buick terraza rear control arm bushings

You search PDF repair manual about buick terraza rear control arm bushings, if there are search results will appear below. If search results do not exist, please search by others keyword.



  buick terraza rear control arm bushings Direct Download speed 5432 Kb/s

  buick terraza rear control arm bushings Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

Coil Spring Spacer Installation Instructions

0

Filed Under (More Manuals) by admin on 24-12-2011

download
1. Check to see that the spacer kit you purchased matches the year and model of your vehicle. Spacer kits two inches or taller may require a spring compressor to install. Ball joint and tie rod forks may also be useful. 2. A good portion of your front suspension will be disassembled so this would be a good time to replace any worn parts (i.e. tie rod ends, ball joints, idler arm and any bushings) Replace bushings with polyurethane replacement parts. 3. Jack up vehicle as high as possible using jack stands for support at all times. 4. With vehicle safely off the ground remove front tires. It is advisable to disassemble on side at a time so that you can use the other side as a reference for re-assembly in the event you get side tracked. 5. Remove the brake caliper from the rotor (attached with 2 bolts inside the caliper or with press-in clips depending on the vehicle). Do not remove the brake line from the caliper unless you intend to bleed the brakes at this time. Set the caliper aside or tie it up to the frame rail. Avoid pinching the brake line. 6. Remove the tie rod from the spindle using the proper tools. Do not hit the tie rod itself or the nut on the threaded portion of the tie rod or it may cause damaged and need replacing. 7. Remove the anti-sway bar from the lower control arm. This would be a good time to replace the end link bushings with polyurethane replacement bushings. 8. If your vehicle is equipped with anti-lock brakes you must now disconnect the front rotor sensor from the dust shield or spindle and set it aside. 9. Disconnect your shock absorber completely from the vehicle whether it is mounted inside the coil spring or not. 10. Support the lower control arm with jack just touching the arm. This will prevent it from dropping when the ball joint is disconnected. 11. The use of a coil spring compressor is recommended before the following steps are taken. 12. Disconnect the upper ball joint from the top of the spindle using the proper tools. Do not hit the ball joint or the threaded end of the ball joint. Once the ball joint is free the spindle should move easily. 13. Be careful when lowering the lower control arm. The coil spring is under high compression and may shoot out when released. Do not stand near the side of the truck during this step. Lower the jack so that the lower control arm swings down. If the coil spring has not fallen out on it’s own you may need to use a pry bar from the front of the vehicle to remove it. 14. Note which end of the coil spring is “bottom” for installation. Also note the depression in the lower control arm. It is important that the last winding of the coil spring fit into the indentation completely so that the vehicle will sit level. Do not switch coil springs from side to side as some vehicles have a specific “right” and “left” coil spring. 15. Check the coil spacer for proper fitment into the coil spring mount in the frame. The flat part of the spacer should face up and touch the top of the spring mount. Some vehicles have guiding tabs to center the coil spring in its top mount. These tabs may have become bent and need to be bent back to allow the spacer to properly fit in the mount. 16. Install the coil spring with the spacer on top of it. If used the coil spring compressor should still be on the spring in a compressed state. If it is not you may need to compress the spring before re-installing. Make sure the spacer is centered in the upper mount and the bottom of the spring is properly nested in the receptor groove on the lower control arm. If you are installing a two-inch or taller spacer you may need a spring compressor. Follow all safety rules when installing the coil spring as it will be under extreme compression. 17. Raise the lower control arm with a jack once the coil spring and spacer are properly lined up. Raise until the spindle is high enough to bolt on the upper ball joint. Before bolting on the upper ball joint make sure the brake caliper and brake line are where they need to be since some brake lines run inside the spindle and outside the coil spring. 18. With the upper ball joint tight and a cotter pin re-installed you may now remove the jack from under the lower control arm. 19. Assemble all of the components previously removed (sway bar with new polyurethane bushings, tie rod ends with polyurethane grease boot, brake caliper and anti-lock sensor). Don’t forget the shock with a new colored boot while it is off. 20. Repeat instructions for other side. 21. After properly installing both spacers you can install your front tires and lower vehicle back to the ground. 22. Your vehicle may sit too high at first because the suspension needs to settle. Carefully back the vehicle up and drive forward a few times using the brakes frequently. Park on level ground and check out your lift. 23. The vehicle will now require a front wheel alignment. Failure to do so may result in severe wear on your tires and may pull to one direction

