2002 toyota sienna cv axle removal

You search PDF repair manual about 2002 toyota sienna cv axle removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2002 toyota sienna cv axle removal Direct Download speed 5432 Kb/s

  2002 toyota sienna cv axle removal Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, how to remove right front axle 95 bronco, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, Torque specs for 2008 prius axle nuts, 2002 ford expedition trailing arm torque specs, 2002 dodge dakota front differential diagram, estimate front axle seal escape, DIY LEXUS GX 470 AXLE REPLACE

1989 Toyota 4Runner ENGINE PERFORMANCE Removal Overhaul And Installation

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.

Related Content:

yhs-mystartdefault, toyota 4k carburetor manual download, remove center peice from 2011 toyota camry, how replace alternator in 2006 honda odessey, toyota sienna grill removal, jaguar fuel hose removal, 4k carburetor manual, how to check windshield wiper motor and arm on a 2007 malibut, how to remove center console 2013 camry, toyota 4k carburetor service manual

Toyota ISO Adapter Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 19-05-2011

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

Related Content:

2002 toytoa camry tank vent valve, toyota 4af engine repair manual, 1998 toyota A245E automatic transmission rebuild manual, 2002 toyota tundra 4 wheel drive suspencion, p67-y toyota vitz, 2004 toyota highlander window diagram, show prado 1999 valve attached to rear brake pipe with spring, 2009sienna v6 thermostadt extraction, diagram of front passenger seat occupant sensors and where 2005 toyota camry located, p1225 spill control circuit

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to change evaporator core on 1998 blazer, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, Ford Expedition heater core instructions, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

0

Filed Under (Land Rover Manuals) by admin on 09-01-2012

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

Related Content:

accessory drive timing marks cummins m11, 05 sport trac crank pulley tighten, camshaft bolt removal tool ford escort, how much is a camshaft pulley for 2005 mazda 6, mazda 3 crankshaft pulley broken bolt removal, montero sport how do i remove it cam seal nut, how to remove rear cargo cover in venza, how to remove pulley tensioner on a 99 mercury sable, perkins AR70498 front cover, removing a crankshaft starlet

TOYOTA AND LEXUS HIGHLANDER HYBRID REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-03-2012

download
Engine and Vehicle Identification Chart………………………………………..4-2 General Engine Specifications………4-2 Engine Tune-Up Specifications……..4-2 Capacities ………………………………….4-3 Valve Specifications …………………….4-3 Crankshaft and Connecting Rod Specifications……………………..4-3 Camshaft and Bearing Specifications ……………………………4-4 Piston and Ring Specifications……..4-4 Torque Specifications………………….4-4 Wheel Alignment ………………………..4-5 Tire, Wheel and Ball Joint Specifications ……………………………4-5 Brake Specifications ……………………4-5 Scheduled Maintenance Intervals……………………………………4-6 STEERING AND SUSPENSION ………………4-28 A Air Bag…………………………………….4-28 Disarming ……………………………4-28 Precautions ………………………….4-28 Alternator …………………………………..4-7 B Brake Caliper ……………………………4-30 Removal And Installation……….4-30 C Camshaft and Valve Lifters…………4-14 Inspection ……………………………4-16 Removal & Installation…………..4-14 CV-Joints………………………………… 4-24 Overhaul ……………………………..4-24 Cylinder Head …………………………..4-10 Removal & Installation…………..4-10 D Disc Brake Pads………………………..4-32 Removal And Installation……….4-32 E Engine Assembly ………………………..4-7 Removal & Installation…………….4-7 Exhaust Manifold ………………………4-12 Removal & Installation…………..4-12 F Front Crankshaft Seal………………..4-14 Removal & Installation…………..4-14 Front Halfshaft………………………….4-23 Removal & Installation…………..4-23 Front Strut ……………………………….4-28 Removal & Installation…………..4-28 Front Wheel Bearing………………….4-29 Fuel Filter ………………………………..4-21 Fuel Injector……………………………..4-22 Removal & Installation…………..4-22 Fuel Pump ……………………………….4-21 Removal & Installation…………..4-21 Fuel System Pressure………………..4-21 Relieving ……………………………..4-21 H Heater Core………………………………..4-7 Removal & Installation…………….4-7 Hybrid Transaxle Assembly…………4-22 Removal & Installation…………..4-22 I Ignition Timing ………………………….. 4-7 Adjustment…………………………….4-7 Intake Manifold …………………………4-11 Removal & Installation…………..4-11 L Lower Ball Joint………………………..4-29 Removal & Installation…………..4-29 Lower Control Arm……………………4-29 Removal & Installation…………..4-29 O Oil Pan…………………………………….4-18 Removal & Installation…………..4-18 Oil Pump …………………………………4-18 Removal & Installation…………..4-18 P Pinion Seal ………………………………4-27 Removal & Installation…………..4-27 Piston and Ring………………………..4-21 Positioning ………………………….4-21 Power Rack And Pinion Steering Gear…………………………..4-28 Removal & Installation…………..4-28 R Rear Halfshaft………………………….. 4-24 Removal And Installation……….4-24 Rear Main Seal…………………………4-19 Removal & Installation…………..4-19 Rear Strut…………………………………4-28 Conventional Strut Overhaul…..4-28 Removal And Installation……….4-28 Rear Traction Motor…………………..4-22 Removal & Installation…………..4-22 Rear Wheel Bearing…………………..4-29 Removal And Installation……….4-29 T Timing Belt ………………………………4-19 Removal & Installation…………..4-19 V Valve Lash ……………………………….4-17 Adjustment…………………………..4-17 W Water Pump ……………………………..4-10 Removal & Installation………..

