaner to the fuel. NOTE: If the fuel tank is less than ¾ full, instruct the customer to fill the tank as soon as it is convenient after the repair. Driving with the Cleaner installed and low fuel level will not harm the fuel system or engine, but will reduce the effectiveness of the cleaning process. 3. Continue to ECM Part Number Check (next page). 1. With CONSULT-II “ON”, print the Self-DIAG Results as follows: START (Nissan) >> ENGINE >> Self-DIAG Results >> PRINT SELF-DIAG RESULTS SYSTEM ENGINE DATE XX/XX/XXXX* 11:07:11 P/N 23710-XXXXX TP020389h DTC RESULTS TIME NO DTC IS DETECTED Current ECM Part Number * Example, your screen may differ. 3. Using the printout from Step 1: • Compare the vehicle’s current ECM P/N to those shown under Current ECM P/N in Chart 1, below: • This comparison will allow you to determine if the ECM needs to be reprogrammed. Chart 1, Current ECM P/N’s: VEHICLE PACKAGE NATS? CURRENT ECM P/N A/T, ASCD YES 23710-9J305, -9J003, -9J002, -9J001, -9J000, -8J001, -8J000 M/T, ASCD YES 23710-9J315, -9J013, -9J012, -9J011, -9J010, -8J061, -8J060 A/T, no ASCD YES 23710-9J300, -9J008, -9J007, -9J006, -9J005, -8J011, -8J010 02-04 Altima M/T, no ASCD YES 23710-9J310, -9J018, -9J017, -9J016, -9J015, -8J071, -8J070 YES 23710-8U542, -8U541, -8U540, -8U041, 8U040 A/T NO 23710-8U502, -8U501, -8U500, -8U001, 8U000 YES 23710-8U562, -8U561, -8U560, -8U061, -8U060 02-03 Sentra 5 M/T NO 23710-8U512, -8U511, -8U510, -8U011, -8U010 YES 23710-8U072, -8U071, -8U070 02 Sentra 6 M/T NO 23710-8U022, -8U021, -8U020 YES 23710-8U572, -8U571, -8U570 03 Sentra 6 M/T NO 23710-8U522, -8U521, -8U520 NOTE: The 2004 Sentra ECM does not need to be reprogrammed for this bulletin. A. If your vehicle’s ECM P/N matches a P/N in the chart above: • Perform ECM Reprogramming (page 4). B. If your vehicle’s ECM P/N does not match a P/N in the chart above: • ECM Reprogramming is not necessary, bulletin complete / end here

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

NISSAN Altima, Quest, Maxima MIL ON WITH P0340 / P0345 (CMP SENSOR) AND/ OR ENGINE IS HARD TO START WHEN WARM REPAIR MANUAL

download
ACTIONS: • If you only have DTC P0340, replace only Bank 1 CMP (Camshaft Position) Sensor. • If you only have DTC P0345, replace only Bank 2 CMP (Camshaft Position) Sensor. • If you have both codes, replace both sensors. • For a “hard to start warm” incident, replace both sensors, even if you have no codes. Refer to sections EC and EM in the correct Service Manual for sensor replacement information. If replacement of the sensors does not solve your incident, go back to ASIST for further diagnostic and repair information. PARTS INFORMATION DESCRIPTION PART # QUANTITY Camshaft Position Sensor- Bank 1 23731-6J906 1 Camshaft Position Sensor- Bank 2 23731-AL616 1 CLAIMS INFORMATION Submit a Primary Failed Part (PP) line claim using the following claims coding: DESCRIPTION PFP OP-CODESYSDIAFRT RPL One Camshaft Position Sensor (Bank 1 or Bank 2) (1) DE64AA AA 32 (2) RPL Both Camshaft Position Sensors (Banks 1 and 2) (1) DE67AA AA 32 0.3 hrs. (1) Reference the Parts Information table and use the indicated sensor P/N’s as the PFP. (2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT