Skip to content

2003 honda accord brake interlock solenoid

You search PDF repair manual about 2003 honda accord brake interlock solenoid, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003 Honda Accord EX A/ T INTERLOCK SYSTEM REPAIR MANUAL

download
A/T Interlock System Circuit Diagram SHIFT LOCK SYSTEM CIRCUIT TROUBLESHOOTING 1. Press the brake pedal. Are the brake lights ON? YES -Go to step 2. NO -Repair faulty brake light circuit. 2. Connect the HDS to the DLC. Check engine speed and throttle position in the A/T data list. Is the engine speed at idle, and TPS about 0.5 V? YES -Go to step 3. NO -Repair engine speed or throttle position input. 3. Select SHIFT LOCK SOL TEST in MISC. TEST MENU, then carry out shift lock solenoid function test. Does the shift lock solenoid work properly? YES -System circuit is OK. Check the shift lock mechanism, if necessary. NO -Go to step 4. 4. Remove the center console (See CENTER CONSOLE REMOVAL/INSTALLATION ). 5. Disconnect the shift lock solenoid connector. 6. Turn the ignition switch ON (II). 7. Measure the voltage between No. 1 terminal of the shift lock solenoid connector and body ground. Fig. 3: Measuring Voltage Between No. 1 Terminal Of Shift Lock Solenoid Connector & Body Ground Is there battery voltage? YES -Go to step 8. NO -Check for blown No. 21 fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the shift lock solenoid connector and the under-dash fuse/relay box. 8. Shift the shift lever into the P position, and press the brake pedal. Do not press the accelerator. 9. Measure the voltage between shift lock solenoid connector terminals while pressing the brake pedal Fig. 4: Measuring Voltage Between Shift Lock Solenoid Connector Terminals Is there battery voltage? YES -Check the shift lock mechanism. If the mechanism is OK, replace the shift lock solenoid (see Shift Lock Solenoid Replacement ). NO -Check for poor or loose PCM connector terminal E2 at the PCM, and check for an open in the wire between PCM connector terminal E2 and shift lock solenoid connector. If the connection and wire is OK, substitute a known-good PCM and recheck. KEY INTERLOCK SYSTEM CIRCUIT TROUBLESHOOTING

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

HONDA Accord V6, Odyssey, Pilot Idle Vibration or Harsh Shifting Repair Manual

download
SYMPTOM There is a vibration at idle or harsh engagement when shifting the transmission between between Park, Drive, and Reverse. PROBABLE CAUSE The front hydraulic engine mount may have deteriorated and torn. PARTS INFORMATION Front Engine Mount Assembly: 1998-02 Accord V6 – P/N 50810-S87-A82, H/C 7981657 1999-04 Odyssey – P/N 50800-S0X-A04, H/C 7978927 2003-05 Pilot – P/N 50800-S3V-A82, H/C 7984560 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Failed Part: P/N 50810-S87-A81 H/C 5438593 Defect Code: 01102 Symptom Code: 04501 Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. DIAGNOSIS 1. Bring the engine up to operating temperature, and fully apply the parking brake. 2. Have an assistant view the top of the front engine mount while standing to the side of the vehicle. Shift the transmission to Drive. With your foot firmly on the brake pedal, quickly depress the accelerator pedal and release it. Your assistant should look for contact between the top of the engine mount and the bottom of the front engine mount bracket, and listen for noise from that area. REPAIR PROCEDURE 1. Drive the vehicle onto a lift, but do not raise it. 2. Odyssey – Remove the intake manifold cover and the front ignition coil cover: •See page 9-4 of the 1999-04 Odyssey Service Manual. •Online, enter keyword INTAKE , and select Intake Manifold Removal and Installation from the list. 3. Odyssey – Remove the radiator cover: •See page 10-16 of the 1999-04 Odyssey Service Manual. •Online, enter keyword RADIATOR , and select Radiator and Fan Replacement from the list

2003 Honda Accord LX REAR DISC BRAKE PADS REMOVAL AND INSTALLATION INSTRUCTIONS

download
Removal Raise and support vehicle. Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece of wire to prevent damage to brake hose. Remove 2 caliper bolts and caliper from bracket. Remove pad shims and pads. Using vernier calipers, measure the thickness of each brake pad lining. Measurement does not include pad backing plate thickness. See DISC BRAKE SPECIFICATIONS . Remove pad retainers. Inspection Clean caliper thoroughly; remove any rust, and check for grooves and cracks. Check brake disc for damage and cracks. Measure brake pad thickness. See DISC BRAKE SPECIFICATIONS . If brake pad thickness is less than service limit, replace pads as a set. Installation 1. Install pad retainers. Apply Molykote M77 compound onto pad side of shim. Wipe excess grease off shim. Keep grease off discs and pads. Install brake pads and shims. Install inner pad with its wear indicator facing downward. If you are reusing pads, install in original position. Rotate caliper piston clockwise into cylinder, then align cutout in piston with tab on inner pad by turning piston back. See Fig. 15 . 2. Lubricate boot with rubber grease to avoid twisting. If boot is twisted, back it out and position properly. Install brake caliper. Install and torque caliper bolts to proper specification. See TORQUE SPECIFICATIONS . Install brake hose onto suspension arm with mounting bolt. After installation, check for leaks. Pump brake pedal several times to seat pads. Bleed brakes as necessary. See BLEEDING BRAKE SYSTEM . WARNING: Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health. Avoid breathing dust particles. NEVER use an air hose or brush to clean brush assembly. Use an OSHA-approved vacuum cleaner. NOTE: Engagement of brake may require a greater pedal stroke immediately after brake pads have been replaced as a set. Several applications of brake pedal will restore normal pedal stroke.

1991 Honda Civic Si FUSES AND CIRCUIT BREAKERS Identification

download
IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fig. 1: Fuse Panel Identification (1988-91) Courtesy of AMERICAN HONDA MOTOR CO., INC. Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) , 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Honda 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)