2005 2008 tacoma front wheel hub

You search PDF repair manual about 2005 2008 tacoma front wheel hub, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2005 2008 tacoma front wheel hub Direct Download speed 5432 Kb/s

  2005 2008 tacoma front wheel hub Full Version speed 8172 Kb/s



2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, Need to torque specifications 1999 GMC 1500 wheel hub bearings, snap ring assemble, 2009 impala hub mounting bolt torque, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, 1977 ford f-350 rear wheel diagram, removing rear axle bearing 2002 toyota tacoma, removing rear wheel bearing race in 06 f-250 super duty lariat, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, how to change the thermostat 2008 ford escape ehow, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 checrolet colorodo emmisions purge valve, 2008 pilot alternator replacement, FREE PDF DOWNLOAD OF 2008 SILVERADO Z71 REPAIR MAMUAL, indictor light on 2008 chevy sliverdo, 2008 ford fusion transmission sensor, ac drain on a 2008 silverado

1997 Ford Aerostar/ Ranger Wheel Grease Seal and Bearing Front Replacement and Repacking

0

Filed Under (Ford Manuals) by admin on 20-11-2011

download
Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03 . 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03 . 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation

Related Content:

F550 wheel bearing torque, f53 wheel bearing seal change, wheel bearing 2000 dodge dakota, replacing rear wheel bearing on 2006 escape, Toyota Tacoma Bearing Hub Assembly 2008 inside details, 2009 BUICL ENCLAVE WHEEL BEARING TORQUE, tools needed to change hub and bearing assembly on 2002 tahoe, installing carrier bearing silverado 2002, installing Jedster retaining bearing collar on 9 ford rearend, isuzu npr wheel bearing installation

FORD Wheel Bearings REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 16-05-2011

download
Removal & Installation Installation Installation Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle”to”wheel hub retainer nut and washer. 3. Remove the parking brake shoes. 4. Press the outboard CV”joint until it is loose from the hub. 5. Remove and discard the toe link”to”wheel knuckle nut. 6. Remove the bolt and separate the toe link from the wheel knuckle. 7. Remove and discard the upper arm”to”wheel knuckle nut. 8. Remove the bolt and separate the upper arm from the wheel knuckle. 9. Remove and discard the lower arm”to”wheel knuckle nut. ? ? WARNING Do not use a hammer to separate the outboard CV”joint from the hub. Damage to the threads and internal CV”joint components can result. ? ? WARNING Do not damage the boot while separating the toe link from the wheel knuckle. ? ? WARNING Do not damage the boot while separating the ball joint from the wheel knuckle. ? ?
To To To To install: install: install: install: 10. Remove the lower arm”to”wheel knuckle bolt. 11. Remove the wheel knuckle. 12. Using a suitable press, remove and discard the wheel hub. 13. Remove and discard the wheel bearing retainer ring. 14. Using a suitable press, remove the wheel bearing

Related Content:

1999 Toyota Prius head torque specifications, 1995 f150 4x4 alignment specfications, what is the wheel torque on a 2013 ford taurus, service manuel cwb-1742 wheel alignment, mazda 3 wheel torque, lug nut torque 2000 Ford E450, How to Read Alignment Specs, how to do a rough tire allignment, 2007 mazda 3 front axle nut torque, 1999 infiniti g20 front axle lug nuts

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

0

Filed Under (Chevrolet Manuals) by admin on 27-06-2012

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

Related Content:

wheel bearing 2004 Mountaineer, 2004 CHEVY SILVERADO TCCM, 09 silverado front axle diagram, saturn ion 3 2006 wheel nut torque, torque on 2000 tahoe front brake parts, manual silverado z71 2004, repair manual for a 95 chevy silverado, torque specs for Tahoe wheel bearing bolt, tourque specs 2003 chev truck 1500 wheels, what size is wheel hub lock nut on 2008 sierra denali

