chevrolet cavalier powertrain control module pcm

You search PDF repair manual about chevrolet cavalier powertrain control module pcm, if there are search results will appear below. If search results do not exist, please search by others keyword.



  chevrolet cavalier powertrain control module pcm Direct Download speed 5432 Kb/s

  chevrolet cavalier powertrain control module pcm Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, 2008 colbalt heater core removal, 2010 f150heater fan speed issues, where is the blower motor resistor located on a 2003 monte carlo, location of mode motor for 99 honda civic lx, 2005 silverado ac wiring diagram, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

2004 Ford Explorer/Mountaineer Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-05-2011

download
C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw Control Disabled ABS Module This DTC will be set if the stability assist system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment, or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test Q . C2769 (ABS only) Longitudinal Acceleration Sensor Circuit Failure ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2769 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Circuit Failure ABS Module Go To Pinpoint Test H . C2770 (ABS with Stability Assist) Longitudinal Acceleration Sensor Signal Fault ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Signal Fault ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2770 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2777 Sensor Cluster Bus Failure ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault Section 418-00 . U1901 CAN Network #2 Communication Bus Fault- Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault received from external node Network Fault Section 418-00

Related Content:

ABS fault on Tahoe, hino 05 air brake fail abs, what would calls a home no waste when turning steering wheel to the right on 01 Buick LeSabre, gmc hvac relearn, ford relearn after abs sensor trans harsh, FORD FUSION U1900-ABS CAN Communication BUS Fault, ford f250 diagnostic u2023 code, ford dtc codes manual, dtc cluster busses sensor, DRL Module removal kia sedona

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Service Manual

0

Filed Under (Pontiac Manuals) by admin on 27-02-2011

download
Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI 3. Disconnect the wire harness connector to the blower motor control module. 4. Install a capacitor, P/N 25073556, into the blower motor control module connector using the following steps. Refer to the illustration above to locate the positive and negative leads of the capacitor. Refer to the Splicing Copper Wire Using Splice Clips procedure in the Wiring Systems section of SI (Document ID #303646) for more information on using splice clips. 5. If the customer concern was of a blower motor that continues to run after key off, then replace the blower motor control module and install the capacitor . Refer to the blower motor control module Replacement procedure in the HVAC section of SI. This condition is the only time you need to replace the blower motor control module. 6. Reconnect the blower motor control module connector. 7. Install the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement- Right procedure in the Instrument Panel, Gages and Console section of SI. 8. Reconnect the negative cable to the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 9. Verify proper operation of the blower motor.

Related Content:

replace 2002 suburban fan motor, 2004 cavalier stepper motors, hino blower motor replace procedure, installing heaterfan motor dodge grand caravan 2011, instructions for replacing 2004 pontiac grand prix blower motor, is the resisistor built in the blower motor on a 2012 chevy sonic?, remove heat blower motor 67 grand prix, to replace an a/c motor on a 2003 civic, wireing for blower control 2004 silverado, Hino 268 2013 fuse box for heater

1986 Ford Truck F 150 2WD Pickup Emission Maintenance Warning Module-Service Manual

0

Filed Under (Ford Manuals) by admin on 23-06-2012

download
EMISSION MAINTENANCE WARNING MODULE SERVICE INFORMATION ^LAMP – “EMISSIONS/CHECK ENGINE” – EMISSION MAINTENANCE WARNING MODULE – SERVICE INFORMATION LIGHT TRUCK: 1985-89 BRONCO 1985-87 BRONCO II 1985-89 ECONOLINE, F- 150, F-250, F-350 1985-88 RANGER 1986-87 AEROSTAR ISSUE: The Emission Maintenance Warning “EMW” module operates a light that is located on the instrument panel. For 1985-87 model year vehicles, the light will display the word “EMISSIONS”. For 1988-89 model year vehicles, the light will display the words “CHECK ENGINE”. When the light is lit, it is indicating that the 60,000 mile emission maintenance should be performed. After the maintenance is performed the EMW module must be reset to zero time. Another type of module is the “IMS” module. This module is not part of the light circuit and does not require maintenance. At a predetermined time, the IMS module directs the EEC IV processor to make a strategy change. A third type of module is the “COMBO” module. This module combines the functions of the IMS and the EMW modules. ACTION: Refer to the following module application charts for the specific vehicle application and location of the different types of modules. NOTE: FOR APPLICATIONS NOT LOSTED IN THE FOLLOWING MODULE APPLICATION CHARTS, THE “CHECK ENGINE” LIGHT IS CONTROLLED BY THE EEC IV PROCESSOR. THESE VEHICLES DO NOT USE THE “EMW” MODULE

