2003 avalanche shift linkage

You search PDF repair manual about 2003 avalanche shift linkage, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2003 avalanche shift linkage Direct Download speed 5432 Kb/s

  2003 avalanche shift linkage Full Version speed 8172 Kb/s



2003 Honda Accord EX A/ T INTERLOCK SYSTEM REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 21-01-2012

download
A/T Interlock System Circuit Diagram SHIFT LOCK SYSTEM CIRCUIT TROUBLESHOOTING 1. Press the brake pedal. Are the brake lights ON? YES -Go to step 2. NO -Repair faulty brake light circuit. 2. Connect the HDS to the DLC. Check engine speed and throttle position in the A/T data list. Is the engine speed at idle, and TPS about 0.5 V? YES -Go to step 3. NO -Repair engine speed or throttle position input. 3. Select SHIFT LOCK SOL TEST in MISC. TEST MENU, then carry out shift lock solenoid function test. Does the shift lock solenoid work properly? YES -System circuit is OK. Check the shift lock mechanism, if necessary. NO -Go to step 4. 4. Remove the center console (See CENTER CONSOLE REMOVAL/INSTALLATION ). 5. Disconnect the shift lock solenoid connector. 6. Turn the ignition switch ON (II). 7. Measure the voltage between No. 1 terminal of the shift lock solenoid connector and body ground. Fig. 3: Measuring Voltage Between No. 1 Terminal Of Shift Lock Solenoid Connector & Body Ground Is there battery voltage? YES -Go to step 8. NO -Check for blown No. 21 fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the shift lock solenoid connector and the under-dash fuse/relay box. 8. Shift the shift lever into the P position, and press the brake pedal. Do not press the accelerator. 9. Measure the voltage between shift lock solenoid connector terminals while pressing the brake pedal Fig. 4: Measuring Voltage Between Shift Lock Solenoid Connector Terminals Is there battery voltage? YES -Check the shift lock mechanism. If the mechanism is OK, replace the shift lock solenoid (see Shift Lock Solenoid Replacement ). NO -Check for poor or loose PCM connector terminal E2 at the PCM, and check for an open in the wire between PCM connector terminal E2 and shift lock solenoid connector. If the connection and wire is OK, substitute a known-good PCM and recheck. KEY INTERLOCK SYSTEM CIRCUIT TROUBLESHOOTING

Related Content:

honda 2005 solenoid c, cavalier selenoide tcc, 2002 mdx shift interlock broken, relay trasmission control on cavalier 2003, 2005 ford escape stuck shifter button, replace shift solionide on honda crv 1999, 2003 hummer H2 transmission shift connection, transmisson speed sencer on 2000 f150 how do you change it, 1998 F-150 Electronic Pressure Control Solenoid Short Circuit, how to install transmission shift solenoid buick regal ls 2000

2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose Service Procedure

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud. 1. Replace linkage arms on all three (3) sensor assemblies following Workshop Manual (WSM), Section 204-05. 2. Discard the old linkage arms. NOTE IF THE SENSOR ASSEMBLY NEEDS TO BE REPLACED FOR ANY DAMAGE/FAILURE OTHER THAN THE ONE DESCRIBED IN THIS TSB, THE REPLACEMENT ASSEMBLY IS SUPPLIED WITH A NEW STYLE LINKAGE ARM, SO THERE IS NO NEED TO ORDER ADDITIONAL LINKAGES FOR THE SERVICE REPAIR. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage OPERATION DESCRIPTION TIME 061510A 2003-2006 0.4 Hr. Expedition/Navigator: Replace The Three Linkage Arms, Includes Time To Check Diagnostic Trouble Codes (Do Not Use With 5300A, 5300A7, 5300A8) DEALER CODING CONDITION BASIC PART NO. CODE 5A967

Related Content:

2003 ford explorer front endSUSPENSION ASSEMBLY chematics, 2006 f150 front suspension diagram, air suspension sensor ford, change front struts 2006 gs300, how to repair 03 explorer front control arm, schematic for 2003 lincoln town suspension

2003 GMC Truck C 1500 P/U 2WD Engine Knocking or Lifter Noise

0

Filed Under (GMC Manuals) by admin on 30-06-2012

download
Engine Lubrication: All Technical Service Bulletins Engine – Knocking or Lifter Noise File In Section: 06 – Engine/Propulsion System Bulletin No.: 02-06-01-038 Date: December, 2002 TECHNICAL Subject: Engine Knock or Lifter Noise (Replace 0-Ring) Models: 2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT 2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4) Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter . Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi). Cause The 0-ring seal between the oil pump screen and the oil pump may be cut, causing aeration of the oil. Correction

Related Content:

2003 mitsubishi lancer es repair manual, 2003 chevrolet suburban ac evaporator, 2003 ford motorhome chassis repair manual, evap in 2003 chevy s10 pickup, 2003 pontiac vibe repair manual, front end diagram for a gmc 03 envoy, fuse diagram for 2003 impalaq, GMC Sierra 2003 Manual, 2002 chevrolet silverado 2500hd manual, torque specs for 2003 optima tie rod end

2002 Chrysler 300M Special Floor Shift Service and Repair Manual

0

Filed Under (Chrysler Manuals) by admin on 14-02-2012

download
Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp. 11. Remove cable from routing bracket (Fig. 256) 12. Remove cable-to-transaxle nut and slide cable off of stud (Fig. 255). 13. Disconnect shifter cable from shift lever assembly at transaxle (Fig. 255). 14. Remove cable from underneath vehicle. INSTALLATION 1. Make sure transaxle shift lever is in “Park.” This is the most rearward position. Verify park sprag is fully engaged by rotating either a tire or an axle shaft . 2. Position cable in vehicle and connect cable end to the transaxle shift lever (Fig. 255). 3. Verify that the washer (Fig. 255) is still in place on the cable mounting stud. Install cable to transaxle and tighten nut to 28 Nm (250 inch lbs.). 4. Rotate fill tube to original location. Install and tighten fill tube bracket bolt. 5. Install cable “push pin” into bracket as shown in (Fig. 254)

Related Content:

how install console shift handle 1999 taurus, 2002 expedition shifter cable disconnect, ford escape shift cable repair, Dodge 3500 Brown how to install shifting cable, 2004 ford f150 transmission shift cable ends, on a 2006 pt cruiser when takeing off the battery cable do you need to reset it, saturn 2008 How to install bcm, shifter cable came off 2006 Buick Terraza, need diagram of shifter cable for 2008 chevy malibu lt, how to repalce gear shift cover on toyota sienna 2006

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 18-02-2012

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

Related Content:

2004 buick rendezvous repair manual, service manual for 2004 audi a6 2 7t quattro, 2003 gmc sierra service repair manual, stepper motor for 2004 chevy trailblazer, 2005 gmc envoy repair manual, repairing center console for 2005 f150, repair manual mitsubishi diamante, 2004 chevy malibu wiring diagrams for EVAP system, manual for 2008 pontiac g5, programming 2004 tahoe instrument cluster

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 02-01-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

iS THERE A SPRING CONNECTING THE LINKAGE TO THE TPS ON A97 LESABRE, edelbrock dubble carburetor adjustment linkage, relearn on throttle body trailblazer 2005, throttle body for a 2006 buick rendezvous, relearn procedure for throttle body 2004 chevy trailblazer, volvo penta throttle control diagram, p1512 chevy trailblazer, lincoln ls throttle linkage, where is the fuel line to throttle body on a 2006 KIA RIO, jaguar s type throttle body return spring

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

vacuum connection for kancil, 4g13 engine ignition adjustments, specialist kancil carburetor, setting caburater kancil, schematic diagram of elect fuel system include locations for a 1989 toyota camry 2 0 engine passenger car, kancil overhaul module, kancil carburetor tuning, how to change kancil carburetor, Duromax 7 hp idle adjustment, carter duel quad carb adjustment

