kia sorento fuel injector wire cable

You search PDF repair manual about kia sorento fuel injector wire cable, if there are search results will appear below. If search results do not exist, please search by others keyword.



  kia sorento fuel injector wire cable Direct Download speed 5432 Kb/s

  kia sorento fuel injector wire cable Full Version speed 8172 Kb/s



1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, proper connection for horn relay 1968 chevelle, pcm drag adjustment, damaged fuel pump wiring, vcm ground wire, location of vent valve solenoid on 2010 ford ranger, 2005 tundra speed pulse signal wire location, 1998 s10 6 cylindes fuel regulator diagram

2002 Chevrolet Tahoe – 4WD Fuel Line Disconnect Tool for Fuel Filter Removal/ Installation Procedure on 5.3L Flexible Fuel Engine

0

Filed Under (Chevrolet Manuals) by admin on 17-05-2011

download
2. Install the J 34730-1A . 3. Loosen the fuel fill cap in order to relieve fuel tank vapor pressure. 4. Open the valve on the J 34730-1A in order to bleed the system pressure. The fuel connections are now safe for servicing. 5. Drain any fuel remaining in the gauge into an approved container. 6. Once the system pressure is completely relieved, remove the J 34730-1A . 7. Raise and suitably support the vehicle. Important Clean the fuel filter connections and surrounding area before disconnecting the fuel lines in order to avoid possible fuel system contamination. 8. Using a flare nut wrench and a backup wrench, disconnect the fuel line fitting from the fuel filter. 9. Pull the quick-connect fitting back until the internal retainers hit the filter stop. 10. Twist one end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 11. Twist the opposite end of the J 46363 – Fuel Line Disconnect Tool and insert it between the quick-connect fitting and the filter. 12. Once the J 46363 – Fuel Line Disconnect Tool is inserted, ensure the tool is parallel to the filter and the fitting. 13. While holding the filter, push the quick-disconnect fitting towards the filter in order to disconnect the quick- connect fitting. 14. Remove the quick-connect fitting from the filter. 15. Remove the filter from the bracket. 16. Install the new fuel filter, P/N 15173334 or P/N 25164003 (A/C Delco P/N GF847), to the bracket. 17. While holding the filter, push the fitting towards the filter in order to connect the quick-connect fitting. 18. Using a flare nut wrench and a back up wrench, connect the fuel line fitting to the filter. 19. Position the fuel sensor bracket into place and install the two nuts. Tighten Tighten the two nuts to 17 N·m(13 lb ft). 20. Lower the vehicle. 21. Tighten the fuel cap. 22. Connect the negative battery cable.

Related Content:

2002 tahoe fuel line, fuel pump gas line hose diagram kia optima, fuel line diagram for 2002 ford taurus, 2011 Rav4 fuel filter location, 01 sable fuel pump wireing, fuel filter isuzu 8981499820 replacement vic & device, firing order 2005 chev uplander 3 5 L, Echo ES 210 Fuel Line, 87 chevy fuel line routing, 2011 e350 ford fuel filter

1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, bp44 repair manual pdf, toyota so5d engine fule pump control wireing diagram pdf, lucas cav injection pump diagram, how to change water pump on a dewoo, 2002 isx cummins manual pump installation, isuzu dmax fuel pump, cav injector pump governor spring, 89 dodge dakota fuel pump diagram, rager injection pump parts manual

2001 Ford F-150 Draining-Coalescer/ Pressure Relief-Natural Gas Bi-Fuel System Repair Manual

0

Filed Under (Ford Manuals) by admin on 28-05-2012

download
1. Relieve the Bi-fuel system fuel pressure. For additional information, refer to Pressure Relief—Natural Gas Bi-Fuel System. 2. Raise the vehicle on the hoist. For additional information, refer to Section 100-02. 3. NOTE: There is an O-ring attached to the drain plug. The O-ring must be replaced each time the drain plug is removed. Remove the drain plug. 4. Install the drain plug. 5. Lower the vehicle. 6. Pressurize the fuel system. WARNING: It is important that your bi-fuel vehicle be correctly maintained by Ford bi-fuel trained personnel. If a concern occurs, it is important that correctly trained personnel diagnose the cause. If a concern relates to the fuel system, correct part replacement is imperative to keep your vehicle operating at normal performance. Bi-fuel components and gasoline specific components are not interchangeable. If your vehicle is not serviced in accordance with bi-fuel service procedures, damage can occur and your warranty may be invalidated. WARNING: Fuel supply lines are always pressurized. When servicing fuel related components, do not smoke or carry lighted tobacco or an open flame of any type. Flammable mixtures may be present and can ignite, resulting in personal injury. WARNING: The natural gas fuel system is always pressurized to 655 kPa (95 psi) downstream of the fuel pressure regulator and up to 24821 kPa (3,600 psi) upstream of the fuel pressure regulator. Use care when servicing the fuel system or personal injury can occur. WARNING: The natural gas fuel supply manifold is pressurized to 655 kPa (95 psi). Fuel pressure must be relieved prior to any fuel system service. WARNING: The fuel system pressure must be relieved before any component can be removed. The fuel tanks must be evacuated prior to tank removal. Removal of components without pressure relief or tank evacuation can cause natural gas to escape into the air and cause injury or death.