Related Content:

1985 honda elite 150 manual, 1986 190e 2 3 crank trigger diagram, GM service manual for1986 camaro pdf, 1985 ford 302 v-8 throttle body, daewoo g25p oil filter, free rair manula for 1986 iroc, how to bypass ignition switch on a 1986 corvette, isuzu dmax manual oil change, netzsch parts manuals, 93 toyota 4runner owners manual

2006 TOYOTA YARIS ELECTRONIC CRUISE CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 2 of 7 Section II – Installation Procedure A. Pre-Installation Suggestions 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting . (figure 1) 2. Remove driver side small object box, lower dash panel, and steering column cover for easy access. B. Install Electronic Modules 1. There are two electronic modules. The larger one is the Cruise Control Module and the smaller one is the Switch Interface Module . 2. Apply the larger supplied piece of double- sided adhesive tape to the Cruise Control Module, and the smaller piece of double-sided tape to the Switch Interface Module. 3. Assemble 20-pin connector from Main Wiring Harness onto mating connector of Cruise Control Module. Apply the 10 and 4 pin connectors from Pedal Interface Harness to mating connector on Switch Interface Module. Warning: Be sure to use the 4 pin connector that is on the same side of the wire harness fuse as the 10 pin connector. Failure to do so could damage vehicle’s ECM. See the picture insert in Figure 2 for further guidance. 4. Locate the linked harness between the Cruise Control and Switch Interface Modules. Connect the four pin mating connectors. 5. Place the Cruise Control Module on the back side of the main J/B. Then place the Switch Interface Module on the inside wall of the driver-side dash left of the J/B .(figure 2,3) 6. Route the Pedal Interface Harness through steering column and down to the accelerator .(figure 4 ) TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 3 of 7 7. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of the Pedal Interface Harness. Apply the other connector to the accelerator .(figure 5) C. Wiring Connections (figures 6-12) 1. Use the supplied self-stripping connectors (T- taps) from hardware pack to apply a T-tap onto the following J/B wires

Related Content:

what duse is cruise control 2007 volvo xc90

2000-2004 Honda Insight IMA System Indicator On With IMA DTC 77 REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 16-01-2012

download
PROBLEM The IMA system indicator comes on and IMA DTC 77 (P1447) (battery module deterioration) or DTC 78 (P1449) (battery module deterioration) is set. CORRECTIVE ACTION Replace the battery module. If needed, replace the motor control module (MCM), the battery condition monitor (BCM), or both INSPECTION PROCEDURE 1. Turn the ignition switch to LOCK (0). 2. Remove the cargo floor mat (see page 20-44 of the 2000-04 Insight Service Manual). (In ISIS, use the keyword FLOOR MAT , and select Interior Trim Removal/Installation – Cargo Area from the list.) 3. Remove the battery module switch cover (two bolts), then remove the locking cover from the switch. 4. Flip the battery module switch to OFF . Reinstall the locking cover. 5. Wait at least 5 minutes to let the capacitors in the system discharge. 6. Remove the right trunk shelf support (five clips and two bolts). 7. Remove the six mid-frame cover bolts. Remove the intelligent power unit (IPU) lid (17 bolts). 8. Measure the voltage at the junction board terminals. There should be 30 V or less . If you read more than 30 V , there is a problem in the circuit; do the DTC troubleshooting first. SWITCH COVER LOCKING COVER BOLTS LOCKING COVER BATTERY MODULE SWITCH IPU LID RIGHT TRUNK SHELF SUPPORT BOLTS (17) CLIPS CLIPS BOLTS ON JUNCTION BOARD TERMINALS REPAIR PROCEDURE 1. Remove the battery module from the vehicle (see page 12-113 of the service manual). (In ISIS, use the keyword BAT MOD , and select Battery Module Removal/Installation from the list.) 2. Remove the lifting tool from the battery module. 3. Remove the mounting bolts for the MCM and the BCM (eight total). Unplug the electrical connectors (five for the MCM and three for the BCM), then remove the modules. 4. Install the MCM and the BCM in the new battery module. Use the original MCM and BCM if no replacement was needed; otherwise, use the appropriate replacement parts. Torque the mounting bolts to 9.8 N·m (7.2 lb-ft) . 5. Install the lifting tool on the battery module. 6. With someone to help you, carefully lift the battery module into the vehicle, and set it down into position. Remove the lifting tool. 7. Plug in the connectors, and install the Y condenser harness. Then install the mounting bolts. Torque the bolts to 24 N·m (17 lb-ft) . 8. Install the battery module air duct. Torque the bolt to 9.8 N·m (7.2 lb-ft) . 9. Connect the high voltage cables to the junction board. Torque the bolts to 9.8 N·m (7.2 lb-ft) . 10. Install the front and rear IPU braces and the mid- frame. Torque the bolts to 9.8 N·m (7.2 lb-ft) . Model Year MCM Part Number Replacement Part Number M/T Models 2000-01 1K000-PHM-000 thru 1K000-PHM-050 1K000-PHM-060 (H/C 7071525)

