Skip to content

2003 dodge dakota cooling fan removal

You search PDF repair manual about 2003 dodge dakota cooling fan removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

2001 Dodge Dakota CENTRAL TIMER MODULE REMOVAL AND INSTALLATION MANUAL

download
1. Connect scan tool to Data Link Connector (DLC), under lower left side of instrument panel. Turn ignition on. Using scan tool, attempt to communicate with Air Bag Control Module (ACM) and Controller Antilock Brake (CAB) module. If scan tool is able to identify or communicate with ACM and CAB, go to next step. If scan tool is not able to identify or communicate with ACM and/or CAB, perform appropriate DTC or symptom test. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION and SYMPTOM IDENTIFICATION tables under SELF-DIAGNOSTIC SYSTEM. 2. Turn ignition off. Disconnect Gray 26-pin Central Timer Module (CTM) connector C1. CTM is located behind left side kick panel. Ensure interior lights are off. Using DVOM, measure resistance between ground and Gray 26-pin CTM connector C1 terminals No. 1 and 16 (Black/Light Green wires) and No. 2 (Black wire). See Fig. 5 . If resistance is 10 ohms or less on each ground circuit, go to next step. If resistance is more than 10 ohms on any ground circuit, check for an open between appropriate CTM connector terminal and ground. See GROUND DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 3. Disconnect Gray 12-pin CTM connector C3. Using test light connected to ground, probe Gray 12-pin CTM connector C3 terminals No. 1 (Red/Tan wire) and No. 6 (Red/Light Green wire). See Fig. 8 . If test light illuminates on both circuits, go to next step. If test light does not illuminate on both circuits, check for open in appropriate circuit between power distribution center and CTM. See POWER DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 4. Turn ignition on. Using scan tool, ensure there is PCI BUS communication with other modules (besides the ACM and CAB). If scan tool is able to identify or communicate with all modules, go to next step. If scan tool is not able to identify or communicate with all modules, refer to appropriate communications symptom for diagnosis. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION table under SELF-DIAGNOSTIC SYSTEM. 5. Connect Scope Input Cable (CH7058) to channel one connector on scan tool. Connect Cable-To-Probe Adapter (CH7062) and Black and Red test probes to scope input cable. Connect Black test probe to ground. Connect Red test probe to PCI BUS circuit at Gray 26-pin CTM connector C1 terminal No. 10 (Violet/Yellow wire). 6. Using scan tool, select PEP MODULE TOOLS, LAB SCOPE, LIVE DATA. Select 12 VOLT SQUARE WAVE. Press F2 for SCOPE. Press F2 and use DOWN arrow to set voltage scale to 20 volts. Press F2 again when complete. Turn ignition on. If reading on lab scope toggles between zero and 7.5 volts, go to next step. If reading on lab scope does not toggle between zero and 7.5 volts, repair open in PCI BUS circuit (Violet/Yellow wire). 7. Replace CTM. See CENTRAL TIMER MODULE under REMOVAL & INSTALLATION

2003 HONDA CIVIC Door Panel Removal And Installation Manual

download
2003 CIVIC – Door Panel Removal/Installation Special Tools Required *KTC trim tool set SOJATP2014 *Trim pad remover, Snap-on A 177A or equivalent, commercially available 2-door NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. If applicable, remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C). 2. Remove the inner handle (A). Take care not to scratch the door panel. 3. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model). -1 Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover. -2 Remove the screws. -3 Pull the inner handle forward and out half-way to release the hook (E). -4 Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver’s side for some models). – 1 Using a trim tool, pry the cap (C), then remove the screw (D) 4. Remove the screws (H) securing the door panel. 5. Remove the mirror mount cover. 6. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it. 7. Install the door panel in the reverse order of removal, and note these items: *Replace any damaged clips. *Make sure the connectors are plugged in properly, and the rod is connected properly. *Make sure the window and power door locks operate properly. *If applicable, install the regulator handle so it points forward and up at a 45 º angle with the glass fully closed

1989-1996 Dodge Dakota Trucks COIL Ignition Tests Manual

download
Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: • 1989-92 engines: mounted to the firewall • 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor • 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head • 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket. Fig. 2: Ignition coil mounting-all 1989-92 models Fig. 3: Ignition coil wiring and mounting hardware-1993- 96 2.5L engine 1. Inspect the ignition coil for arcing while the engine is running. If the engine will not start, this can be performed while the engine is cranked by either an assistant or a remote starter. Look at the coil in dim or low light to aid visibility of any arcing. Fig. 4: Ignition coil mounting-1993-96 3.9L and 5.2L/5.9L LDC engines 2. Arcing at the tower will carbonize the wire boot, which, if it is connected to a new ignition coil, will cause the coil to fail. In such cases, clean all the carbonization away or replace the components as necessary. Fig. 5: Ignition coil mounting-1993-96 5.9L HDC engine 3. Using a coil tester or ohmmeter according to the manufacturer’s instructions, test the primary and secondary resistance. Replace any coil that does not meet the specifications indicated in the accompanying chart. 4. Inspect the secondary coil wire for any sign of damage. Replace if any damage is found. Carbon tracking on the old wire can cause arcing and the failure of a new ignition coil. REMOVAL & INSTALLATION 1989-92 Models See Figures 6 and 7 1. Disconnect the negative battery cable. 2. Disconnect the three wires from the coil. Mark them to identify for installation. Fig. 6: Remove the coil bracket bolt at the cowl Fig. 7: Unscrew the coil mounting hardware, then remove the coil from the vehicle 3. Unplug the condenser suppressor connector from the coil, if equipped. 4. Unbolt and remove the coil. To install: 5. Bolt down the coil with old bolts. 6. Connect wires to coil making sure that the proper wires are connected where they should be. 7. Connect the condenser suppressor, if equipped. 8. Connect the battery negative cable Removal and Installation V6 AND V8 ENGINES 1. Disconnect the negative battery cable. 2. Disconnect the primary wiring from the ignition coil. 3. Disconnect the secondary spark plug wire from the coil. 4. Remove the two bolts and withdraw the coil from its mounting bracket. To install:
5. Position the coil on its bracket and install the two bolts. Tighten them to 100 inch lbs. (11 Nm). If the bracket has been tapped for coil mounting bolts, these fasteners require less torque, so tighten them to 50 inch lbs. (5 Nm). 6. Connect all wiring to the ignition coil. TESTING See Figure 1 The only test you can perform without a DRBII scan tool, or equivalent, is a basic check of the sensor only.

2004 Dodge Truck RAM 1500 Truck 2WD TIMING CHAIN AND SPROCKETS REMOVAL AND INSTALLATION MANUAL

download
TIMING CHAIN AND SPROCKETS Precaution: Timing Chain Replacement CHAIN GUIDES AND TENSIONER ARMS: Replace these parts if grooving in plastic face is more than 1 mm (0.039 inch) deep. If plastic face is severely grooved or melted, the tensioner lube jet may be clogged. The tensioner should be replaced. REMOVAL 1. Disconnect negative cable from battery. 2. Drain cooling system . 3. Remove right and left cylinder head covers. 4. Remove radiator fan shroud. 5. Rotate engine until timing mark on crankshaft damper aligns with TDC mark on timing chain cover (Fig. 132) (# 1 cylinder exhaust stroke) and the camshaft sprocket “V8″ marks are at the 12 o’clock position (Fig. 133). 6. Remove power steering pump. 7. Remove access plugs (2) from left and right cylinder heads for access to chain guide fasteners (Fig. 134). 8. Remove the oil fill housing to gain access to the right side tensioner arm fastener. 9. Remove crankshaft damper and timing chain cover. 10. Collapse and pin primary chain tensioner (Fig. 135). CAUTION: Plate behind left secondary chain tensioner could fall into oil pan . Therefore, cover pan opening. 11. Remove secondary chain tensioners. 12. Remove camshaft position sensor from right cylinder head (Fig. 136). CAUTION: Care should be taken not to damage camshaft target wheel. Do not hold target wheel while loosening or tightening camshaft sprocket. Do not place the target wheel near a magnetic source of any kind. A damaged or magnetized target wheel could cause a vehicle no start condition. CAUTION: Do not forcefully rotate the camshafts or crankshaft independently of each other. Damaging intake valve to piston contact will occur. Ensure negative battery cable is disconnected to guard against accidental starter engagement. 13. Remove left and right camshaft sprocket bolts.