Skip to content

2003 toyota celica brake caliper bolt torque

You search PDF repair manual about 2003 toyota celica brake caliper bolt torque, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

TOYOTA Celica GT-S Front Big Brake Installation Instructions

download
Step 1 Jack up car Apply parking brake and properly block rear wheels. Break loose the lug nuts on both front wheels with a 21mm socket before jacking up the car. Make sure the jack and stand are supporting the frame rail portion of the body pan, not the flat floor pan. All Photographs Show Left Side Installation Jack Position Jack Stand Supporting Frame Rail Portion of Body Pan View of the stock left front brake assembly after wheel has been removed. NEVER LEAVE ANY VEHICLE SUPPORTED WITH ONLY A JACK, ALWAYS USE JACK STANDS. Step 2 Loosen the brake line fitting nut at the flex line using an 11mm wrench. A flare fitting wrench is preferable if available Using a pair of needle nose pliers, remove the stock clip from the hard line. Set clip aside, it will be used later when the new stainless steel lines are installed. Remove flex line fitting from standoff bracket and plug the hard line with one of the rubber plugs provided with the stainless steel line kit. This should effectively prevent fluid loss for the course of the installation. Step 3 Loosen the stock caliper mounting bolts with a 14mm wrench or socket. Remove the caliper with stock brake line attached. Be aware there may be some leakage from the open end of the brake line, but it should remain faily dry unless the pads / pistons on the caliper are retracted.

2003 Honda Accord LX REAR DISC BRAKE PADS REMOVAL AND INSTALLATION INSTRUCTIONS

download
Removal Raise and support vehicle. Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece of wire to prevent damage to brake hose. Remove 2 caliper bolts and caliper from bracket. Remove pad shims and pads. Using vernier calipers, measure the thickness of each brake pad lining. Measurement does not include pad backing plate thickness. See DISC BRAKE SPECIFICATIONS . Remove pad retainers. Inspection Clean caliper thoroughly; remove any rust, and check for grooves and cracks. Check brake disc for damage and cracks. Measure brake pad thickness. See DISC BRAKE SPECIFICATIONS . If brake pad thickness is less than service limit, replace pads as a set. Installation 1. Install pad retainers. Apply Molykote M77 compound onto pad side of shim. Wipe excess grease off shim. Keep grease off discs and pads. Install brake pads and shims. Install inner pad with its wear indicator facing downward. If you are reusing pads, install in original position. Rotate caliper piston clockwise into cylinder, then align cutout in piston with tab on inner pad by turning piston back. See Fig. 15 . 2. Lubricate boot with rubber grease to avoid twisting. If boot is twisted, back it out and position properly. Install brake caliper. Install and torque caliper bolts to proper specification. See TORQUE SPECIFICATIONS . Install brake hose onto suspension arm with mounting bolt. After installation, check for leaks. Pump brake pedal several times to seat pads. Bleed brakes as necessary. See BLEEDING BRAKE SYSTEM . WARNING: Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health. Avoid breathing dust particles. NEVER use an air hose or brush to clean brush assembly. Use an OSHA-approved vacuum cleaner. NOTE: Engagement of brake may require a greater pedal stroke immediately after brake pads have been replaced as a set. Several applications of brake pedal will restore normal pedal stroke.

2003 Volvo XC90 2.5T L5-2.5L Turbo Brake Pad Service and Repair Manual

download
Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove:
2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 3 Clean and check the brake caliper and dust cover. Clean and check the brake pad mating surfaces in the brake caliper and caliper holder. Check piston dust boot. NOTE: If the dust boot is damaged dirt may have penetrated the cylinder. If this is the case the caliper must be replaced. Checking the brake disc Check brake disc friction surfaces. If the brake disc displays signs of out-of-true, check its lateral run out. Replace the brake disc if it displays signs of heavy wear, variable thickness or similar. NOTE: Minimum disc thickness/replacement limit = 18.0 mm . Minimum recommended disc thickness when installing new brake pads = 18.7 mm . Installation Installing the brake pads

2004 Toyota Camry Disc Brake System Service/ Repair Manual

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.