2006 chevy malibu maxx how to install stereo

You search PDF repair manual about 2006 chevy malibu maxx how to install stereo, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2006 chevy malibu maxx how to install stereo Direct Download speed 5432 Kb/s

  2006 chevy malibu maxx how to install stereo Full Version speed 8172 Kb/s



1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, 2009 ford focus evaporator replacement, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, how to remove the heater core on 2000 VW Beetle, 2004 Buick lesabre inrument cluster removeal, 2003 mitsubishi eclipse replace evapulator, 2002 silverado remove front driveshaft, 2002 ford taurus evap emission line location, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette

2004-2006 Chevrolet Malibu, Malibu Maxx Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap)

0

Filed Under (Chevrolet Manuals) by admin on 10-01-2012

download
Correction Replace the ignition coil/module assembly and add ground strap following the procedure below. 1. Disconnect the ignition coil electrical connector. 2. Disconnect the left side spark plug wires from the ignition coil. 3. Disconnect the right side spark plug wires from the ignition coil. 4. Remove the four bolts attaching the ignition coil to its mounting bracket and remove the ignition coil. 5. Remove the ignition coil from the mounting bracket. 6. Loosen the two lower ignition coil mounting bracket nuts. 7. Remove the two upper ignition coil mounting bracket bolts and discard. Subject: Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) 8. Install the ground strap (1), P/N 12581176, to the upper left side of the bracket as shown between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Prior to installing the ground strap, remove the captured nut and washers. They are not needed (simply pound them out with a hammer on a vise). 9. Install the washer (2), P/N 02436162, to the upper right side of the bracket between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Tighten Tighten all the ignition coil bracket bolts and nuts to 25 N·m (15 lb ft). 10. Install the new ignition coil to the mounting bracket. 11. Install the other end of the ground strap to the coil as shown and secure using a new bolt, P/N 11588715. 12. Install the other three ignition coil bolts. Tighten Tighten the bolts to 10 N·m (89 lb in). 13. Connect the right side spark plug wires to the ignition coil. 14. Connect the left side spark plug wires to the ignition coil. 15. Connect the ignition coil electrical connector

Related Content:

Owners Manual 2004 Chevy Malibu Maxx, malibu ml60t manual, how to replace a ignition coil on 2004 toyota sienna, diagram for ignition wires on a 1998 sebring 2 5l, 1999 saturn replacement ignition switch bolts, repair of saab ignition coil, mazda speed 6 ignition module, 2006 pontiac torrent replacement ignition, 2006 Malibu Maxx Owners Manual, 2006 chevy malibu spark plug lications

