2006 buick lacrosse fuse box diagram

You search PDF repair manual about 2006 buick lacrosse fuse box diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2006 buick lacrosse fuse box diagram Direct Download speed 5432 Kb/s

  2006 buick lacrosse fuse box diagram Full Version speed 8172 Kb/s



2005-2006 Toyota Tundra/ Sequoia 4.7L V8 MR Tech Power-flow Intake system Installation Manual

0

Filed Under (Toyota Manuals) by admin on 23-03-2012

download
The installation of this cold air intake does require mechanical skills. Removal of engine covers, air lines and removing several plastic plugs and screws that may be difficult. It is recommended that this system be installed by a professional mechanic. Be sure to disconnect the negative terminal before proceeding. Congratulations! You have just purchased the worlds first tuned intake system. MR Technology, Leading the way! Patent pending (A) and (G) (B) (D) (A) Power-Box contents: POWER-FLOW: An air intake evolution Tools required: 1- 8mm socket 1- 10mm socket 1- 12mm socket 1- Phillips screw driver 1- 8mm nut driver 1- 55mm allen wrench 1- Disc grinder or Dremel (C) (E) Figure 1 Figure 2 Carefully, remove the mass air flow sensor from the air sensor housing to be reused later in the instruc- tions. Unhook three spring clamps from the top air box cleaner. Once the hooks have been removed, continue to detach the air box top from the lower air box cleaner. See fig. 15 for better illustration. Once the nut and bolt have been removed, continue to remove the entire hose clamp. Unplug the electrical harness clip from the mass air flow sensor as shown above. Disconnect the 4mm vacuum line located to the side of the air box cleaner. Unscrew the nut and bolt the hose clamp that secures the hose over the radiator. Loosen the two flange nuts on the engine cover in order to remove the cover. Disconnec the 6mm vacuum hose that will be reused later in the instructions. Page 2 of Part# PF2019 Unscrew the two screws from the mass air flow sensor, shown above. Loosen the hose clamp on the air duct connected to the throttle body. Unplug the crank case breather hose from the air crank case port as shown above. >>> >>>> Figure 3 Figure 8 Figure 7 Figure 6 Figure 11 Figure 10 Figure 9 Figure 14 Figure 13 Figure 12 >>>> Figure 4 Figure 5 Once the flange nuts have been removed, continue to remove the cover from the engine compartment as shown above. >>> >>> >>> >>> >>> >>> The three spring clamps shown above are unhooked from the top air box cleaner (A). Remove the air filter panel once the top has been removed (B). Once the air filter panel is removed, there are three bolts that will be removed in order to detach the lower air box cleaner. Remove the entire lower air box cleaner from the engine compartment. Place the power bands over each end of the silicone elbow. press the short end of the silicone elbow over the throttle body. Once the silicone elbow has been aligned continue to semi-tighten power band over the throttle body end. The first vibra-mount is aligned to the pre-tapped hole located behind the head lamp. The first vibra-mount is now installed as shown above. Screw the second vibra-mount is aligned over the wheel well bracket. The second vibra-mount is now installed as shown above. The stock 6mm hose is removed from the fuel pressure regulator. Press the new 16″- 4mm vacuum hose over the fuel pressure regulator port. Page 3 of Part# PF2019 Figure 15 Figure 17 Figure 16 Figure 20 Figure 19 Figure 18 Figure 23 Figure 26 Figure 25 Figure 22 Figure 21 Figure 24 (B) (A) (A) (A) >>> >>> >>> >>> Both vibra-mounts are now installed, you are now ready to go on to the next step. Place one .462 and a .412 power band over the silicone step hose. Press the 3 3/4″ side over the velocity stack as shown above. The Power box is now sitting flush over the vibra- mounts and a fender washer is placed over each vibra-mount. The last m6 flange nut is placed over the vibra- mount located behind the Power box. The 65mm bolt is tightened with an allen wrench. The assembled power box is lowered into the engine compartment. Align the mounting points on the bracket arms over the vibra-mounts. One 45mm bolt is removed from the top of the box. The bracket is place under the Power box and the 45mm bolt is aligned and screwed back in place as shown above. Remove the 65mm bolt from the velocity stack base. Align the bracket to the hole and insert the 65mm bolt back in place

Related Content:

09 cts air condition drain location, 1990 isuzu npr no power to fuse panel, mercedes benz e280 w211 2005 fuse diagrams, hitatchi ex 200 fuse box order, install 2000 celica air box, land rover freelander 2 2007 fuse box, Popping noise from air filter, replace tacoma ac drain hose, troubleshooting a mazda 6 air conditioner drain line, turn signal fuses on 2002 winnebago adventurer

Malfunction Indicator Lamp (MIL) On, Transmission Stuck in Second or Third Gear, Instrument Cluster Inoperative (Verify and Repair Source of Voltage Loss In Transmission Solenoid Power Supply Circuit )

0

Filed Under (More Manuals) by admin on 09-05-2012

download
2006 and Prior GM Passenger Cars and Light Duty Trucks 2005-2006 HUMMER H2 2006 HUMMER H3 2005-2006 Saab 9-7X with 4L60-E, 4L65-E, 4L80-E or 4L85-E Automatic Transmission (RPOs M30, M32, M33, MT1, MN8) 1. With the ignition switch in the RUN position, test for battery voltage at the circuit fuse in the transmission solenoid power supply circuit. Refer to the appropriate SI Document for the transmission solenoid power supply circuit information. 2. If battery voltage is present at the fuse, inspect the ignition voltage circuit between the fuse and the transmission for possible opens. 3. If battery voltage is not present at the fuse, test for continuity between the fuse and the ignition switch. If NO ontinuity is between the fuse and the ignition switch, repair the open in that circuit. 4. If you have continuity between the fuse and the ignition switch, the most likely cause is the ignition switch. Replace the ignition switch using the appropriate Ignition Switch Replacement procedure in SI. Refer to group number 2.188 of the parts catalog for part description and usage of the ignition switch. Warranty Information (excluding Saab U.S. Models) For vehicles repaired under warranty, use: Warranty Information (Saab U.S. Models) For vehicles repaired under warranty, use: Labor Operation Description Labor Time N6630 Wiring and/or Connector, Transmission – Repair Use published labor operation time Labor Operation Description Failed Object Fault/Reason Code Location Code Warranty Type Repair/Action Code Labor Time 3711401 Replace part, Adj., Wiring Harness, A/T Incl. diagnosis time 2005 37114 67 0 01 05 Use published labor operation time

Related Content:

2006 hummer H3 service manual, 2005 buick lacrosse cigar lighter only no power, 2006 hummer h3 ignition switch, 2006 tundra fuse diagram, how to replace a 2005 hummer ingnition switch, ignition fuse for h3, labor time for 01 covette transmission, TIME INSTALLATION OF TRANSMISSION

2000-2006 Toyota Tundra ADVANCED FOLDING COVER INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 01-03-2012

download
Install Rails And Seals 1. There are two rails. Put the rail with the 3rd leg hinge clamp, (Fig.1) with screw facing tailgate, closest to the cab on the bed rail. Make sure the rail is as close as possible to the cab . Remove the two-sided piece of tape and push the rail down. Then, do the same for the other side. ail D seal at end of Tailgate Box Seal It is very important, to have the rail touching the front of the truck box, so the cover can line up correctly. If unable to exactly begin at the front of box, make sure each rail is equal distance away from the front of the box on each side. Check this first, if the cover does not line up correctly. . Next, remove the 10 clamps from your installation kit. To clamp the rail on the truck bed use a 5/16″ socket, wrench or drill then tighten the screws on clamps. Be careful not to over tighten! You must use the one preset spot on each rail (Fig.2). Then space out evenly The first step in installing the Box Seal is to place the guide on the outside of the rail by the cab (Fig 3).Then, remove about 8 inches of the two-sided tape from the Box Seal. Place the Box Seal on the outside of the guide. Start from about an inch from the front and gradually pull the white paper back; push the Box Seal against the guide and rail all the way down the rail, which will give you a perfectly straight seal. Run the seal just past the stake pocket hole and stop, the remaining seal will be trimmed later. Do this on both sides. Finally, remove the white paper on the D-Seal and place it at the end of the rail by the Tailgate (Fig. 4) 1. Place the 3rdleg hinge on the cover, which drops in the key hole bracket (mounted on cover), into the 3rd leg hinge clamp on the rail. The yellow warning sticker on the cover will be facing up. (Fig.5) 2. Step back behind the tailgate and center the cover. Do not center cover to the Box Seal, center the cover to the Truck Bed. 3. Tighten down the screws in both 3rdleg hinge clamps with a 5/16″ socket , wrench or drill. (Fig.6) 4. Undo the four tie downs and unfold the cover over the truck bed. (Fig. 7) For detailed instructions see the yellow sticker under the cover. 5. Tighten the lock nuts on all clamps and both 3rd hinge leg clamps. Use a 3/8″ wrench. (Fig.8)