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

0

Filed Under (Buick Manuals) by admin on 04-02-2012

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

Related Content:

buick terraza hub removal, 2005 buick century code p0455, hunter 9700 user manual, 2000 buick lesabre custom manual, how to change the lower control arms on a 2005 Titan pdf, hunter lift L401, integrated wheel end FOR F150, location of fuses and relays 2003 buick park avenue, Rear Tire wear Mecury Mariner, repair manual on 2001 cadi deville on motor mount

2002 Volvo XC70 Rear Wheel Hub Replacing Removal and installation manual

0

Filed Under (Volvo Manuals) by admin on 17-05-2011

download
Remove the brake caliper mounting screws. Hang the caliper up with a piece of wire the locating pin for the brake disc the brake disc the ABS-cable holder the ABS sensor. Hang up the sensor using a piece of wire. Remove the spring strut from the lower control arm Note: the spring strut is slightly compressed. Remove the anti-roll bar from the upper control arm Use a Torx wrench as a counterhold so that the rubber boot is not damaged. Remove the tie rod from the wheel spindle. Angle the tie rod upwards so that the inner mounting for the control arm is exposed the screw holding the lower mounting for the control arm to the sub-frame. Bend the control arm downwards. Remove the screws from rear wheel hub the rear wheel hub from the wheel spindle and drive shaft. Note: Clean the splines on the drive shaft before installing the new wheel hub. Lubricate the splines using oil. Installing the rear wheel hub Note: Ensure that the hub and the wheel spindle mating surfaces are clean. Install the rear wheel hub. Use new screws and torque wrench with ring wrench kit. Tighten crosswise. Tighten to 20 Nm . Then tighten to 65 Nm . Finally angle-tighten 60° . Use bevel protractor 951 2050. the control arm to the sub-frame. Do not tighten yet the tie rod on the wheel spindle. Do not tighten yet. Install the anti-roll bar link to the upper control arm. Tighten to 80 Nm . Use a Torx wrench as a counterhold so that the boot is not damaged. Press the suspension up to its normal position

2000 Ford F-Super Duty 250-550/ Excursion/ F-53 Motorhome Chassis Workshop Manua

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
Removal 1. Set the parking brake. 2. Loosen the retaining bolts. 3. Raise the vehicle to the desired working height, keeping the axle parallel with the floor; for additional information, refer to Section 100-02 . 4. Release the parking brake. 5. Remove the wheel(s); for additional information, refer to Section 204-04 . 6. Remove the brake caliper and rotor on the single rear wheel axle; for additional information, refer to Section 206-04 . 7. Remove the retaining bolts and axle shaft. 9. d the hub nut if es apart during removal. no circumstances e operations. NOTE: The hub nut will ratchet during this operation. Remove the hub nut (counterclockwise for right-hand thread; clockwise for left-hand thread). 10. Install the Step Plate. 11. Install the 2-Jaw Puller and loosen the rear hub to the point of removal. 12. hub bearing when b. Remove the rear hub assembly. 3. l a new hub seal ub assembly is removed. NOTE: The inner bearing is located behind the hub seal. Pack each bearing and replace the hub seals; for additional information, refer to Bearings, Cups and Seals in this section. 14. treme care not to scratch or gouge the seal or bearing surfaces. If after hub removal, the hub seal or seal inner sleeve remains on the spindle, remove it as shown using the Step Plate and the 2-Jaw Puller. 15. Inspect the seal surface and inner shoulder for scratches and damage. ? Remove all scratches, gouges or galling damage with #600 or finer crocus cloth. Installation 1. NOTE: Clean the spindle thoroughly after removing the rear hub. Coat the spindle with axle lubricant. 2. b bearings must be prelubed prior to installation. Fill the hub cavity with 29.6 ml (1 oz) of SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A. 3. treme care not to damage the hub g it to contact the spindle during installation. NOTE: Coat the spindle and hub seal inside diameter with SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL- M2C192-A. NOTE: Installing the rear hub in this manner causes the outer bearing to act as a pilot making the installation easier. Push the rear hub and outer bearing onto the spindle as an assembly. ? Hold the outer bearing seated and use the bearing as a pilot