Related Content:

020139007 service bulletin, battery restoration procedure, servicing a battery module honda insight

1998 Chevrolet Chevy K Pickup DTC P1626 Theft Deterrent Fuel Enable Signal Not Received Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 24-06-2012

download
An intermittent may be caused by any of the following conditions: Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems. Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This test checks if communication can be established between the scan tool and the VTD. If the scan tool cannot communicate with the VTD, refer to Diagnostic System Check – Theft Deterrent in Theft Deterrent. 3. This test checks for any opens in the serial data circuit between the VCM and the VTD. This also checks for any intermittent malfunctions associated with the serial data circuit. 4. This step is to determine if the condition that set the DTC is still present. The engine must be cranked in order to set this DTC. If the condition is present, the engine will start and then stall, indicating the VCM is disabling fuel. 7. Use a scan tool to clear and check for any DTCs in all the modules connected to the Class 2 Serial Data circuit (VCM, VTD, ATC, and BCM). the module itself. After repairing the cause of DTC P1626, clear all DTCs from the systems capable of storing this DTC and DTC U1192. 1 Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module’s data is deleted once the Clear Info function is used. Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the scan tool. 2. Turn ON the ignition leaving the engine OFF. 3. Attempt to establish communications with the VTD (Passlock) Control Module. Does the scan tool communicate with the VTD (Passlock) Control Module? — Go to Step 3 Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent 3 Check the Class 2 Serial Data circuit for the following intermittent conditions: Did you find a problem? • An open in the Class 2 Serial Data circuit between the VCM and the VTD (Passlock) Control Module. • A short to ground. • A short to voltage. • Loose or damaged terminals at the DLC, VCM or the VTD (Passlock) Control Module. — Go to Step 6 Go to Step 4 4 1. Turn OFF the ignition. 2. Connect or install any connectors or components that were disconnected or removed. 3. Clear all DTCs using a scan tool. 4. Turn OFF the ignition for 15 seconds. 5. Attempt to start the engine. Does DTC P1626 reset? — Go to Diagnostic System Check – Theft Deterrent in Theft Deterrent Go to Step 5 5 This DTC is intermittent. Are any additional DTCs stored? — Go to the applicable DTC table Go to Diagnostic Aids 6 Repair the circuit as necessary. Refer to Wiring Repairs or Connector Repairs in Wiring Systems. Is the action complete?

Related Content:

p1626 chevy venture, 87 bonco 2 parking brake control assembly diagram, what is a class 2 malfunction, VTD? chevrolet, universal theft deterrent system for 1996 bonneville, theft deterrent module location 99 olds intrigue, hummer h3 passlock starting issue, how to reset factory lock on h3, GM Theft Deterrent System Problem, gm passlock 1 bypass instructions

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 19-05-2011

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

Related Content:

1981 chevrolet p30 motorhome brake replacement instructions, Honda service manual 1995 accord, 2005 honda crv malfunction indicator lamp reset, 2003 buick lesabre lose power for instrument panel and a/c controls, 1995 accord repair manual pdf, location of main relay 89 honda accord, Free Repair Manual 1995 Accord, fuel circuit outputs on chevy s10, fuse chart for 2002 chevy silverado 2500 no brake lights, honda accord 61-10 code

