2005 hyundai accent manual transmission repair manual

You search PDF repair manual about 2005 hyundai accent manual transmission repair manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2005 hyundai accent manual transmission repair manual Direct Download speed 5432 Kb/s

  2005 hyundai accent manual transmission repair manual Full Version speed 8172 Kb/s



4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 4r70w transmission rebuild manual download, 2004 saturn Clutch Assembly Exploded View, manual pdf transmicion automatica ram 2001

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 1971 c10 service manual pdf, 6m70 engine manual pdf, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, cft30 scan codes, 2006 ford focus ses repair manual, 1999 chevy S10 - manual, perodua workshop manual, 1999 jeep cherokee sport 4 0 radiator repair free download

2000 Chevy Truck S10/T10 Blazer Transfer Case Removal And Installation Manual

0

Filed Under (Chevy Manuals) by admin on 18-05-2011

download
Removal Procedure 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Remove the front propeller shaft. Refer to Propeller Shaft Replacement- Front. 3. Remove the rear propeller shaft. Refer to Propeller Shaft Replacement-Rear. 4. Remove the vent hose from the transfer case. 5. Disconnect the vehicle speed sensor electrical connectors. 6. Remove the electrical connectors from the transfer case motor/encoder. 9. If equipped with a manual transmission, remove the bolt securing the left side support brace to the transmission. 10. If equipped with a manual transmission, remove the bolt and stud securing the left side support brace to the transfer case 11. If equipped with a manual transmission, remove the two bolts securing the right side support brace to the transmission and transfer case. 12. For vehicles equipped with a manual transmission, remove the six nuts securing the transfer case and bracket to the transmission 13. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 14. For vehicles equipped with a automatic transmission, remove the six nuts securing the transfer case and bracket to the transmission adapter. 15. Remove the transfer case. * Start by pulling the transfer case straight back from the transmission. * After the transfer case is pulled out from the transmission turn and lower the transfer case. 16. Remove and discard the gasket. Installation Procedure 1. Install a new gasket to the transmission. Use sealer GM P/N 12346004 in order to hold the gasket in place. 2. Raise and position the transfer case to the vehicle Notice: Refer to Fastener Notice in Service Precautions. 3. For vehicles equipped with a automatic transmission, install the six nuts securing the transfer case and bracket to the transmission adapter. * Tighten the nuts to 47 Nm (35 lb ft) . 4. For vehicles equipped with a manual transmission, install the six nuts securing the transfer case and bracket to the transmission. * Tighten the nuts to 47 Nm (35 lb ft)

Related Content:

wiring for case w20 loader, case 444-75 repair manuals free, How to rebuild Kia Sorento Transfer Case, Case 1845C Manual Download, np 208 service manual, toyota tacoma ground wire transfer case, Chevy NP208 Rebuild Instructions, 2001 ford sports trac 4x4 transfer case wiring diagram, f150 transfer case problems, ford 2003 ford explorer how transfer case works

Acura MDX Torque Converter Shudder or Vibration Between 35 and 40 MPH Repair Manual

0

Filed Under (Acura Manuals) by admin on 24-11-2011

download
1. To confirm the client’s complaint, test-drive the vehicle on a smooth road, preferably with a slight incline. Set the cruise control between 35 and 40 mph, and monitor the engine rpm using the vehicle’s tachometer, or use the HDS to take a snapshot of the engine rpm. 2. If the engine speed fluctuates several hundred rpm while maintaining a constant vehicle speed, disconnect the EGR valve and retest the vehicle. •If the fluctuation is gone, refer to the EGR troubleshooting in the service manual. •If the engine rpm still fluctuates, and the transmission does not have any other symptoms (shifting problems, slipping, transmission DTCs) go to step 3. 3. Drain the transmission fluid, then strain it through a paint strainer. •If you find little or no contamination in the strainer, the ATF is OK, even if it smells burnt, is discolored, and/or the magnetic drain plug has small chips, flakes, or metal fuzz on it. Go to REPAIR PROCEDURE A . •If you find large amounts of contamination (pieces of metal or friction material) in the strainer, go to REPAIR PROCEDURE B . REPAIR PROCEDURE A 1. Remove the torque converter: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Install the torque converter: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 3. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 4. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are off. •Start the engine, and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes. REPAIR PROCEDURE B Follow the IN-WARRANTY EXCHANGE steps in service bulletin 90-009, Automatic Transmission In- Warranty Exchange Program , to order a remanufactured A/T, replace the failed A/T, and return the failed A/T core. 1. Remove the transmission: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Clean the transmission cooler. Refer to service bulletin 89-015, ATF Cooler Cleaner . 3. Install a remanufactured transmission: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 4. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 5. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off. •Start the engine and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes

Related Content:

1998 mazda MPV owners manual, 2002 ford thunderbird service manual, cd4e pdf atsg, freelander engine control module mobility module master, how much for torque converter for 2001 mdx, torque converter problems symptoms for 1999 3 2tl acura, what is a torque shudder

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, p0753 kia rio 2004, canter 4d 35 interval wiper control relay, wiring diagram for mitsubishi canter ignition, what is the tcc solenoid on a 2 2 cavalier, Powertrain Generator 6500 Parts Diagram, Kia Rio 2001 DTC P0753, bully side ste for jeep instructions, 2006 pontiac g6 gt code po753, 4t80e tcc solenoid replacement

Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit )

0

Filed Under (More Manuals) by admin on 09-05-2012

download
2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) 1. With the ignition switch in the RUN position, test for battery voltage at the circuit fuse in the transmission solenoid power supply circuit. Refer to the appropriate SI Document for the transmission solenoid power supply circuit information. 2. If battery voltage is present at the fuse, inspect the ignition voltage circuit between the fuse and the transmission for possible opens. 3. If battery voltage is not present at the fuse, test for continuity between the fuse and the ignition switch. If NO ontinuity is between the fuse and the ignition switch, repair the open in that circuit. 4. If you have continuity between the fuse and the ignition switch, the most likely cause is the ignition switch. Replace the ignition switch using the appropriate Ignition Switch Replacement procedure in SI. Refer to group number 2.188 of the parts catalog for part description and usage of the ignition switch. Warranty Information (excluding Saab U.S. Models) For vehicles repaired under warranty, use: Warranty Information (Saab U.S. Models) For vehicles repaired under warranty, use: Labor Operation Description Labor Time N6630 Wiring and/or Connector, Transmission – Repair Use published labor operation time Labor Operation Description Failed Object Fault/Reason Code Location Code Warranty Type Repair/Action Code Labor Time 3711401 Replace part, Adj., Wiring Harness, A/T Incl. diagnosis time 2005 37114 67 0 01 05 Use published labor operation time

Related Content:

2006 hummer H3 service manual, 2005 buick lacrosse cigar lighter only no power, 2006 hummer h3 ignition switch, 2006 tundra fuse diagram, how to replace a 2005 hummer ingnition switch, ignition fuse for h3, labor time for 01 covette transmission, TIME INSTALLATION OF TRANSMISSION

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

1990 Toyota Supra Factory Repair Manual

0

Filed Under (Toyota Manuals) by admin on 04-04-2012

download
REMOVAL AND INSTALLATION OF TRANSMISSION Removal of Transmission REMOVE NEGATIVE BATTERY CABLE CAUTION: Work must be started after approx. 20 se- conds or longer from the “LOCK” position and the nega- tive (-) terminal cable is disconnected from the battery. REMOVE CENTER CLUSTER FINISH PANEL REMOVE SHIFT LEVER FROM INSIDE OF VEHICLE RAISE VEHICLE AND DRAIN TRANSMISSION OIL NOTICE: Be sure the vehicle is securely supported. REMOVE PROPELLER SHAFT Remove the propeller shaft and insert SST into the extension housing. SST 09325-2001 0 (for W58 M/T) 09325-4001 0 (for R 1 54 MIT) DISCONNECT EXHAUST FRONT PlPE FROM TAIL PlPE (a) Remove the rubber hanger. (b) Disconnect the pipe at the front side of the converter. (R154 M/T) REMOVE EXHAUST FRONT PlPE (a) Disconnect the exhaust pipe bracket from the clutch housing. (b) Remove the nuts and exhaust pipe from the exhaust manifold. DISCONNECT SPEEDOMETER CABLE DISCONNECT BACK-UP LIGHT SWITCH CONNECTOR AND REAR SPEED SENSOR CONNECTOR (wl A.B.S.) MANUAL TRANSMISSION – Removal and Installation of Transmission MT-5 10. REMOVE CLUTCH RELEASE CYLINDER 11. REMOVE STARTER Remove the mounting bolts and lay the starter alongside the engine. 12. JACK UP TRANSMISSION SLIGHTLY Raise the transmission enough to remove the weight from the rear support. 13. REMOVE ENGINE REAR MOUNTING 14. REMOVE TRANSMISSION MOUNTING BOLTS AND FLYWHEEL HOUSING UNDER COVER 15.-1 (W58 M/T) REMOVE TRANSMISSION ASSEMBLY Pull out the transmission down and toward the rear. 15.-2 (R154 M/T) REMOVE TRANSMISSION ASSEMBLY WITH CLUTCH COVER AND DISC (a) Remove the two clutch housing covers. (b) Pull out the release fork through the left clutch housing hole. (c) Place the matchmarks on the clutch cover and flywheel. (d) Remove the clutch cover set bolts while turning the crankshaft pulley. HINT: Loosen each set bolt one turn at a time until spring tension is released. (e) Remove the clutch cover and disc from the flywheel, and fully move them toward the transmission. (f) Pull out the transmission with the clutch cover and disc.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 2007 kia rio service manual, schematic for front brakes on 2005 Buick Rendezvous, 4t65e service manual online, 2007 Chevy Colorado Gas Tank Seal replace, w584a lincoln, 200lolds aleroraditor system, pontiac 2007 g6 remove radiator cover

Toyota Corolla Repair Manual 2003-2005

0

Filed Under (Toyota Manuals) by admin on 13-01-2012

repair and service manual covers Toyota Corolla, all US and Canadian models, 2003-2005. (Note: this manual does NOT include information specific to XRS models).

Table of Contents

Introduction: About this manual | Introduction | Vehicle identification numbers | Maintenance techniques, tools and working facilities | Buying parts | Jacking and towing | Booster battery (jump) starting | Conversion factors | Automotive chemicals and lubricants | Safety first! | Troubleshooting

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 4r70w transmission rebuild manual download, 2004 saturn Clutch Assembly Exploded View, manual pdf transmicion automatica ram 2001