Skip to content

2005 kia sorento heater blend door actuator

You search PDF repair manual about 2005 kia sorento heater blend door actuator, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.

2003-2005 Toyota Corolla HEATER PERFORMANCE IMPROVEMENT Repair Manual

download
HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 3 of 15 Install Air Conditioner Unit Assembly. Air Conditioner Unit Assembly 1. Evacuate Refrigerant HFC-134a (R-134a). Equipment: Robinair R-134a Refrigerant Recovery/Recycling Machine (Robinair P/N: 342000) 2. Disconnect Negative Terminal of Battery. 3. Drain Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot, as coolant and steam can be blown out under pressure. A. Remove the radiator cap. B. Loosen the radiator and engine drain plugs and drain the coolant. C. Close the drain plugs. Engine Drain Torque: 13 Nm (130 kgfcm, 9 ftlbf) HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 4 of 15 4. Disconnect Cooler Refrigerant Suction Hose No. 1. A. Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system. Disconnect the same way as cooler refrigerant suction hose No. 1. 6. Disconnect Heater Inlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater inlet water hose. 7. Disconnect Heater Outlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater outlet water hose. 8. Place Front Wheels Facing Straight Ahead. 9. Remove Horn Button Assembly. NOTE: If the airbag connector is disconnected with the ignition switch ON, DTCs will be recorded. Before working on SRS, please refer to the Technical Information System (TIS), 2005 model year Corolla Repair Manual: Supplemental Restraint System: Supplemental Restraint System: Precaution. A. Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case.

2005 CIVIC 2- AND 4- DOOR FOG LIGHTS INSTALLATION INSTRUCTIONS

download
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Open the hood and disconnect the negative cable from the battery. Cutting the Front Bumper 3. Remove these parts from the front bumper (four top clips, six bottom clips, two bottom self- tapping screws, and two fender area screws). Remove the front bumper by pulling it out toward you. Place the front bumper on a blanket, to prevent damage while installing the fog lights

1993 BMW 325i (E36) Removing and Installing/ Replacing Heater and Air Conditioning Fan (M50, S50, M52)

download
With Air Conditioning Notes Removing and Installing/Replacing Heater and Air Conditioning Fan (M50, S50, M52) * Additional work on 2-door model: Remove console for the windshield wiper system. * Position windscreen wiper, left, vertically. * Pull off rubber part and pry out grill. Zoom Sized for Print Zoom Sized for Print * Remove screws from cable channel. * Remove screws on right-hand side and take off holder. * Unscrew left-hand screw. * Pull out air collector in upwards direction. Note: Air collector will be difficult to pull out. M50, M52 Unclip covers. Unscrew bolts. Remove cover of injection-valve plate. * Unclip covers and remove screws. * Remove cover * Unfasten clips and remove blower cover. * Disconnect connector. * Unfasten clips and lift out left upper section of blower. Note: The air conditioning system remains installed. Illustration shows air conditioning unit removed.