1997 Dodge Grand Caravan POWERTRAIN CONTROL MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 06-02-2012

download
POWERTRAIN CONTROL MODULE (PCM) Removal & Installation 1. The PCM is located between driver’s side front fender and power distribution center, near battery. See Fig. 1 . Disconnect negative battery cable and then positive battery cable from battery. 2. Remove bolts on side of power distribution center that secure power distribution center to mounting bracket. Remove heat shield from outside of battery. Remove battery. 3. Rotate power distribution center toward the engine to disengage power distribution center from rear mounting bracket. Pull power distribution center toward rear of vehicle to disengage power distribution center from front mounting bracket. 4. Allow power distribution center to lay aside for access to PCM. Remove electrical connectors from PCM. Electrical connectors may be removed by squeezing tabs on electrical connector together and pulling electrical connector from PCM. Remove bolts and PCM. To install, reverse removal procedure. Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. Default data is used until new data from each key start is stored. As the computer restores its memory from each new key start, driveability is restored. Driveability problems may occur during the relearn stage. Depending on the vehicle and how it is equipped, the following driveability problems may exist: z Rough or unstable idle. z Hesitation or stumble. z Rich or lean running. z Poor fuel mileage. z Harsh or poor transmission shift quality. To accelerate relearn process after battery removal and installation, vehicle should be road tested in the following manner: z Vehicle at normal operating temperature (cooling fan cycles). z Accelerate at normal throttle position (20-50%). z Cruise at light to medium throttle. z Decelerate to a stop, downshifting and using brakes normally. Manufacturers identify specific relearn procedures. See RELEARN PROCEDURES. Always complete the procedure before returning the vehicle to the owner. RELEARN PROCEDURES Theft Alarm Relearn Procedure 1. Theft alarm relearn is necessary whenever battery is disconnected or dead battery is boosted. If battery is connected or boosted without conducting relearn procedure, alarm system will enter power-up mode and vehicle will not start. 2. Before reconnecting battery or connecting booster, insert door key into driver side door lock

Related Content:

IDLE RELEARN 02 CAMRY, 04 rav4 idle at 6000 rpm after battry change, 2001 malibu throttle position sensor relearn procedure, 2006 cheverolet impala will not idle, 2008 dodge grand caravan coolant fan runs continuasly, Dodge Cruise Control Repair 2012 caravan, IRRATIC IDLING 87 2 8 V6 BLAZER

1984 Mercedes Benz 190E Fuel Delivery and Air Induction Engine Testing And Adjustment Manual

0

Filed Under (Mercedes-benz Manuals) by admin on 13-04-2012

download
Note: Test and adjust lambda control with a lambda control tester. The lambda control and the idle speed emissions level must not be tested when the engine is very hot, e.g. immediately after driving sharply or after measuring engine output on the dynamometer. Testing, adjusting 1 Complete measurement sheet. 2 Switch off air conditioning or automatic climate control. Move selector lever into position “P”. 3 Read out DTC memory. Note: Not available on model year 1984-1986. 4 Connect testers: oil remote thermometer (018)124 589 07 21 00 lambda control tester (012) twin socket (031) trigger clamp (011) exhaust probe (005)126 589 11 63 00 CO measuring instrument (006) engine tester with oscilloscope (030) multimeter (003) test cable (033)102 589 04 63 00. 5 Position extraction device (014) at exhaust tail pipe. 6 Check engine coolant level, adjust to correct level. 7 Check engine oil level, pay attention to condition of oil (visual inspection). 8 Take off air cleaner. 9 Check ease of movement and condition of throttle control linkage and throttle valve. Grease all bearing points and ball sockets. 10 Check fulcrum lever, adjust. Check whether the roller (15) in the fulcrum lever (13) is resting free of tension against end stop. Adjust fulcrum lever (13) with the connecting rod (2), if necessary, so that the roller (15) is resting free of tension against end stop. 11 Idle stop. Check whether the throttle valve is resting against idle stop. Disconnect connecting rod (2) for this step. Adjust throttle control. Engines with cruise control only. Check whether the actuator is resting against idle stop of cruise control by pressing the lever of the actuator clockwise against idle stop at cruise control. When attaching the connecting rod (21), ensure that the lever of the actuator is lifted approx. 1 mm off the idle stop at the cruise control. Adjust tie rod, if necessary. Adjust throttle control. 12 Check wide open throttle stop from the accelerator pedal , adjust. 13 Voltages Test (battery and ignition coil ): No-load voltage Connect voltmeter to the battery, paying attention to the polarity, and take reading of voltage. Specification: 12.2 volts . Ignition coil Switch on ignition with engine not running. Test the voltage terminal 15 to ground at contact 5 of diagnostic connector. Specification: battery voltage Test difference in voltage between terminal 15 and terminal 1 at contacts 5 and 4 of diagnostic connector. Specification: 0 volts If the specified values are not reached, test

Related Content:

throttle control motor relay 05 mazda 3, 1986 190e 2 3 crank trigger test, ax4n endplay pdf, carborator for mazda6 2003 manual gear, how to test actuator of stabilator, how to test throttle actuator motor, mb 1993 lamda code, throttle position sensor 1986 190e 16 valve

Related Content:

where is the blower fuse on a 2001 chevy s10, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, 2008 colbalt heater core removal, 2010 f150heater fan speed issues, where is the blower motor resistor located on a 2003 monte carlo, location of mode motor for 99 honda civic lx, 2005 silverado ac wiring diagram, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram