Skip to content

2005 pt cruiser manual download

You search PDF repair manual about 2005 pt cruiser manual download, if there are search results will appear below. If search results do not exist, please search by others keyword.


ISSUE b. If new level (47 fin) rotors are present, Some 2004/2005 F-150 vehicles built before perform one (1) of the following: 11/29/2004 may exhibit front brake roughness and or shudder while braking. (1) If rotors are within minimum thickness specifications, machine the rotors using ACTION the Rotunda on vehicle brake lathe and Service the rack and pinion, rotors, and caliper the Rotunda adapter kit 201-R0093. assemblies as needed, based on vehicle build date Refer to the Workshop Manual, Section and current part levels installed on the vehicle. 206-00 for the correct on-vehicle brake Refer to the following Service Procedure. lathe procedure. SERVICE PROCEDURE (2) If rotors are beyond machinable thickness, the front rotors must be 1. Vehicles built prior to 8/20/2003 require the replaced. replacement of the rack and pinion assembly if it has not been replaced. Refer to Workshop 3. Install new service fix calipers. Manual, Section 206-03 and 211-02. NOTE 2. Determine if the vehicle has the old or new REPLACE CALIPERS WITH NEW SERVICE FIX level rotors (Figure 1). CALIPER ASSEMBLIES BY REMOVING THE CALIPERS AT THE KNUCKLES. THE SERVICE REPLACEMENT CALIPERS WILL BE PRE-ASSEMBLED WITH ANCHOR, SPRINGS, AND PADS. THE CALIPERS SHOULD BE INSTALLED AS A UNIT WITHOUT DISASSEMBLY. PART NUMBER PART NAME 6L3Z-2B120-A Caliper Asy (Right Side) 6L3Z-2B121-A Caliper Asy (Left Side) 5L3Z-1102-AB Rotor (4X2, 6 Lug) 5L3Z-1102-BA Rotor (4X2, 7 Lug) 5L3Z-1125-AA Rotor (4X4, 6 Lug) 5L3Z-1125-BA Rotor (4X4, 7 Lug) 6L3Z-3504-AA Steering Gear (Super Cab/Crew 4X2) 6L3Z-3504-BA Steering Gear (Super Cab/Crew 4X4) Figure 1 – Article 05-21-19 6L3Z-3504-CA Steering Gear (Regular Cab 4X2) 6L3Z-3504-DA Steering Gear (Regular Cab 4X4) a. If old level rotors, replace the front rotors 6L3Z-3C294-AA Retainer Spindle Nut and front caliper assemblies. Refer to Workshop Manual, Section 206-00 for front rotor and caliper replacement.


This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).

2005 Ford F-150 Drive Pinion Flange and Drive Pinion Seal Repair Manual

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 . 2. Remove the brake disc. For additional information, refer to Section 206-04 . 3. Index-mark the driveshaft flange and pinion flange for correct alignment during installation. 4. Remove the 4 driveshaft flange bolts. 5. NOTE: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the driveshaft centering socket yoke from the pinion flange. Pry only in the area shown with a suitable tool to disconnect the driveshaft centering socket yoke from the pinion flange. Using a suitable tool as shown, disconnect the driveshaft centering socket yoke from the pinion flange. ? Using mechanic’s wire, position the driveshaft aside. 6. Using a Nm (lb-in) torque wrench on the pinion nut, record the torque required to maintain rotation of the pinion gear through several revolutions. 7. Using the special tool to hold the pinion flange, remove and discard the pinion nut.2005 F-150 Workshop Manual 8. Index-mark the pinion flange in relation to the drive pinion stem to make sure of correct alignment during installation. 9. Using the special tool, remove the pinion flange. 10. Force up on the metal flange of the drive pinion seal. Install gripping pliers and strike with a hammer until the drive pinion seal is removed. Installation 1. Lubricate the new drive pinion seal with grease. 2. Using the special tool, install a new drive pinion seal. 3. Lubricate the pinion flange splines with axle lubricant. 4. NOTE: Disregard the scribe marks if a new pinion flange is being installed. Align the pinion flange with the drive pinion shaft. 5. Using the special tool, install the pinion flange. 6. l a new pinion nut with the same iginal if not replacing the collapsible spacer. If a installed, install the nut in the kit, as indicated in the chart below, or damage to the component may occur. Position the new pinion nut. Pinion Nut 7. no circumstances ut to be backed off to reduce drive pinion bearing preload. If reduced drive pinion bearing preload is required, a new drive pinion collapsible spacer and pinion nut must be installed or damage to the component may occur. NOTE: Remove the special tool while taking drive pinion bearing preload readings with the Nm (lb-in) torque wrench. Using the special tool to hold the pinion flange, tighten the pinion nut. ? Rotate the drive pinion occasionally to make sure the drive pinion bearings are seating correctly. ? Install a Nm (lb-in) torque wrench on the pinion nut. ? Rotating the drive pinion through several revolutions, take frequent drive pinion bearing preload readings until the original recorded drive pinion bearing preload reading is obtained. ? If the original recorded drive pinion bearing preload is lower than specification, tighten to the appropriate specification for used drive pinion bearings. If the drive pinion bearing preload is higher than specification, tighten the pinion nut to the original reading as recorded. For additional information, refer to the Specification portion of this section. 8. Position the driveshaft and align the index mark on the pinion flange.


TOYOTA TACOMA MY 2005- SUPERCHARGER FIT KIT Procedure Page 5 of 46 pages Issue: E 11/04/08 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). • The TIS Repair Manual can be referenced for additional details. Please see your Toyota dealer for a copy of this document. 1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 7, save this coolant as it will be reused. CAUTION: To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause the hot engine coolant and steam to blow out from the radiator. (h) All parts that are removed and not reused should be saved for the customer, i.e., “discard” means to save for the customer.

2003-2005 Toyota Corolla HEATER PERFORMANCE IMPROVEMENT Repair Manual

HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 3 of 15 Install Air Conditioner Unit Assembly. Air Conditioner Unit Assembly 1. Evacuate Refrigerant HFC-134a (R-134a). Equipment: Robinair R-134a Refrigerant Recovery/Recycling Machine (Robinair P/N: 342000) 2. Disconnect Negative Terminal of Battery. 3. Drain Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot, as coolant and steam can be blown out under pressure. A. Remove the radiator cap. B. Loosen the radiator and engine drain plugs and drain the coolant. C. Close the drain plugs. Engine Drain Torque: 13 Nm (130 kgfcm, 9 ftlbf) HEATER PERFORMANCE IMPROVEMENT – AC002-05 February 14, 2005 Page 4 of 15 4. Disconnect Cooler Refrigerant Suction Hose No. 1. A. Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system. Disconnect the same way as cooler refrigerant suction hose No. 1. 6. Disconnect Heater Inlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater inlet water hose. 7. Disconnect Heater Outlet Water Hose. Using pliers, grip the claws of the clip and slide the clip and disconnect the heater outlet water hose. 8. Place Front Wheels Facing Straight Ahead. 9. Remove Horn Button Assembly. NOTE: If the airbag connector is disconnected with the ignition switch ON, DTCs will be recorded. Before working on SRS, please refer to the Technical Information System (TIS), 2005 model year Corolla Repair Manual: Supplemental Restraint System: Supplemental Restraint System: Precaution. A. Using a torx socket wrench, loosen the 2 torx screws until the groove along the screw circumference catches on the screw case.