Related Content:

buick rendezvous glove box removal, how to fix Buick Rendezvous glove, remove glove box buick rendezvous 2006

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, youtube replace the hub on a meritor ff981 axle

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

w584a lincoln, 2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, how to change intake gasket 2007 grandprix, schematic for front brakes on 2005 Buick Rendezvous, 200lolds aleroraditor system, 2007 Chevy Colorado Gas Tank Seal replace, 2007 kia rio service manual, pontiac 2007 g6 remove radiator cover

2001 – 2006 TOYOTA Sequoia BACK DOOR POWER WINDOW INOPERATIVE

0

Filed Under (Toyota Manuals) by admin on 11-01-2012

download
BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 2 of 6 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Plastic Pry Tool Set* NOTE: All components from this kit/set are required 00002-06000-01 1 21 *Essential SSTs. **Refers to drawer number in SST Storage System. NOTE: Additional SSTs may be ordered by calling SPX/OTC at 1-800-933-8335. 1. Disconnect the negative (-) terminal of the vehicle battery. NOTE: Any time the negative (-) battery terminal has been disconnected, systems requiring initialization will need to be re-initialized after the negative (-) battery terminal has been reconnected. 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. Required SSTs Repair Procedure : 5 Clips : 3 Clips BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 3 of 6 5. Remove the strap cover, bolt, and pull strap. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9. 9. For 2005 – 2006 model year Sequoia vehicles ONLY: Remove the multiplex network door ECU. Using a drill of less than 3.2 mm (0.126 in.), drill out the two (2) rivet heads. HINT: Gently and vertically put the drill to the rivets and cut the rivet flanges. CAUTION: Take care as the cut rivets may be HOT. 10. For 2005 – 2006 model year Sequoia vehicles ONLY: Install the replacement multiplex network door ECU and rivets

Related Content:

2006 pt cruiser install guide, 2006 mercury eatc repairs, 2006 kia rio service manual free download, Back Door Power Window Inoperative - EL007-06 - June 14 2006, remove transmission control module G500, where to fine starter location in 2006 chevy calorando, 2006 npr freon capacity, 2006 chevy colorado service manual free, 2006 Chrysler 300c srt8 service and repair manual pdf download, enigine diagram for 2006 grand prix

2006 TOYOTA YARIS ELECTRONIC CRUISE CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 2 of 7 Section II – Installation Procedure A. Pre-Installation Suggestions 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting . (figure 1) 2. Remove driver side small object box, lower dash panel, and steering column cover for easy access. B. Install Electronic Modules 1. There are two electronic modules. The larger one is the Cruise Control Module and the smaller one is the Switch Interface Module . 2. Apply the larger supplied piece of double- sided adhesive tape to the Cruise Control Module, and the smaller piece of double-sided tape to the Switch Interface Module. 3. Assemble 20-pin connector from Main Wiring Harness onto mating connector of Cruise Control Module. Apply the 10 and 4 pin connectors from Pedal Interface Harness to mating connector on Switch Interface Module. Warning: Be sure to use the 4 pin connector that is on the same side of the wire harness fuse as the 10 pin connector. Failure to do so could damage vehicle’s ECM. See the picture insert in Figure 2 for further guidance. 4. Locate the linked harness between the Cruise Control and Switch Interface Modules. Connect the four pin mating connectors. 5. Place the Cruise Control Module on the back side of the main J/B. Then place the Switch Interface Module on the inside wall of the driver-side dash left of the J/B .(figure 2,3) 6. Route the Pedal Interface Harness through steering column and down to the accelerator .(figure 4 ) TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 3 of 7 7. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of the Pedal Interface Harness. Apply the other connector to the accelerator .(figure 5) C. Wiring Connections (figures 6-12) 1. Use the supplied self-stripping connectors (T- taps) from hardware pack to apply a T-tap onto the following J/B wires

Related Content:

what duse is cruise control 2007 volvo xc90, wiring diagram for toyota cressida pdf

1991 Honda Civic Si FUSES AND CIRCUIT BREAKERS Identification

0

Filed Under (Honda Manuals) by admin on 17-05-2011

download
IDENTIFICATION FUSE PANEL LOCATION The fuse box is located under dashboard on driver’s side. Underhood fuse panel is located in engine compartment beside battery. Cars equipped with anti-lock brake system have a third fuse box for ABS in front of the engine compartment on passenger’s side. FUSE PANEL IDENTIFICATION (1988-91) Fig. 1: Fuse Panel Identification (1988-91) Courtesy of AMERICAN HONDA MOTOR CO., INC. Fuse & Circuit Breaker Identification z 1 – 10 Amp Integrated Control Unit, Combination Switch, Gauge Assembly, Back-Up Lights Switch, Shift Position Console Switch, Clock (1990) , Shift Lock Solenoid (1990) , Interlock Control Unit (1990) , 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Honda 1991 Honda Civic Si FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1988-91 Automatic Seat Belts (If Equipped) z 2 – 10 Amp Starter Solenoid, PGM-FI Main Relay, PGM-FI Electronic Control Unit, Integrated Control Unit z 3 – 20 Amp Power Door Locks (If Equipped) z 4 – 10 Amp Right Headlight High Beam, High Beam Indicator Light, Daytime Running Lights Relay (Canada) z 5 – 10 Amp Left Headlight High Beam z 6 – 30 Amp Sun Roof Motor (If Equipped) z 7 – 10 Amp Rear Lights (Canada Only) z 8 – 10 Amp Integrated Control Unit, Interior & Exterior Lighting z 9 – Blank z 10 – 10 Amp Left Headlight Low Beam z 11 – 10 Amp Right Headlight Low Beam z 12 – 15 Amp Integrated Control Unit, Luggage Compartment Light, Dome Light, Ignition Switch, Clock, Radio, Cigarette Lighter z 13 – 15/20 Amp Power Windows, Windshield Wipers & Washer, Sun Roof Relay (1990), Integrated Control Unit (Canada), Combination Switch (1990 CRX) z 14 – 10 Amp Gauge Assembly, Engine Sensors & Controls, PGM-FI Main Relay (Wagon & CRX Only), PGM-FI ECU (Wagon & CRX Only), Fuel Pump (Wagon & CRX Only), ELD Unit (Wagon & CRX Only), EACV (Wagon & CRX Only) z 15 – 15 Amp Cooling Fan Motor (Except 4WD A/T Wagon), Cooling Fan Relay z 16 – 10 Amp Daytime Running Lights (Canada Only) z 17 – 10 Amp Radio, Cigarette Lighter Relay (1990 only) z 18 – 10 Amp Rear Window Defogger, Power Door Mirrors, Air Conditioning z 19 – 30 Amp Blower Motor z 20 – 20 Amp Right Front Power Window z 21 – 20 Amp Left Front Power Window z 22 – 20 Amp Right Rear Power Window z 23 – 20 Amp Left Rear Power Window UNDERHOOD FUSE PANEL IDENTIFICATION (1988-91)

Related Content:

Fuse box honda pilot cigatette lighter, honda civic 09 cigarette lighter fuse, locationof2013sonicfuselocation, 2011 honda pilot fuse identification, bmxa apply chart, inside fuse box 2005 honda civic, 2007 civic main relay locations, 2012 HONDA CRV AUX FUSE LOCATION, mirrors on 2013 rav4 not auto moving fuse location, 1990 corvette intake manual removal

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 18-02-2012

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

Related Content:

2004 buick rendezvous repair manual, service manual for 2004 audi a6 2 7t quattro, 2003 gmc sierra service repair manual, stepper motor for 2004 chevy trailblazer, free 2003 gmc envoy shop manual, repairing the sunroof in a 04 trailblazer, repair manual mitsubishi diamante, 2004 chevy malibu wiring diagrams for EVAP system, programming 2004 tahoe instrument cluster, 2004 envoy cluster self test

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

0

Filed Under (Toyota Manuals) by admin on 22-06-2012

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

Related Content:

2006 pontiac torrent liftgate release switch, 2004 Toyota Sienna Manual PDF, 2004 sienna engine firing order, 2006 cadillac escalade liftgate problem blows fuses, free repair manual for a 2004 toyota sienna, owners manual for a 2006 scion xb, pt cruiser owners manual 2006, replace 2007 pacifica liftgate assists

Related Content:

09 cts air condition drain location, 1990 isuzu npr no power to fuse panel, mercedes benz e280 w211 2005 fuse diagrams, hitatchi ex 200 fuse box order, install 2000 celica air box, land rover freelander 2 2007 fuse box, Popping noise from air filter, replace tacoma ac drain hose, troubleshooting a mazda 6 air conditioner drain line, turn signal fuses on 2002 winnebago adventurer