Skip to content

2005 expedition differential fluid

You search PDF repair manual about 2005 expedition differential fluid, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

HONDA CR-V Moan or Groan From the Rear Differential REPAIR PROCEDURE

download
REPAIR PROCEDURE: 2002-04 MODELS 1. Replace the rear differential fluid: •Refer to page 15-13 of the 2002-04 CR-V Service Manual , or •Online, enter keywords REAR DIFF, and select Rear Differential Fluid Inspection and Replacement (4WD) from the list. 2. Raise the vehicle on a lift until all four wheels are completely off the ground and can rotate freely. 3. Start the engine, and let it idle until the radiator fan cycles on and off twice. 4. Burnish the rear differential clutches: Automatic transmission models – •Set the parking brake, and shift the transmission to D. Let the engine idle for 5 minutes. •With the shift lever in D, release the parking brake, keep the wheel speed at 10 mph, and let all four wheels rotate freely for 5 minutes. •Apply the brakes to stop the wheels, repeat the bulleted steps one more time, then go to step 5. Manual transmission models – •With the engine idling and the parking brake released, shift the transmission into 1st, release the clutch, and let the wheels rotate for 5 minutes. •Disengage the clutch, and apply the brakes to stop the wheels. Shift the transmission into reverse, release the clutch, and let the wheels rotate for 5 minutes. •Shift the transmission into neutral, then apply the brakes to stop the wheels. •Repeat the bulleted steps one more time, then go to step 5. 5. Shift the transmission to P (A/T) or neutral (M/T), and turn off the engine. 6. Let the rear differential cool for 10 minutes

1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4