Skip to content

2003 ford explorer sport instrument panel lights

You search PDF repair manual about 2003 ford explorer sport instrument panel lights, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003-2005 FORD Explorer Sport Trac Alignment – Irregular Front Tire Wear SERVICE PROCEDURE

download
ISSUE Some 2003-2005 Explorer Sport Trac vehicles equipped with the Goodyear Wrangler RT/S, P255/70R16 109S AT OWL tire, may exhibit signs of feathering heel-toe wear on the inside or outside edges of the front tires . Tire noise may also be present during regular highway drive or when braking. ACTION Inspect the tires for feathering heel-toe wear. It may be necessary to rotate or replace tires and reset toe. Refer to the following Service Procedure. SERVICE PROCEDURE Zoom Sized for Print 1. Visually inspect the front tire’s inside and outside shoulder ribs (Figure 1) 2. Measure the difference in tread depth of the leading edge compared to trailing edge, of the most-worn lug (figure 2). If the average difference in tread depth between leading and trailing edge is less than 2 mm, rotate the tires . If the average difference is more than 2 mm, replace the front tires. Also inspect the rear tires and replace if necessary. 3. Ensure that the camber and caster readings are within specification

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.

1994 Ford Mercury Cougar XR7 INTERIOR FUSE PANEL IDENTIFICATION/ INSTALLATION MANUAL

download
1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid 9 – 10 Amp Main ABS Relay, ABS Module UNDERHOOD FUSE PANEL IDENTIFICATION (1994 MODELS) The “high-current” fuse panel is located in the engine compartment on the L/H fender apron. Fig. 5: Underhood Fuse Panel Identification (1994 -95 Models) Courtesy of FORD MOTOR CO. Fuse & Relay Identification 1 – 15 Amp DRL Module, Foglights 2 – 5 Amp Memory 3 – 20 Amp Ignition Coil 4 – 20 Amp Auto Shock WARNING: Always disconnect battery ground cable before servicing “high-current fuses. It is recommended that “high-current” fuses be replaced by a qualified technician. 1994 Mercury Cougar XR7 FUSES & CIRCUIT BREAKERS 1989-95 FUSES & CIRCUIT BREAKERS Ford Motor Co. Virtual Wrench

1995-1997 FORD EXPLORER TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP

download
TRANSFER CASE BINDING OR SHUDDER DIAGNOSTICS VEHICLES WITH 4.0L ENGINE SERVICE TIP ISSUE to the Data Link Connector (DLC) underneath The diagnostic procedure for binding or shudder the steering wheel. Monitor for any Diagnostic from transfer case in slow, tight turns while in 4 Trouble Codes (DTCs) set by the transfer case Auto mode may be inaccurate for some vehicles. that could indicate incorrect speed sensor function. Codes could include, but are not ACTION limited to: Diagnose transfer case binding or shudder concerns using the following Diagnostic Procedure. •P1836 – Front propshaft sensor circuit failure •P1837 – Rear propshaft sensor circuit failure DIAGNOSTIC PROCEDURE •P1874 – Hall effect sensor power short circuit to battery 1997 EXPLORER •P1875 – Hall effect sensor power circuit 1. Test drive the vehicle in 4 Auto, 4 High and 4 failure Low. Evaluate the vehicle in each of these NOTE modes. The vehicle should bind in turns in both ADDITIONAL CODES COULD BE SET AS WELL. 4 High and 4 Low, but not in 4 Auto. The 4 PLEASE REFER TO THE APPROPRIATE YEAR High mode is intended for severe winter EXPLORER SERVICE MANUAL FOR COMPLETE weather or off-road driving only. It is not LISTING AND EXPLANATION. intended for use on dry or merely wet pavement. 3. If any of the DTCs in the above Step 2 are set, remove the corresponding speed sensor and 2. Verify the instrument panel has the proper 4X4 replace accordingly. Drive the vehicle to verify if selection label (Figure 1). Proceed to 1995-97 the shudder/binding has been eliminated. Send Explorer heading, Step 1. replaced speed sensor to the Ford Warranty 1995-97 EXPLORER Parts Return Center, Canton, MI. NOTE 4. Using NGS Tester, monitor the Parameter 4 AUTO IS THE FAR LEFT SWITCH POSITION Identification Display (PID) on the transfer case ON 1997 MODELS AND IS THE MIDDLE clutch duty cycle. If the 4 Auto mode reads POSITION ON 1996 MODELS. something higher than one (1), verify speed sensors have not set any Generic Electronic 1. If during test driving, the vehicle shudders or Module (GEM) DTCs and follow the speed binds in 4 Auto during slow forward or reverse sensor diagnostic procedure in the above Step parking lot maneuvers, proceed to Step 2. 2. Verify the following while checking PID: Mode Duty Cycle Indicator 4 Auto 0 or 1 4 High 13 4 Low 38 at 5 MPH 5. If the speed sensor circuits are functional, inspect for water contamination in the transfer case oil

1999 Ford Crown Victoria/ Grand Marquis Instrument Panel and Console Removal/ Installation Manual

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the driver side air bag module. For additional information, refer to Section 501-20B . 2. Remove the passenger side air bag module. For additional information, refer to Section 501-20B . 3. Close the glove compartment. 4. Position the speed control servo aside. 1. Disconnect the electrical connector. 2. Remove the nuts. 3. Position the speed control servo aside. 5. Disconnect the LH engine compartment in-line electrical connector. * Release the wiring harness locators. 6. Disconnect the brake fluid sensor electrical connector. 7. Disconnect the windshield wiper motor electrical connector. * Release the wiring harness locators. 8. Disconnect the LH engine compartment in-line electrical connectors. 9. Unseat the LH wiring harness grommet 10. Disconnect the blower motor electrical connector. 11. Disconnect the A/C pressure cut-off switch electrical connector. 12. Disconnect the RH engine compartment in-line wiring harness connectors. 13. Disconnect the vacuum line at the intake manifold. 14. Disconnect the electronic air temperature control (EATC) variable blower motor controller electrical connector. * Release the wiring harness locators. 15. Remove the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 16. Remove the upper front fender splash shield bolts. 17. Remove the lower front fender splash shield bolt and locator. 18. Position the front fender splash shield away from the dash panel. 19. Unlock the wiring harness guide. 20. Unseat the RH wiring harness grommet. 21. Install the RH front wheel and tire assembly. For additional information, refer to Section 204-04 . 22. Remove the RH instrument panel lower insulator. 1. Remove the pin-type retainers. 2. Release the locking tab. 3. Remove the instrument panel lower insulator. * Disconnect the courtesy lamp.