Related Content:

how to install running boards on honda pilot, nissan ka20 16 valve cyl head gasket replacement, 2001 chevrolet monte carlo radiator removal, zx2 vct replacement instructions, 2006 sienna liftgate struts replacement video, 2002 highlander brake torque, nissan ka20 timing marks, replace alternator on honda ridgeline, quicksilver isolators pdf, whats the piece that connects to lower control arm on 1997 Buick le sabre

2002 Daewoo Leganza SE Dashboard / Instrument Panel Service and Repair Manual

0

Filed Under (Daewoo Manuals) by admin on 02-02-2012

download
Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the floor console. 3. Remove the sun sensor and the automatic temperature controls assembly. 4. Remove the tweeter speakers and the stereo cassette AM/FM radio. Refer to Section 9F, Audio Systems. 5. Remove the screws and the instrument panel storage compartment. 6. Remove the instrument cluster dimmer switch assembly. 7. Remove the instrument cluster. 8. Remove the chime module. 9. Remove the kick panels. 10. Remove the glove box. 11. Remove the screws and the glove box housing. 12. Disconnect the glove box housing electrical connectors. 13. Remove the knee bolster. 14. Remove the nuts and the bolts securing the steering column. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 2 15. Disconnect the steering column electrical connectors. 16. Lower the steering column. 17. Remove the screw behind the stereo cassette AM/FM radio. 18. Remove the screw securing the instrument panel to the heater air distributor case. 19. Remove the bolts and the glove box brace. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 3 20. Remove the instrument panel screw behind the glove box brace. 21. Remove the instrument panel bolts below the windshield. 22. Remove the bolts securing the bottom of the instrument panel to the floor. 23. Remove the bolts securing the sides of the instrument panel to the body. 2002 Daewoo Leganza SE L4-2.2L DOHC D-TEC MFI Page 4 24. Disconnect the instrument panel electrical connectors. 25. Remove the instrument panel. Installation Procedure 1. Position the instrument panel in the vehicle. 2. Connect the instrument panel electrical connectors. NOTE: Dissimilar metals in direct contact with each other may corrode rapidly. Make sure to use the correct fasteners to prevent premature corrosion. 3. Install the bolts securing the sides of the instrument panel to the body. Tighten Tighten the instrument panel-to-body bolts to 22 N.m (16 lb-ft) . 4. Install the bolts securing the bottom of the instrument panel to the floor. Tighten Tighten the instrument panel-to-floor bolts to 22 N.m (16 lb-ft) .

Related Content:

toyota matrix 2003 evaporator removal, take dashbord daewoo leganza, how to remove headliner from cadillac escalade ext 03, daewoo 1760xl service manual, diy brass instrument repair tools, 2002 saturn sl2 owners manual, nissan sentra 02 2 5 cam torque, p1627 daewoo, 2002 daewoo lanos code, 2 2 dtec deewoo engine timing marks

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 09-06-2012

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

Related Content:

toyota tacoma 2000 REMOVE COMPRESSOR DRIVE BELT, 2002 ford ranger 2 3L timing tool, 2002 nissan altima changing camshafts, 2002 toyota tundra manual, Centurial Timing Module

1994 Nissan Maxima SE FWD Axle Shafts Removal And Installation Manual

0

Filed Under (Nissan Manuals) by admin on 21-05-2011

download
FWD AXLE SHAFT Removal 1. Raise and support vehicle. Remove wheel. Remove wheel bearing lock nut from end of drive axle. Remove disc brake caliper and suspend out of way. DO NOT allow caliper to hang by hydraulic hose. 2. Separate tie rod end from steering knuckle. Remove axle shaft from steering knuckle hub using a soft mallet. On models with ball and cage type right axle shaft, remove support bearing retainer-to-block bolts. See Fig. 4 . 3. On all models, pry right axle shaft from transaxle using screwdriver. See Fig. 1 . On M/T models, pry left axle shaft from transaxle using screwdriver. On A/T models, insert screwdriver through right axle shaft hole in differential, and drive out left axle shaft. See Fig. 2 1. Place axle shaft in soft-jawed vise with inner joint facing up. Remove boot clamps. See Fig. 4 . Mark slide joint housing and inner race in relation to axle shaft for reassembly reference. 2. Remove and discard snap ring “A”. See Fig. 3 and Fig. 4 . Remove slide joint housing. Remove snap ring “C”. Remove cage, inner race and balls as an assembly. Remove snap ring “B”. Cover axle shaft splines with tape. Remove boot. 3. To disassemble support bearing and retainer assembly on right axle shaft, remove dust shield and snap ring “D”. See Fig. 4 . Press axle shaft out of support bearing and retainer assembly. Remove snap ring and dust shield from retainer. Using bearing driver and hammer, drive support bearing out of retainer.

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, how to replace wheel bearings on a 08 silverodo, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, snap ring assemble, Need to torque specifications 1999 GMC 1500 wheel hub bearings, 1977 ford f-350 rear wheel diagram, 2009 impala hub mounting bolt torque, removing rear wheel bearing race on 06 ford f-250, removing wheel bearing off a 2009 ford ranger rear axle

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, how to remove right front axle 95 bronco, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, Torque specs for 2008 prius axle nuts, 2002 ford expedition trailing arm torque specs, 2002 dodge dakota front differential diagram, estimate front axle seal escape, DIY LEXUS GX 470 AXLE REPLACE