Related Content:

how to change a rear wheel hub on 2009 nissan maxima, how to repair a wheel seal on a 2004 f250, how to replace wheel bearings on 2005 acura mdx diagram

2005 -2008 Toyota Tacoma Tailgate Lock PL5200 Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 28-03-2012

download
Lock Assembly 2 Washers, 2 Nuts 2 Rod Extenders Instructions Warranty Card Tools Required: Screw Driver T-30 Torx 7 mm Socket Tech Support: Call 1-800-342-5911 Installation Instructions Tailgate Lock PL5200 Toyota Tacoma 2005 -2008 4. Turn tailgate over and put segmented washer over one of the studs 5. Screw the nut onto the stud. Repeat steps 4 and 5 on the other stud and tighten both nuts. 6. Rotate plastic rod retainer using a screw driver and remove rod. 7. 1. Insert rod into Extender slot 2. Twist Extender to retain the rod. 8. 1. Insert Extender onto arm. 2. Twist rod retainer over the Extender. 9. Repeat steps 6, 7 and 8 on the second rod to finish the installation. NOTE: If the tailgate will not open when unlocked, remove the rod extenders LIMITED WARRANTY TERMS AND CONDITIONS 1. INSTALLATION: Pop & Lock TM is not responsible for installing the Pop & Lock TM or for the harm suffered by any person as a result of installing it. 2. WARRANTIES: a) Customer acknowledges that it is unreasonable to believe that any device whatever will prevent a theft in the case of every attempt and that the most that can be expected from a so-called anti-theft or security device is that it will deter many theives. b) POP & LOCK TM MAKES, AND THE CUSTOMER RECEIVES, NO WARRANTY, EXPRESSED OR IMPLIED, EXCEPT THE WARRANTIES OF TITLE TO THE POP & LOCK TM AND THEIR MERCHANTABILITY, PARTICULARLY NO WARRANTY OF FITNESS FOR A PARTICULAR USE OR PURPOSE OR AGAINST INFRINGEMENT. c) As Customer’s only remedy, Pop & Lock TM will repair or replace, at its option and without charge, any lock that is defective in material or workmanship when received by the Customer and is returned to Pop & Lock TM , FOB Pop & Lock’s offices, within one (1) year after its receipt by the Customer. Pop & Lock TM will ship all replacement, or repaired locks to the Customer, FOB Pop & Lock’s shipping point.

Related Content:

diy tailgate lock, 2008 toyota tacoma pdf manual, 2011 toyota tundra camera within tailgate without key hole, diy tacoma power tailgate lock, free toyota tacoma repair manual RM576U2, grease points 2005 -2013 tacoma lube points, How do I install a locking tailgate handle on Tacoma Truck, how to replacere glove box lock 2008 grand prix

2004 Ford Super Duty 250 550/ Excursion Vacuum Pump Kit Workshop Manual

0

Filed Under (Ford Manuals) by admin on 12-06-2011

download
Removal 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04. 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate. 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00. Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. CAUTION: Due to the fit of the splines, the hub lock will be difficult to remove. Lifting or lightly prying (with a small bar) on the axle U-joint will ease removal. When prying on the cap/hub flange, work around the flange to uniformly withdraw the hub lock. CAUTION: The service replacement kit includes two O-ring seals. One for testing the hub lock assembly and one for reassembly into the wheel hub. DO NOT REUSE O-RING SEALS. CAUTION: Always check the vacuum leak rate of the wheel end assembly when repairing or diagnosing the axle, wheel end or hub lock performance. Loosen each retainer screw one to two turns. ? Gently pry on the hub lock cap edge to release gasket adhesion. ? Remove and discard the retainer screws. ? While lifting/jiggling the axle U-joint, pull or uniformly pry the hub lock from the wheel hub.

Related Content:

1995 ford 150 4 wheel drive front hub removal, Need to torque specifications 1999 GMC 1500 wheel hub bearings, snap ring assemble, 2009 impala hub mounting bolt torque, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, 1977 ford f-350 rear wheel diagram, removing rear axle bearing 2002 toyota tacoma, removing rear wheel bearing race in 06 f-250 super duty lariat, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes