Skip to content

2005 chevy aveo repair manual download

You search PDF repair manual about 2005 chevy aveo repair manual download, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003-2005 Toyota Corolla HEATER PERFORMANCE IMPROVEMENT Repair Manual

download
HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 3 of 15 Install Air Conditioner Unit Assembly. Air Conditioner Unit Assembly 1. Evacuate Refrigerant HFC-134a (R-134a). Equipment: Robinair R-134a Refrigerant Recovery/Recycling Machine (Robinair P/N: 342000) 2. Disconnect Negative Terminal of Battery. 3. Drain Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot, as coolant and steam can be blown out under pressure. A. Remove the radiator cap. B. Loosen the radiator and engine drain plugs and drain the coolant. C. Close the drain plugs. Engine Drain Torque: 13 Nm (130 kgfcm, 9 ftlbf) HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 4 of 15 4. Disconnect Cooler Refrigerant Suction Hose No. 1. A. Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system. Disconnect the same way as cooler refrigerant suction hose No. 1. 6. Disconnect Heater Inlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater inlet water hose. 7. Disconnect Heater Outlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater outlet water hose. 8. Place Front Wheels Facing Straight Ahead. 9. Remove Horn Button Assembly. NOTE: If the airbag connector is disconnected with the ignition switch ON, DTCs will be recorded. Before working on SRS, please refer to the Technical Information System (TIS), 2005 model year Corolla Repair Manual: Supplemental Restraint System: Supplemental Restraint System: Precaution. A. Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case.

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

2004-2005 FORD F-150 FRONT BRAKE ROUGHNESS/ SHUDDER WHILE BRAKING REPAIR MANUAL

download
ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.