2003 Volvo XC90 2.5T L5-2.5L Turbo Brake Pad Service and Repair Manual

0

Filed Under (Volvo Manuals) by admin on 12-06-2012

download
Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove:
2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 3 Clean and check the brake caliper and dust cover. Clean and check the brake pad mating surfaces in the brake caliper and caliper holder. Check piston dust boot. NOTE: If the dust boot is damaged dirt may have penetrated the cylinder. If this is the case the caliper must be replaced. Checking the brake disc Check brake disc friction surfaces. If the brake disc displays signs of out-of-true, check its lateral run out. Replace the brake disc if it displays signs of heavy wear, variable thickness or similar. NOTE: Minimum disc thickness/replacement limit = 18.0 mm . Minimum recommended disc thickness when installing new brake pads = 18.7 mm . Installation Installing the brake pads

Related Content:

volvo xc90 2 5t turbo, 2009 scion xb rear pad replacement, 20020 envoy how to replace brake dustshield, repairing the turbo on a 2001 volvo s40, f53 brake replacement, tools needed to change brakes on 2008 pontiac torrent, change brake pads 2008 scion, cavalier 2003 service manual, 2003 volvo v40 headlight screws manual, 2005 4runner brake rotor removal

2001-2003 RAV4 HARSH SHIFT AND/ ORM.I.L. “ON”DTC P0750, P0755, P0758, AND/ ORP1760 REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 10-02-2012

download
HARSH SHIFT AND/ORM.I.L. “ON”DTCP 0750, P0755, P0758, AND/ORP1760 –TC 002-06 Revised March3,2006 Page 2of3 PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 89661–42650 1 89661–42651 89661–42653 1 89661–42652 1 89661–42660 1 89661–42661 89661–42663 Engine Control Module (ECM) 1 89661–42662 Engine Control Module (ECM) 1 89661–42810 89661–42811 1 89661–42820 89661–42821 1 89661–42880 Same 1 89661–42890 Same 1 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Toyota Diagnostic Tester Kit* NOTE: SAll components from this kit/set are required S12 MegabyteDiagnostic Tester Program Card (P/N 01002593–005) with version 13.3aSoftware (or later) is required TOY220036 1 9 *Essential SSTs. **Referstodrawer number in SST Storage System. NOTE: Additional Diagnostic Tester Kits, Program Cards, or other SST smaybeorderedby callingSPX/OTC at 1-800-933-8335. 1. If the vehicle is currently exhibiting a harsh shift condition and/or M.I.L. “ON”with DTCP0750, P0753, P0755, P0758, and/or P1760 stored, refer to the Technical Information System (TIS), 2001–2003 model year RAV4 Repair Manual: S4WD: Diagnostics/Automatic Transaxle (U140f): Problem Symptoms Table S2WD: Diagnostics/Automatic Transaxle (U142E): Problem Symptoms Table NOTE: In some instances the vehicle must be operated at least 30 minutes before the condition can be duplicated. 2. If the vehicle exhibits the above condition, replace the ECM (PCM). Parts Information Required SSTs

Related Content:

2006 toyota rav4 repair manual download

2007 HONDA ACCORD 2 AND 4-DOOR LEATHER SHIFT KNOB (M/T) INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 15-10-2011

download
INSTALLATION 1. Squeeze the ring while you pull down on the shift boot. Remove the shift knob by turning it counterclockwise. 2. Remove the shift knob from the ring by squeezing the retaining tabs and pushing it up with long nose pliers. 3. Transfer the ring to the leather shift knob 4. Install the leather shift knob on the shift lever by turning it in the clockwise direction. 5. Pull the boot upward. USE AND CARE Use a sponge or cloth and a solution of mild liquid dishwashing soap and water to clean the shift knob. Rinse the knob completely with water, then dry it with a shop towel. Never use organic solvents such as benzene, thinner, or gasoline to clean the shift knob.

Related Content:

honda 2005 solenoid c, cavalier selenoide tcc, 2002 mdx shift interlock broken, relay trasmission control on cavalier 2003, 2005 ford escape stuck shifter button, replace shift solionide on honda crv 1999, 2003 hummer H2 transmission shift connection, transmisson speed sencer on 2000 f150 how do you change it, 1998 F-150 Electronic Pressure Control Solenoid Short Circuit, how to install transmission shift solenoid buick regal ls 2000