Related Content:

1997 ford ranger coil spring spacer installation, 4L60E 3 4 Accumulator Assembly, how to replace rear coil spring on a buick rendezours, how to use evertough coil spring compressor, Jeep TJ coil spring perch, labor to replace control arms g6, metal clip on ow beam 2009 mazda 6, ranger coil spring replace, replace 2006 Impala control arm bushings, replacing rear springs for 2004 toyota sienna

1988-1996 TOYOTA PICK-UP LOWER CONTROL ARMS INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
1) Park your truck on flat level surface. Chock the rear wheels. Loosen front lug nuts. Raise the front with a floo jack. Support the frame with jack stands. Remove front wheels. NOTE : ALWAYS USE JACK STANDS – NEVER RELY ON JACKS ONLY!! 2) Starting on the drivers side, locate the height adjusting bolt at the rear of the torsion bar. Measure and record the length of the threads exposed between the end of the adjusting bolt and jam nuts (Fig. A). Now make a mark at the front of the torsion bar, where it goes into the bracket bolted the lower control arm. Mark bath the bar and the bracket (Fig. B). This will index the bar into the correct position when installing. Fig. A Fig. B Note : Step #2 assumes torsion bars are in the factory position. 3) Loosen the height adjusting bolts until there is no longer any load on the torsion bars. 4) Remove the 2 bolts that hold the tensioncompression rod and sway bar end link bolts. 5) Now remove the two bolts on each arm that holds the torsion bar receiver to the back of the control arm. Slide the torsion bar and receiver back from the control arm. There is a wide spline on the torsion bar corresponding to the double width tooth on the torsion bar receiver. The receiver will not slide back onto the bar if the splines are not aligned properly. 6) Loosen and remove the 3 nuts and bolts that hold each ball joint to the lower control arms. 7) Remove the pivot bolts holding the lower control arm to the frame and remove control arm from truck. 8) Unbolt and remove original bump stops from factory arms and bolt them to you new DJM control arm. 9) Drill out the small hole on the end of the torsion bar receiver to 7/16″on both sides. This is to accept the 7/16″ x 5- 1/2″ bolt supplied. 10) Compare the new DJM control arms with the factory ones. Carefull note the diameter of the factory ball joint mounting holes. You will find either three 10mm hole used on most earlier models or larger 13mm holes on late models. If you factory arms have the 10mm holes continue to step # 10. If factory holes are 13mm it will be necessary to enlarge the holes with a 1/2″ drill bit(Fig. C). Fig. C 11) Mount the DJM control arms to the truck. Make sure the steering stops are facing the front of the truck. Insert the pivot bolts and install the washers and nuts. DO NOT TIGHTEN YET . 12) Bolt on the tensioncompression rods to the lower control arms. It mat be necessary to loosen the large nuts that hole the tensioncompression rods to the frame in order to rotate the rods to the proper angle to align bolts into control arms.

Related Content:

arm cam download

2007 HONDA ODYSSEY SPLASH GUARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 14-10-2011

download
INSTALLATION NOTE: •These instructions show the left splash guards being installed. The same procedure applies to installing the right splash guards. •Clean and wax the areas to be covered with a high-quality paste wax. Installing the Front Splash Guards 1. Turn the steering wheel all the way counter clockwise to provide access to the left front fenderwell. 2. Remove the two self-tapping screws from the left front inner fender. PARTS LIST Right front splash guard Left front splash guard Right rear splash guard Left rear splash guard 6 Self-tapping screws 2 Spring nuts 2 Square head grommets 3. Using a pushpin, make a small hole through the center of the upper clip. UPPER CLIP PUSHPIN SELF-TAPPING SCREW LEFT FRONT INNER FENDER SPLASH GUARDS P/N 08P00-SHJ-101 2 of 2 All 33039-33598 (0608) LEFT REAR SPLASH GUARD SELF-TAPPING SCREW LEFT REAR FENDERWALL SELF- TAPPING SCREW (reused) REAR BUMPER LEFT REAR SPLASH GUARD There must be no clearance. REAR BUMPER LEFT FRONT INNER FENDER LEFT FRONT SPLASH GUARD LEFT FRONT INNER FENDER SELF- TAPPING SCREW LEFT FRONT SPLASH GUARD CLIP CLIP SELF- TAPPING SCREW SELF-TAPPING SCREW (reused) LOWER HOLE 5. While holding the left splash guard against the fender, tighten the self-tapping screws in the order shown. 6. Turn the steering wheel all the way clock wise and repeat steps 2 through 4 to install the right front splash guard. Installing the Rear Splash Guard 7. Using a floor jack, lift up the left rear side of the vehicle according to the service manual. 8. Remove the self-tapping screw from the rear bumper. Using a pushpin, make a hole through the center of the recess. 9. Install one square head grommet into the hole in the left rear fenderwall. Slide one spring nut over the hole you made in step 8 in the rear bumper. 10. Position the left rear splash guard on the left rear fenderwall and rear bumper, and loosely install one self-tapping screw you removed, and the two self-tapping screws supplied with the kit. LEFT REAR FENDERWALL REAR BUMPER SELF-TAPPING SCREW (Reuse.) SQUARE HEAD GROMMET SPRING NUT RECESS PUSHPIN REAR BUMPER With RECESS SELF- TAPPING SCREW 4. Install the left front splash guard using the two self-tapping screws removed in step 2, and one self-tapping screw supplied with the kit. Do not tighten the self-tapping screws yet. 11. Hold the left rear splash guard against the fenderwall and check that there is no clearance between the splash guard and rear bumper. Tighten the three self-tapping screws in the sequence shown. 12. Repeat steps 7 thru 11 to install the right rear splash guard

Related Content:

yhs-fullyhosted_003, how do you replace liftgate relay for 2005 escalade, rear hub assembly removal for 2008 toyota tundra, installation instructions for a 2007 honda accord front bumper, ruff and tuff golf cart parts rear axle bearing, rear cam seal 2000 monterro, Rear brakes 2000 Jag xj8 procedure, rear ac lines on 05 chevy trailblazer, lincoln ls rear suspension squeak, liftgate actuator replacement tahoe

1984-2002 Pontiac Camaro / Firebird ADJUSTABLE TORQUE ARM INSTALLATION MANUAL

0

Filed Under (Pontiac Manuals) by admin on 23-02-2012

download
Inspect the motor mounts and the transmission mount. Worn, weak or broken mounts will cause the torque arm to not function properly and can cause damage to your vehicle. Stock OE transmission mounts in Camaros and Firebirds are very weak and known to fail. If you have a broken or weak transmission mount, it will cause the torque arm to actually lift the tail end of the trans. up. This could cause severe wheel hop, driveline misalignment and possible damage to the transmission, drive shaft, u-joints, rear axle, torque arm, and/or floor pan of vehicle. We highly recommend using a good quality polyurethane transmission mount like Energy Suspension #33- 1108. Using the Energy Suspension transmission mount is good insurance that your transmission stay solid and the torque arm will work to its full potential. 2. Inspect the rear suspension bushings. We strongly recommend using either Edelbrock (#5274) lower trailing arms with a spherical ball on one end and polyurethane bushings on the other, Edelbrock (#5204) trailing arms with polyurethane bushings on both ends, or other high quality trailing arms that use high quality polyurethane bushings. We also recommend the use of an Edelbrock or other high quality panhard rod to replace the stock OE piece that uses sponge rubber bushings. The lower trailing arms and panhard rod secure the rear axle under the car. Upgrading to stronger high quality tubular trailing arms and panhard rod with polyurethane bushings will increase the overall strength, eliminate the sponge feel of rubber bushings and further increase the function potential of the torque arm. Worn out trailing arm or panhard rod bushings can contribute to or cause torque arm or other suspension component failures. Remember each suspension component

Related Content:

2008 CHEVY UPLANDER TRAIL ARM BUSHINGS, how to change rear bushing in 06 chevy uplander, mistubishi fuso 4d34 idle linkage, torque on pitman arm 99 crown vic

Honda Clunk or Squeak From Rear Suspension Repair Manual

0

Filed Under (Honda Manuals) by admin on 15-02-2012

download
REPAIR PROCEDURE NOTE: ISIS online service manual information is only available for vehicles 1990 and newer. 1. Remove the rear trailing arm: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword REAR SUSPENSION, then select Suspension Arms Replacement from the list. 2. Mark the trailing arm at the arrow on the bottom of the bushing 3. Place the arm on a hydraulic press, supported by the hub base, with the spindle facing up. 4. With the hub driver, press the old bushing out of the trailing arm. 5. Install the new bushing with the short end toward the outside of the vehicle. Align the arrow with the mark you made on the trailing arm. 6. Press the new bushing into the trailing arm until its edge is 10 to 12 mm above the surface of the arm. 7. Reinstall the trailing arm. 8. If necessary, repeat steps 1 thru 7 to install a new bushing in the other rear trailing arm. 9. Bleed the brake system: •Refer to the brakes section of the appropriate service manual, or •Online, enter keyword BLEED, then select Brake System Bleeding from the list. 10. Check the wheel alignment, and adjust it if needed: •Refer to the suspension section of the appropriate service manual, or •Online, enter keyword WHEEL ALIGNMENT, then select Wheel Alignment – Rear Toe Inspection/Adjustment from the list

Related Content:

how 2002 install mountaineer rear trailing arm, removing rear torque arm on 97 buick century

2002 Volvo XC70 Rear Wheel Hub Replacing Removal and installation manual

0

Filed Under (Volvo Manuals) by admin on 17-05-2011

download
Remove the brake caliper mounting screws. Hang the caliper up with a piece of wire the locating pin for the brake disc the brake disc the ABS-cable holder the ABS sensor. Hang up the sensor using a piece of wire. Remove the spring strut from the lower control arm Note: the spring strut is slightly compressed. Remove the anti-roll bar from the upper control arm Use a Torx wrench as a counterhold so that the rubber boot is not damaged. Remove the tie rod from the wheel spindle. Angle the tie rod upwards so that the inner mounting for the control arm is exposed the screw holding the lower mounting for the control arm to the sub-frame. Bend the control arm downwards. Remove the screws from rear wheel hub the rear wheel hub from the wheel spindle and drive shaft. Note: Clean the splines on the drive shaft before installing the new wheel hub. Lubricate the splines using oil. Installing the rear wheel hub Note: Ensure that the hub and the wheel spindle mating surfaces are clean. Install the rear wheel hub. Use new screws and torque wrench with ring wrench kit. Tighten crosswise. Tighten to 20 Nm . Then tighten to 65 Nm . Finally angle-tighten 60° . Use bevel protractor 951 2050. the control arm to the sub-frame. Do not tighten yet the tie rod on the wheel spindle. Do not tighten yet. Install the anti-roll bar link to the upper control arm. Tighten to 80 Nm . Use a Torx wrench as a counterhold so that the boot is not damaged. Press the suspension up to its normal position

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, youtube replace the hub on a meritor ff981 axle

Sidekick / Tracker Solid Axle Suspension 2 Door Installation Instructions

0

Filed Under (More Manuals) by admin on 29-03-2012

download
1. Lift vehicle and support by frame & remove wheels. 2. Remove rear portion of exhaust behind cat . 3. Drain transfer case, front and rear diffs. Remove front and rear driveshafts. Remove e-brake handle cover (console) & back-off tensioner. 4. Remove rear brake drums. Disconnect e-brake cables from arm & backing plates & remove rubber cable looms from control arm & frame. 5. Support rear housing. Disconnect lower control arms, upper A-arm, breather, brake hose and shocks from the chassis. 6. Support front A-arm. Remove three nuts from the top of the strut. 2 7. Disconnect sway bar from A-arms. Separate tie rod ends at the spindles. On drivers side, disconnect brake hose at the inner fender & remove clip at the frame. Remove 3 bolts from axle flange and the lower A-arm bolts. 8. On passenger side, disconnect brake hose at the frame. Remove A-arm bolts. The axle pulls straight out of the differential. 9. Remove sway bar from frame. Separate center link from pitman arm and unbolt idler arm from frame. 10. Remove front differential with its vent and rubber isolators. ** Use of the stock front and rear bumpers will cause serious tire clearance issues. We recommend Trail Tough bumpers and nerf bars. 11. Remove outer and inner rear bumpers. 12. Remove outer and inner front bumpers. Some trimming may be done to the ends of the grill. Removal of the grill may make this easier. 3 13. The second frame cross member from the front must be removed. In preparation, unclamp the fuel and brake lines from inside the right frame rail and tie them out of harms way (Towards the motor). 14. Using a sawzall, torch, plasma or cut-off disc, remove the second frame cross member (The one under the engine oil pan) completely. Be careful not to damage the frame rails. See next 2 photos below. 14. Continued 14. Continued 15. Removal of the front A-arm brackets (on the foreward most cross member) is optional. If you choose to remove them, be sure not to damage the cross member (shown NOT removed).

FORD E450 CUTAWAY OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the front and rear bolts from the leaf spring. 2. Remove existing U-bolts and U-bolt plate that attach the axle to the leaf spring . Remove the leaf spring from the axle. 3. Remove the front spring hanger bracket , rear leaf spring hanger bracket, and any overload spring brackets . See Figure 2-1. These can be removed by grinding, or air chiseling, the heads off the factory-installed rivets, and using a hammer and punch to remove remainder of the rivet. See Figure 2-2. 3. Remove the OEM shock absorbers and retain the lower mounting fastener for later use. 4. Cut the exhaust as it bends downward after the axle, at its most vertical and straight section. See Figures 2-3 & 2-4. Save the cut-off portion for use in Section 9. Remove the rear exhaust hanger from the frame. CAUTION: Be careful that the leaf spring does not spring out of its hanger, or off the frame. FIG. 2-4 FIG. 2-1 FRONT HANGER BRACKET FIG. 2-2 LEAF SPRING REAR HANGER BRACKET FIG. 2-3 CUT HERE FOR EXHAUST MODIFICATION 6 3. DRIVER SIDE ASSEMBLY 1. Review Figure 3-1 & Figure 11-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using the (4) 7/16 x 1 1/4 UNC FLANGE BOLTS and (4) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . 3. Loosely secure the suspension Arm to the axle using (2) 5/8 UNF, 4.0 X 10.50 U-bolts, (4) 5/8 WASHERS, (4) 5/8 UNF HIGH NUTS, and the Arm Mount Plate. Make sure the locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. Note : Install the axle tube spacer between the U-bolts and Axle when installing on an E350. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the Arm to the Front Hangar using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Using the enclosed bolt hole template for the Upper Air Spring Mount, align the template to the frame using the appropriate rear spring hanger holes. Mark and drill three (3) new frame holes to 0.47″ on each side of the frame. Bolt the air spring bracket assembly to the frame using (5) 7/16 x 1 1/4 UNC CAPTIVE BOLTS and (5) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . Note : Use the correct holes designated for either the E350 or E450 chassis. See Figure 3-2. 6. Bolt the air spring to the suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut. (See Table 11-1 for appropriate Torque) . FIG. 3-2 E450 HOLE PATTERN E350 HOLE PATTERN TEMPLATE OE REAR HANGER MOUNT HOLES FRAME FIG. 3-1 AIR SPRING ARM MOUNT PLATE AXLE TUBE SPACER WEAR WASHER TRAILING ARM U-BOLT FRONT HANGER BRACKET AIR SPRING MOUNT BRACKET 7 AFTER BOTH SIDES HAVE BEEN INSTALLED (Sections 4, 5, 6) FINISH THE FOLLOWING STEPS: 7. Tighten the Arm bushing bolts and the Arm U-bolts AFTER the suspension has been installed and brought to Design Height, in Section 9.5. (See Table 11-1 for appropriate Torque) . 8. Install the new shock absorbers using the same orientation as factory, with factory and enclosed hardware. 9. IMPORTANT: Route the brake cable away from the air spring and any other moving components. It may need to be tied, or slightly repositioned in order to accommodate this. 4. PASSENGER SIDE DISASSEMBLY 1. Repeat Section 2 for the passenger’s side of the truck. 5. PASSENGER SIDE ASSEMBLY 1. Repeat Section 3 for the passenger’s side of the truck. Double-check all fasteners for proper torque. Check all clearance points and all alignments. See Figure 5-1 for details.

Related Content:

2002 rondevious change rear spring, f150 1995 changing front leaf spring brackets, head bolts torque on 2001 2 5 ford ranger, how to replace 2000 chevy cavalier exhaust bracket, how to replace mazda 3 rear coil springs, is there a metal washer before e clip on pitman arm seal gearbox on a 1997 ford f150, tie rod end at pitman armnut torque 2000 f350 7 3l 4wd, Trailing Arm bracket for 2000 Buick Century

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram