Skip to content

2004 nissan altima p0345

You search PDF repair manual about 2004 nissan altima p0345, if there are search results will appear below. If search results do not exist, please search by others keyword.

NISSAN Altima, Quest, Maxima MIL ON WITH P0340 / P0345 (CMP SENSOR) AND/ OR ENGINE IS HARD TO START WHEN WARM REPAIR MANUAL

download
ACTIONS: • If you only have DTC P0340, replace only Bank 1 CMP (Camshaft Position) Sensor. • If you only have DTC P0345, replace only Bank 2 CMP (Camshaft Position) Sensor. • If you have both codes, replace both sensors. • For a “hard to start warm” incident, replace both sensors, even if you have no codes. Refer to sections EC and EM in the correct Service Manual for sensor replacement information. If replacement of the sensors does not solve your incident, go back to ASIST for further diagnostic and repair information. PARTS INFORMATION DESCRIPTION PART # QUANTITY Camshaft Position Sensor- Bank 1 23731-6J906 1 Camshaft Position Sensor- Bank 2 23731-AL616 1 CLAIMS INFORMATION Submit a Primary Failed Part (PP) line claim using the following claims coding: DESCRIPTION PFP OP-CODESYSDIAFRT RPL One Camshaft Position Sensor (Bank 1 or Bank 2) (1) DE64AA AA 32 (2) RPL Both Camshaft Position Sensors (Banks 1 and 2) (1) DE67AA AA 32 0.3 hrs. (1) Reference the Parts Information table and use the indicated sensor P/N’s as the PFP. (2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT

NISSAN ALTIMA OR SENTRA W /QR25 ENGINE NO-START AFTER COLD SOAK REPAIR MANUAL

download
SERVICE PROCEDURE Replace Starter, Add Cleaner 1. Replace the starter motor. • Use the part number from the Parts Information section of this bulletin. • Refer to section SC, “STARTING SYSTEM, Removal and Installation” in the applicable Nissan Electronic Service Manual (ESM). 2. Add one full can of Nissan In-Tank Fuel System Cleaner to the fuel. NOTE: If the fuel tank is less than ¾ full, instruct the customer to fill the tank as soon as it is convenient after the repair. Driving with the Cleaner installed and low fuel level will not harm the fuel system or engine, but will reduce the effectiveness of the cleaning process. 3. Continue to ECM Part Number Check (next page). 1. With CONSULT-II “ON”, print the Self-DIAG Results as follows: START (Nissan) >> ENGINE >> Self-DIAG Results >> PRINT SELF-DIAG RESULTS SYSTEM ENGINE DATE XX/XX/XXXX* 11:07:11 P/N 23710-XXXXX TP020389h DTC RESULTS TIME NO DTC IS DETECTED Current ECM Part Number * Example, your screen may differ. 3. Using the printout from Step 1: • Compare the vehicle’s current ECM P/N to those shown under Current ECM P/N in Chart 1, below: • This comparison will allow you to determine if the ECM needs to be reprogrammed. Chart 1, Current ECM P/N’s: VEHICLE PACKAGE NATS? CURRENT ECM P/N A/T, ASCD YES 23710-9J305, -9J003, -9J002, -9J001, -9J000, -8J001, -8J000 M/T, ASCD YES 23710-9J315, -9J013, -9J012, -9J011, -9J010, -8J061, -8J060 A/T, no ASCD YES 23710-9J300, -9J008, -9J007, -9J006, -9J005, -8J011, -8J010 02-04 Altima M/T, no ASCD YES 23710-9J310, -9J018, -9J017, -9J016, -9J015, -8J071, -8J070 YES 23710-8U542, -8U541, -8U540, -8U041, 8U040 A/T NO 23710-8U502, -8U501, -8U500, -8U001, 8U000 YES 23710-8U562, -8U561, -8U560, -8U061, -8U060 02-03 Sentra 5 M/T NO 23710-8U512, -8U511, -8U510, -8U011, -8U010 YES 23710-8U072, -8U071, -8U070 02 Sentra 6 M/T NO 23710-8U022, -8U021, -8U020 YES 23710-8U572, -8U571, -8U570 03 Sentra 6 M/T NO 23710-8U522, -8U521, -8U520 NOTE: The 2004 Sentra ECM does not need to be reprogrammed for this bulletin. A. If your vehicle’s ECM P/N matches a P/N in the chart above: • Perform ECM Reprogramming (page 4). B. If your vehicle’s ECM P/N does not match a P/N in the chart above: • ECM Reprogramming is not necessary, bulletin complete / end here

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts