Skip to content

2004 6 0 high pressure oil pump repair

You search PDF repair manual about 2004 6 0 high pressure oil pump repair, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998-2003 FORD ENGINE 7.3L DIESEL DI HIGH PRESSURE OIL PUMP LEAK REPAIR MANUAL

download
ENGINE 7.3L DIESEL DI HIGH PRESSURE OIL PUMP LEAK ACTION sensor electrical connector. High pressure oil pump leaks at the outlet fittings b. Remove the exhaust back pressure sensor. and/or end plug can be serviced without removing the pump assembly. Replace the O-rings on the 3. Remove the high pressure oil pump reservoir. fittings and the end plug using Kit 2C3Z-9G804-AA. For additional information, refer to Section All three (3) O-rings should be replaced. Apply 303-04 in the appropriate Workshop Manual. liquid thread sealer (included in the kit) prior to WARNING reinstallation. Refer to the following Service Procedure for details. SMOKING OR OPEN FLAME OF ANY TYPE MUST NOT BE PRESENT WHEN WORKING SERVICE PROCEDURE NEAR FUEL VAPOR. NOTE CAUTION BEFORE PERFORMING THE REPAIR THE FUEL SYSTEM CONTAINS PRESSURIZED PROCEDURE, MAKE SURE THAT THE CAUSE FUEL AFTER THE VEHICLE IS SHUT DOWN OF THE LEAK IS CLEARLY ESTABLISHED. AND WILL MAINTAIN THIS PRESSURE FOR A LONG PERIOD OF TIME. NOTE FOR E-SERIES AND F650/750 VEHICLES, 4. Open the fuel/water separator drain valve to FOLLOW THE PROPER HIGH PRESSURE OIL release fuel pressure. Completely drain the fuel PUMP ACCESS PROCEDURE IN THIS filter/water separator assembly. DOCUMENT FOR ACCESS TO THE HIGH 5. Disconnect the fuel supply and fuel return lines PRESSURE OIL PUMP. from the fuel filter/water separator. NOTE 6. Disconnect the two (2) cylinder head fuel FOR SUPER DUTY AND EXCURSION, PROCEED supply lines from the fuel filter/water separator

FORD HIGH PRESSURE SYSTEM DIAGNOSTICS REPAIR MANUAL

download
SERVICE PROCEDURE IT IS NOT NECESSARY TO REPLACE THE HIGH PRESSURE PUMP WHEN REPLACING THE A minimum of 3.5 MPa (500 psi or 0.8 volts) ICP is QUICK CONNECT FITTINGS. required before the injectors are enabled. No or low oil in the system, leakage at the injector upper 4. If a leak is identified in the branch tube, use D-rings, high pressure pump quick connect fitting, the following procedure to replace the branch high pressure pump discharge tube, faulty injection tube if the vehicle your working on is a F-Super pressure regulator (IPR), high pressure pump, or Duty or Excursion. For E-Series, the engine branch tube could cause low ICP pressure. needs to be removed to replace the branch tube. When replacing the branch tube, also 1. Perform the revised Powertrain Controls / install the STC bracket kit. Emissions Diagnosis (PC/ED) lead diagnostics Section 4, Hard Start / No Start Diagnostic BRANCH TUBE REPLACEMENT FOR F-SUPER Procedure Tests 10e and 10f. These tests were DUTY AND EXCURSION VEHICLES ONLY revised in January 2006. 1. Remove the transmission. See the appropriate NOTE model year Workshop Manual (WSM), Section 307-01. THE LOW PRESSURE OIL SYSTEM MUST BE WORKING PROPERLY IN ORDER FOR THE HIGH NOTE PRESSURE OIL SYSTEM TO BUILD ICP LEAVE THE FLYWHEEL ON THE ENGINE, AS IT PRESSURE. THIS INCLUDES ADEQUATE WILL MAKE IT EASIER TO TURN THE ENGINE PRESSURE AND GOOD QUALITY PROPERLY OVER TO TOP DEAD CENTER (TDC) AND THE MAINTAINED OIL. TRANSMISSION FLUID DOES NOT NEED TO BE NOTE DRAINED. THIS TSB ONLY APPLIES TO REPLACEMENT OF 2. Set engine at TDC both cylinder number 1 ANY COMPONENT FOUND DEFECTIVE WHILE rocker arms should be loose. See rocker arm PERFORMING PC/ED HARD START / NO START removal procedure in the appropriate online TESTS 10e AND 10f. WSM, Section 303-01C

1995 Nissan-Datsun Maxim Water Pump Service and Repair REMOVAL AND INSTALLATION

download
1.Drain coolant from drain plugs on radiator and both sides of cylinder block. 2.Remove drain plug on cylinder block. 3.Remove right side engine mounting, mounting bracket and nuts. 4.Remove drive belts and idler pulley bracket. 5.Remove chain tensioner cover and water pump cover. 6.Pushing timing chain tensioner sleeve, apply a stopper pin so it does not return. Then remove the chain tensioner assembly. 7.Remove the 3 water pump fixing bolts. Secure a gap between water pump gear and timing chain, by turning crankshaft pulley 2O° backwards. 8.Put M8 bolts to two M8-threaded holes out of 3 water pump fixing bolt holes 9.Tighten M8 bolts by turning half turn alternately until they reach timing chain rear case. In order to prevent damages to water pump or timing chain rear case, do not tighten one bolt continuously. Always turn each bolt half turn each time. 10.Lift up water pump and remove it. When lifting up water pump, do not allow water pump gear to hit timing chain. INSPECTION 1.Check for badly rusted or corroded body assembly. 2.Check for rough operation due to excessive end play. INSTALLATION 1.Before installing, remove all traces of liquid gasket from mating surface of water pump cover and chain tensioner cover using a scraper. Also remove traces of liquid gasket from mating surface of front cover. 2.Apply a continuous bead of liquid gasket to mating surface of chain tensioner cover and water pump cover. 3.Return the crankshaft pulley to its original position by turning it 2O° forward. 4.Install timing chain tensioner, then remove the stopper pin After installing the tensioner, race the engine at about 3,000 rpm under no load to purge air from the high-pressure chamber. The engine may produce a rattling noise. This indicates that air still remains in the chamber and is not a matter of concern. 5.Install drain plug on cylinder block. 6.Reinstall any parts removed in reverse order of removal

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE MANUAL

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2 Fig. 16: Checking Continuity Between Rocker Arm Oil Pressure Switch 2P Connector Terminals Courtesy of AMERICAN HONDA MOTOR CO., INC. Is there continuity? YES- Go to step 9 . NO- Replace the rocker arm oil pressure switch (VTEC oil pressure switch) (see ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) REMOVAL/INSTALLATION ), then go to step 13 . 9. Turn the ignition switch ON (II). 10. Measure voltage between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminal No. 1 and body ground