Skip to content

2003 buick lasabre heater hose fitting replacement

You search PDF repair manual about 2003 buick lasabre heater hose fitting replacement, if there are search results will appear below. If search results do not exist, please search by others keyword.

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

2003 Volvo XC90 2.5T L5-2.5L Turbo Brake Pad Service and Repair Manual

download
Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove:
2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 3 Clean and check the brake caliper and dust cover. Clean and check the brake pad mating surfaces in the brake caliper and caliper holder. Check piston dust boot. NOTE: If the dust boot is damaged dirt may have penetrated the cylinder. If this is the case the caliper must be replaced. Checking the brake disc Check brake disc friction surfaces. If the brake disc displays signs of out-of-true, check its lateral run out. Replace the brake disc if it displays signs of heavy wear, variable thickness or similar. NOTE: Minimum disc thickness/replacement limit = 18.0 mm . Minimum recommended disc thickness when installing new brake pads = 18.7 mm . Installation Installing the brake pads

2002 Chevrolet Impala Intake Manifold Replacement (Lower) Removal And Installation Manual

download
Intake Manifold Replacement (Lower) Notes Intake Manifold Replacement – Lower Removal Procedure 1. Disconnect the negative bakery. 2. Remove the upper intake manifold. 3. Remove the left valve rocker arm cover. 4. Remove the right valve rocker arm cover. 5. Disconnect the Engine Coolant Temperature ( ECT ) sensor electrical connector. 6. Disconnect and remove the fuel injector and the Manifold Absolute Pressure (MAP) sensor wiring harnesses. 7. Remove the fuel pipe clip bolt. 8. Remove the fuel pipe clip. 9. Remove the fuel feed pipe from the fuel injector rail. 10. Remove the fuel return pipe from the fuel injector rail. 11. Remove the fuel injector rail. 12. Remove the power steering pump from the front engine cover and reposition. 13. Remove the heater inlet pipe with heater hose from the lower intake manifold and reposition. 14. Remove the radiator inlet hose from the engine. 16. Remove the lower intake manifold bolts. 17. Remove the lower intake manifold. 18. Remove the valve rocker arms and pushrods. 19. Remove the lower intake manifold gaskets and seals. 20. Clean the lower intake manifold gasket mating surfaces. 21. Remove and clean all the RTV sealant from the lower intake manifold and the engine block (1).

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

2003-2005 Toyota Corolla HEATER PERFORMANCE IMPROVEMENT Repair Manual

download
HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 3 of 15 Install Air Conditioner Unit Assembly. Air Conditioner Unit Assembly 1. Evacuate Refrigerant HFC-134a (R-134a). Equipment: Robinair R-134a Refrigerant Recovery/Recycling Machine (Robinair P/N: 342000) 2. Disconnect Negative Terminal of Battery. 3. Drain Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot, as coolant and steam can be blown out under pressure. A. Remove the radiator cap. B. Loosen the radiator and engine drain plugs and drain the coolant. C. Close the drain plugs. Engine Drain Torque: 13 Nm (130 kgfcm, 9 ftlbf) HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 4 of 15 4. Disconnect Cooler Refrigerant Suction Hose No. 1. A. Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system. Disconnect the same way as cooler refrigerant suction hose No. 1. 6. Disconnect Heater Inlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater inlet water hose. 7. Disconnect Heater Outlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater outlet water hose. 8. Place Front Wheels Facing Straight Ahead. 9. Remove Horn Button Assembly. NOTE: If the airbag connector is disconnected with the ignition switch ON, DTCs will be recorded. Before working on SRS, please refer to the Technical Information System (TIS), 2005 model year Corolla Repair Manual: Supplemental Restraint System: Supplemental Restraint System: Precaution. A. Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case.