Skip to content

2004 kia rio timing marks

You search PDF repair manual about 2004 kia rio timing marks, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Volkswagen New Beetle GL timing belt replacement manual

REMOVAL & INSTALLATION NOTE: For 2004, manufacturer does not provide a timing belt replacement interval. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Engine code AEG is stamped into machined pad on front of cylinder block above crankcase breather, near cylinder head mating surface. See Fig. 1 . For all other 2.0L engines, engine code is stamped on transmission mating flange at the rear of the engine. See Fig. 2 . For all engines, code can also be found on the vehicle data plate and on a sticker on the timing belt cover. Fig. 2: Locating Engine Identification Code (AVH, AZG, BDC & BEV) Courtesy of VOLKSWAGEN UNITED STATES, INC. TIMING BELT Removal (AEG, AVH, AZG, BEV & BDC Engine Codes) 1. Remove right hand insulation tray from engine compartment. Remove engine cover. Rotate serpentine belt tensioner clockwise to relieve belt tension. Remove serpentine belt. See Fig. 3 . Lock in place using Mandrel (T10060) or a drift. Fig. 3: Releasing Serpentine Belt Tensioner Courtesy of VOLKSWAGEN UNITED STATES, INC. 2. Remove serpentine belt tensioner assembly. See Fig. 4 . Turn crankshaft to TDC position. See Fig. 5 . Align TDC marks visible in bellhousing access hole. See Fig. 6 . Remove upper timing belt cover. Ensure camshaft sprocket timing mark aligns with mark on rear cover. See Fig. 5 . 3. Support engine from above or below with floor jack to take engine weight off of mounts. Remove coolant reservoir and set aside. On Golf and Jetta, remove power steering reservoir (hoses attached), and set aside. On New Beetle, pull off EVAP hoses at EVAP canister and throttle valve housing. 4. On all models, remove engine mount from timing belt end of engine. See Fig. 7 . Remove crankshaft pulley from crankshaft sprocket. It is NOT necessary to remove center bolt (center bolt is torque-to-yield type that must be replaced if removed). 5. Remove timing belt covers. Remove engine support from front of engine. See Fig. 4


TIMING CHAIN AND SPROCKETS Precaution: Timing Chain Replacement CHAIN GUIDES AND TENSIONER ARMS: Replace these parts if grooving in plastic face is more than 1 mm (0.039 inch) deep. If plastic face is severely grooved or melted, the tensioner lube jet may be clogged. The tensioner should be replaced. REMOVAL 1. Disconnect negative cable from battery. 2. Drain cooling system . 3. Remove right and left cylinder head covers. 4. Remove radiator fan shroud. 5. Rotate engine until timing mark on crankshaft damper aligns with TDC mark on timing chain cover (Fig. 132) (# 1 cylinder exhaust stroke) and the camshaft sprocket “V8″ marks are at the 12 o’clock position (Fig. 133). 6. Remove power steering pump. 7. Remove access plugs (2) from left and right cylinder heads for access to chain guide fasteners (Fig. 134). 8. Remove the oil fill housing to gain access to the right side tensioner arm fastener. 9. Remove crankshaft damper and timing chain cover. 10. Collapse and pin primary chain tensioner (Fig. 135). CAUTION: Plate behind left secondary chain tensioner could fall into oil pan . Therefore, cover pan opening. 11. Remove secondary chain tensioners. 12. Remove camshaft position sensor from right cylinder head (Fig. 136). CAUTION: Care should be taken not to damage camshaft target wheel. Do not hold target wheel while loosening or tightening camshaft sprocket. Do not place the target wheel near a magnetic source of any kind. A damaged or magnetized target wheel could cause a vehicle no start condition. CAUTION: Do not forcefully rotate the camshafts or crankshaft independently of each other. Damaging intake valve to piston contact will occur. Ensure negative battery cable is disconnected to guard against accidental starter engagement. 13. Remove left and right camshaft sprocket bolts.


Fig. 79: Aligning Timing Belt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry it fully back in the direction of the arrow. 4. Temporarily tighten the tensioner pulley bolt. 5. Remove the timing belt. Fig. 80: Tightening Tensioner Pulley Bolt Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. INSTALLATION SERVICE POINTS >> A << TIMING BELT INSTALLATION CAUTION: If the timing belt is to be re-used, use chalk to mark (on its flat side) an arrow indicating the clockwise direction. CAUTION: After installing the timing belt, try to rotate the camshaft sprocket in the reverse direction. Recheck to be sure that the belt is fully tensioned and that each timing mark is in the proper position. 1. With the timing belt tensioner pulley bolt loosened, use a screwdriver to pry the tensioner pulley as close to the engine mount as possible. Then temporarily tighten tensioner bolt. Fig. 81: Adjusting Timing Belt Tensioner Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. 2. Align each of the camshaft and crankshaft sprocket timing marks. 3. Install the timing belt in the following order, while making sure that the tension side of the belt is not loose. 1. Crankshaft sprocket 2. Water pump sprocket 3. Camshaft sprocket 4. Tensioner pulley >> B << TIMING BELT TENSION ADJUSTMENT 1. Initially loosen the fixing bolt of the tensioner pulley fixed to the engine mount side by 1/4-1/2 turn, and use the force of the tensioner spring to apply tension to the belt. 2. Turn the crankshaft in the proper rotation direction (clockwise) for two rotations, and recheck to be sure that the timing marks on each sprocket are aligned.


REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 . 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . 3. Unbolt timing belt tensioner pulley, and remove timing belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. NOTE: If timing belt is to be reused, mark rotational direction on belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and exhaust valves may contact each other Inspection Inspect timing belt for wear on edges of drive teeth. Inspect the belt for signs of oil contamination, cracks, separation, worn or missing teeth, or hardened Black surface. Replace belt if worn, damaged or contaminated. Inspect belt tensioner pulley for smooth rotation. Replace if defective. Check timing belt auto tensioner for leaks. Replace if necessary. Installation 1. Install timing belt idler pulley to engine support lower bracket. Install tensioner arm, shaft and washer to cylinder block. Tighten tensioner arm bolt to specification. See TORQUE SPECIFICATIONS . 2. Install crankshaft sprocket and align timing mark. See Fig. 4 . Install camshaft sprocket and adjust installation positions as shown. See Fig. 5 and Fig. 6 . Install auto tensioner to oil pump case. Ensure that

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.