Related Content:

where to measure fuel pressure cat 3126, Ford Fusion Open Gas Tank, ford 755 backhoe crank no start, how change fuel pressure regulator on 2006 toyota tocoma, chevy uplander keeps popping fuel line off of tank, gpz 500 fuel tank is it pressurized, grand marquis fuel tank pressure sensor location, how much fuel pressure for 2002 ford 5 4, how to change fuel pressure regulator on 2000 bonniville, how to drain fuel tank rav4 2 2

2000 Ford Windstar INCORRECT FUEL GAUGE INDICATION Workshop Manual

0

Filed Under (Ford Manuals) by admin on 12-05-2012

download
The fuel gauge does not change indication unless there has been at least 3 gallons of fuel added or deleted between ignition switch cycle. Use recorded REM and instrument cluster DTCs from the Continuous and On- Demand self-test. ? Are any DTCs recorded? Yes If REM DTC B1201 or IC DTC U1131 is retrieved, GO to D6 . No GO to D2. D2 CARRY OUT THE ICM FUEL GAUGE ACTIVE COMMAND IC Active Command Select the IC FUEL GAUGE CONTROL active command. Trigger FUELLEVEL active command. Toggle and monitor the fuel gauge while adjusting the FUELLEVEL active command to read 50% and 100% Did the fuel gauge needle start at empty (E), move to half at 50%, and full (F) at 100%? Yes GO to D3. No INSTALL a new instrument cluster; REFER to Instrument Cluster. CLEAR the DTC. REPEAT the instrument cluster self-test. D3 CHECK THE FUEL GAUGE READING Fuel Pump Module C412 Connect one lead of Instrument Gauge System Tester to fuel pump module C412 Pin 5, Circuit 1357 (LB/YE), harness side. Connect the other lead to fuel pump module C412 Pin 8, Circuit 1356 (LG/VT), harness side. Set the power switch on Instrument Gauge System Tester to the ON position Set Instrument Gauge System Tester to 15 ohms. Wait one minute. Set Instrument Gauge System Tester to 160 ohms. Wait one minute. Read the fuel gauge. The fuel gauge should read full or above. Set Instrument Gauge System Tester to 15 ohms. Wait one minute. Read the fuel gauge. The fuel gauge should read empty or below Does the fuel gauge operate correctly? Yes GO to D4. No GO to D6. D4 INSPECT THE FUEL TANK Visually inspect the fuel tank for any damage or deformation. ? Is the fuel tank OK? Yes GO to D5. No INSTALL a new fuel tank. REFER to Section 310-01. TEST the system for normal operation. D5 INSPECT THE FUEL LEVEL SENSOR AND PUMP ASSEMBLY Visually inspect the fuel pump assembly for damaged wiring or connectors. Visually inspect the float and float rod for damage or obstruction

Related Content:

are there any adj to the vp44, 2005 kia sorento normal teperature, isuzu rodeo self calibrate fuel gauge calibration, 04 sport trac fuel gauge problems, ford explorer gas gauge not working, fuel canister disassemble 2001 nissan sentra, fuel guage 2003 buick century, How to fix a gas gauge 2005 impala, how to repair 1996 buick regal temperature gauge, how to repair 2006 f160 cluster

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, 99 eldorado fuel pump relay test, where is the relay switch for liftgate in 2005 esclade, where is the washer relay located in a 2009 chevy impala, 1993 corvette power seat and power window shorting out breaker, sensor switch on rear beam axle of 2005 saturn relay, g5 sunroof relay

2010 TOYOTA PRIUS FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

download
Items required for installation: Push pin 10mm bolt 10mm nut TOYOTA PRIUS 2010 FOG LAMP KIT 1 of 4 01-25-2010 STEP 3.2 • Attach fog lamp to bezel. STEP 3.3 • Fog lamp and bezel assembly. STEP 3.4 • Place fog lamp and bezel assembly onto vehicle. Fasten fog lamp to vehicle with 10mm nut and supplied screw. ( Repeat step 3 for passenger side ) STEP 4.0 Removal of interior trim on driver side STEP 4.1 • Pull up on lower door trim. STEP 4.2 • Foot panel-Remove 16mm plastic nut. STEP 4.3 • Pull foot panel inward toward center console. STEP 4.4 • Remove screw. STEP 4.5 • Disconnect hood release cable from latch by pulling down on the black cable freeing it from its location. Then moving the cable to the left away from the mounting bracket. STEP 4.6 • Remove cable from latch. STEP 4.7 • Pull lower left interior panel away from dash and unplug connectors. CAUTION! You may damage wiring and connectors if you pull too hard. Driver side interior removed. 2 of 4 01-25-2010 STEP 4.8 • Remove two screws and push back on tab to free lower panel. STEP 4.9 • Unplug connector and wire harness from panel and remove panel by pulling it toward the driver seat. STEP 5.0 Fog lamp switching wiring • Run WHITE wire through V-channel and pull female bullet connector end towards fire wall. • Connect ground wire to dashboard frame. STEP 5.4 • Plug green connector into fog lamp switch. (Plug all connectors removed from Step 4 and place panel back in position) STEP 6.0 Fog lamp wiring harness • From the panel removed under the steering wheel locate hole in grommet. STEP 6.1 • Puncture hole with O-ring pick/Philips screw driver or any sharp object no larger that the black tubing. (You want a tight seal between grommet and wire). STEP 5.1 • Remove tape from lower connector on ECU and locate BROWN wire. Use the bridge connector to connect RED wire to BROWN wire. You may need to cut RED wire to proper length. STEP 5.2 • Remove. STEP 5.3 • Replace with fog lamp switch. STEP 6.2 • Insert coat hanger or welding rod through punctured hole. Push rod far enough into engine compartment so you can retrieve it. STEP 6.3 • Bend tip or rod with needle nose pliers. STEP 6.4 • Insert hook end into bullet connector making sure black tubing is close to rod. V-channel Ground 3 of 4 01-25-2010 STEP 6.5 IMPORTANT! Wrap electrical tape around connector, tubing and rod. It is important that all three be secured as one unit so not to rip connector from wiring. You want tubing to take as much of the pull force as possible. STEP 6.6 • Apply soapy water to the entire length of black tubing and from the inside of the vehicle pull rod until wire breaks through grommet. 2.5-3ft of wiring should be sufficient. STEP 6.7 • Run wiring along side the black tube indicated until it meets female end of the WHITE fog lamp wire switch. STEP 6.8 • Connect both ends together and tie strap wiring to black tube. STEP 6.9 • On the top left corner of the fuse box (to the right of the brake fluid reservoir) locate silver ECU mounting bracket. STEP 6.10 • Remove 10mm bolts and attach BLACK ground and relay as indicated. STEP 6.11 • Attach harness connector to relay. STEP 6.12 • Run wire harness between ECU and fuse box. Run RED power wire along the same path as WHITE power wire in fuse box. Connect RED power wire to 12V power source directly above WHITE cable. STEP 7.0 Connecting wire harness to fog lamps • Run wiring for driver and passenger side lamps down toward driver side fog lamp. • Connect shortest harness to driver side fog lamp. Run wire harness alongside turn signal harness. • Use the supplied tie straps to secure passenger side wire harness along the radiator support frame shown. • Connect harness to fog lamp • END of installation

Related Content:

2010 prius fuse locations, Toyota Prius 2010 service manual, removing starter from 2005 crv, REMOVE AND REPLACE 2005 HONDA CRV STARTER, prius 2010 fuel pump fuse, kia rip radiator hose, ignition wire set 8MM Kia Sportage 2010 LX, how to change thermostat c arcadia, How do I remove the starter on a Chevy Cobalt 2006, Honda malfunction reset button location

1991-1994 FORD TEMPO VEHICLE WIRING

0

Filed Under (Ford Manuals) by admin on 26-05-2012

download
WIRING INFORMATION: 1991 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 1992 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse polarity PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (5-wire reverse polarity PINK/GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil BRAKE WIRE (+) RED/LT.GREEN At Brake Pedal Switch HORN TRIGGER (-) YELLOW/LT.GREEN Steering column LEFT FRONT WINDOW UP YELLOW At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN WHITE/BLACK At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP YELLOW/WHITE Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN TAN/BLUE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP GRAY/ORANGE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN YELLOW/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP YELLOW/BLACK Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN RED/BLACK Harness In Driver’s Kick From Driver Doo

Related Content:

1999 CHEVY SILVERADO DRIVER MIRROR MOTOR installation Instructions, 2003 pontiac vibe installing a 2 wire push button, 2002 lincoln town car driver side door expanted view, 2008 chevy driver door switch wiring schmatic, 1999 cadillac deville drivers seat diagram, 04 impala driver side window regulator diagram, expedition rear window leaks, drivers side window repair 2001 Dodge Dakota, honda cr-v drivers side armrest, driver\s junctio nbox 2 accord 2012

2004 Audi A4 L4-1.8L Turbo FWD Fuel Pump Removal And Installation Manual

0

Filed Under (Audi Manuals) by admin on 18-04-2011

download
FWD Notes Removing And Installing Fuel Pump CAUTION: To remove the Fuel Pump (FP), the fuel tank may only be filled to a maximum of 3/4. Empty fuel tank if necessary. Recommended special tools and equipment 3087 wrench for tank sensor VAS5190 fuel siphoning device Empty fuel tank Observe safety precautions. Observe rules for cleanliness. CAUTION: Observe safety precautions when disconnecting the battery. Disconnect battery Ground (GND) strap with the ignition switched off. CAUTION: Secure Ground (GND) wire of VAS5190 to a blank portion of the chassis. Pull cone piece -2- from shaft piece -1- of VAS 5190. Using insulating tape, apply a mark -arrow- on hose at length a = 1465 mm from end of suction hose. Remove fuel filler cap from fuel filler tube Screw shaft piece -1- of VAS 5190 fuel siphoning device on to fuel filler tube of fuel tank . Now slide suction hose as far into fuel tank until the mark applied earlier -arrow- stands on shaft piece. NOTE: If using a siphoning device without shaft piece, proceed principally in the same manner In this case, apply a mark -arrow- on hose at length a = 1400 mm from end of suction hose using insulating tape. The suction hose is inserted correctly when the marking applied earlier stands opposite the lip of fuel filler tube. If the hose can only be inserted with difficulty, smear it thinly with engine oil. Never use lubricants containing silicon. Drain fuel tank through fuel filler tube. Carefully remove siphoning hose. Removing Sedan: Remove luggage compartment lining. Push forward the right backrest of rear seat, if necessary. Avant: Remove left 1/3 backrest. Remove left side trim in luggage compartment and dirt tray. All: Remove cover for connector flange (arrows). Release and disconnect harness connector -1-. Disengage electrical harness connector -2- and lay it aside. CAUTION: Work on the fuel system must only be performed when engine is cold. Fuel system is under pressure. Before opening system, place rags around the connection area. Then release pressure by carefully loosening connection Mark and disconnect fuel supply line -1- and fuel return line -3- (press release tab). Disconnect ventilation line -2- (press release button).

Related Content:

2010 ford f-150 ventline on fuel tank, 99 Isuzu Amigo Fuel Tank Pressure sensor, @tacomatank com, 2003 frontier fuel tank removal, 2004 chevy suburban fuel system, fuel line diagram for 2004 impala, fuel tank size xj8 1999, is the fuel filler neck discontinued for 99 ford contour

2002 Chrysler 300M Special Floor Shift Service and Repair Manual

0

Filed Under (Chrysler Manuals) by admin on 14-02-2012

download
Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp. 11. Remove cable from routing bracket (Fig. 256) 12. Remove cable-to-transaxle nut and slide cable off of stud (Fig. 255). 13. Disconnect shifter cable from shift lever assembly at transaxle (Fig. 255). 14. Remove cable from underneath vehicle. INSTALLATION 1. Make sure transaxle shift lever is in “Park.” This is the most rearward position. Verify park sprag is fully engaged by rotating either a tire or an axle shaft . 2. Position cable in vehicle and connect cable end to the transaxle shift lever (Fig. 255). 3. Verify that the washer (Fig. 255) is still in place on the cable mounting stud. Install cable to transaxle and tighten nut to 28 Nm (250 inch lbs.). 4. Rotate fill tube to original location. Install and tighten fill tube bracket bolt. 5. Install cable “push pin” into bracket as shown in (Fig. 254)

Related Content:

how install console shift handle 1999 taurus, ford escape shift cable repair, 2002 expedition shifter cable disconnect, need diagram of shifter cable for 2008 chevy malibu lt, 2004 pontiac sunfire sunroof repair, 2004 ford f150 transmission shift cable ends, on a 2006 pt cruiser when takeing off the battery cable do you need to reset it, saturn 2008 How to install bcm, shifter cable came off 2006 Buick Terraza, how to repalce gear shift cover on toyota sienna 2006

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, proper connection for horn relay 1968 chevelle, pcm drag adjustment, damaged fuel pump wiring, vcm ground wire, location of vent valve solenoid on 2010 ford ranger, 2005 tundra speed pulse signal wire location, 1998 s10 6 cylindes fuel regulator diagram