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

2006 TOYOTA RAV4 TOWING HITCH INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 17-03-2012

download
TOYOTA RAV4 2006 TOWING HITCH Section II Installation Procedure Page 2 of 7 pages Issue: A 10/11/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Prepare for Installation. (a) Verify kit contents (b) Wear Safety Glasses. (c) Raise Vehicle . (d) Caution Muffler might be hot 2. Remove Rear Bumper Fascia (a) Remove (2) Phillips head screws (A) from both sides of the rear fascia (Fig. 2-1). (b) Remove (7) push pins (A) on edges of fascia (Fig. 2-2) (c) Remove (2) Phillips head screws (B) from bottom of fascia (Fig. 2-2). (d) See Fig. 2-3 for removal of fastener (C). Fig. 2-1 Rear Tire A A (Drivers Side) – Phillips screwdriver A A A A A C A A B B – Phillips screwdriver – Straight shank screwdriver Fig. 2-2 TOYOTA RAV4 2006 TOWING HITCH Section II Installation Procedure Page 3 of 7 pages Issue: A 10/11/05 (e) Remove (1) 10 mm hex head bolt (C) from right hand (RH) side of fascia. (Fig. 2-3) (f) With one person on each end, remove fascia from vehicle. Store in a safe place to avoid damage during installation. 3. Remove Vehicle Tie Down (a) Remove (2) M12 Bolts and vehicle tie down (A) from the left hand (Drivers Side) rear of vehicle (Fig. 3-1). (b) Dispose of bracket and (2) bolts. 4. Detach Muffler (a) Protect exhaust tip with a rag or protective tape during installation of hitch (Fig. 5). (b) Detach muffler from exhaust hangar (Fig. 5) 5. Install Bumper Brackets (a) Remove M8 bolts from the vehicle bumper beam, and install (RH) and (LH) bumper brackets with (3) OE supplied M8 bolts, each with a lock washer and a flat washer (Fig. 5-1). Do not tighten at this time. 6. Install Hitch (a) Lift hitch into place (requires 2 people) and install the (3) M12 x 35 bolts into the (3) weld nuts in the bottom of the frame rails (Fig. 6-1). (b) Loosely secure the middle bolts first, then the (2) forward and aft bolts on each side. (c) Do not tighten bolts at this time. 7. Install Drivers Side Brackets (a) Install LH Frame Bracket (A) to the side of the frame rail using (2) of the M12 x 35 bolts (Fig. 7-1). NOTE: Excess body sealant may require removal of sealant before continuing installation Protect any bare areas with 3MTM Autobody sealant. (b) Install LH Support Bracket (B) to Driver’s Side of Hitch (C), and to bottom of LH Frame Bracket using (4) M12 x 35 bolts. Do not tighten (Fig. 7-1). (c) Fasten LH Support Bracket (B) to LH Bumper Bracket (D) using (4) M12 x 35 bolts. Do not tighten (Fig. 7-1)

Related Content:

how to fix a rav 4 rear bumper, 2006 rav4 front bumper install instrucions, how to replace a rave 4 rear bumper cover, how to install lift supports, HOW TO FIX A DANGLING FRONT SIDE BODY OF TOYOTA RAV4?, how do you remove front bumper 2008 toyota rav4, diy replace 2002 rav 4 rear bumper, 2009-2012 toyota rav4 front bumper removal, 2007 Toyota Rav4 radiator support access cover fastener, installation instructions 2002 rav 4 rear bumper

V8 CHEVY CAMARO HEADER Y-PIPE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Chevy Manuals) by admin on 09-12-2011

download
Disconnect battery. 2. Lift or jack car to a comfortable height. 3. Using WD-40 spray all 6 collector studs and nuts, Y-pipe slip connect, all 4 cat pipe studs & nuts 4. Remove stock Y-pipe by removing the 2 bracket bolts and loosening up the slip connector clamp at rear then remove the 4 nuts holding the Y-pipe to the cat pipes. Slip Y-pipe out, and free from the car. 5. Remove all 4 of the O2 sensors (1) on driver manifold (1) on drive cat pipe (2) on passenger cat pipe. Four total. 6. Remove the 3 nuts on the driver side cat pipe and then remove the 3 nuts on the passenger cat pipe (be careful because the cats are heavy). 7. Remove all 8 spark plug wires. 8. Remove air tube on driver side manifold using a 10 mm socket. 9. Remove air tube on passenger side manifold using a 10 mm socket with universal. 10. Remove EGR tube on passenger side manifold using a 10″ extension with a 10 mm socket and universal. 11. Remove air pump on passenger side of engine and swing out of the way. 12. Remove EGR in front of manifold on top with a 10 mm socket and move to side. 13. Remove dipstick on passenger side 4. Remove all manifold bolts on passenger side and take manifold out. NOTE: Manifolds are Heavy 15. Remove all manifold bolts on driver side and take manifold out. NOTE: Manifolds are Heavy. 16. Unplug electrical hook up on EGR and move out of way. Note: Make sure plug wires are all the way on, and check after installation. Note: Save all stock gaskets, they will be used in installation. INSTALLATION OF BASSANI HEADERS 1. Use Bassani Jet lube on all threads 2. Install the 4 collector studs in headers 2 ea. On each side & snug down. 3. Use the stock exhaust gaskets and install the passenger side header from the bottom and install all of the header bolts then tighten them down after all of them are in. 4. Repeat step 3 for Drivers side. 5. Install the EGR tube on the lower passenger side of the Header. 6. Install the dipstick on Passenger side of engine and put the bolt in. 7. Install plug wires on Passenger side. 8. Install Air tube on Passenger side with supplied 5/16 Hardware. 9. Install EGR to front of motor and plug wire back in. 10. Install EGR tube on top of manifold with 10MM socket. 11. Install the air tube on Drivers side header with supplied 5/16 hardware and Stock Gasket. 12. Install Drivers side spark plug wires, make sure they are all the way on. 13. Install O2 Sensor in Drivers side header and tighten down. 14. Install new Bassani Cat pipe on Drivers side with Jet Lube and supplied 7/16-14 flange nuts and leave loose. 15. Install 2 ea. O2 Sensors in Passenger side Cat pipe

Related Content:

3406 e manual, passenger front side impala 2005

42R Turbo kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 19-03-2012

download
1. Open all boxes and inspect parts and verify from packing list that everything is there. 2. Find Turbo, Header, T4 Gasket, and Waste gates. 3. Carefully remove turbine housing from turbo. 4. Install 10×1.25 stud in location as indicated by picture. 5. Install Gasket and use nuts and bolts with lock washers to secure turbine housing to header.(use anti-seize on threads) 6. Carefully install the rest of the turbo to the turbine housing. Leave the clamps a little loose. (enough to rotate assemblies) 7. Use supplied TiAL gaskets and install waste gates to header. (use anti-seize to lube threads) 8. Install oil feed line to center section and tighten. Rotate center section so the line almost hits the flange and tighten turbine clamp. 9. Install oil return line on center section with gasket. 10. Install water banjo fittings using supplied bolts and washers. 11. Install longer hose on front of turbo and shorter hose on back of turbo. 12. Install assembled turbo on header and tighten all bolts. 13. Install flange on oil pan with gasket use RTV on bolts tighten return line to flange. 14. Install AMS support bracket to block. Twist bolt hand tight against turbine housing then tighten nut securely. – check support bracket bolt every 500 to 1000 miles to make sure it is holding its place properly. 15. Install Downpipe and Secure clamp. 16. Install both dump tubes. Secure passenger side dump tube to bracket on downpipe. Secure drivers side dump tube to threaded hole in compressor housing. 17. Install banjo fitting to cylinder head and secure line. 18. Tighten water lines to stock water lines using supplied clamps. 19. Tighten compressor to center section clamp. 20. Install lower intercooler pipe. 21. Install supplied small radiator kit per instructions. 22. GET TUNED!

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, Need to torque specifications 1999 GMC 1500 wheel hub bearings, snap ring assemble, 2009 impala hub mounting bolt torque, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, 1977 ford f-350 rear wheel diagram, removing rear axle bearing 2002 toyota tacoma, removing rear wheel bearing race in 06 f-250 super duty lariat, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

2007 2008 Toyota Tundra 5.7L dual rear exit aft cat system Installation Manual

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
Installation instructions: 1.) Raise and support vehicle. 2.) Lubricate all factory rubber hangers and fasteners with penetrating oil. 3.) Detach tailpipe from rear of factory muffler and slip hanger rods on tailpipe out of rubber hangers. Remove tailpipe from vehicle. 4.) Remove factory rubber hangers from hanger rods attached to muffler inlet pipes. 5.) Remove factory bolts attaching inlet pipe flanges to vehicle converter pipes; retain stock flange gaskets. 6.) Using stock gasket and bolts, attach supplied left muffler inlet pipe to mating flange of driver side converter pipe. Install factory rubber hanger onto hanger rod welded to pipe. 7.) Using stock gasket and bolts, attach supplied right muffler inlet pipe to mating flange of passenger side converter pipe. Install factory rubber hanger onto hanger rod welded to pipe. 8.) Place supplied 2.25? band clamps over inlets of muffler and install muffler onto inlet pipes with weld seam on muffler body facing up. 9.) Place one supplied 2.5? clamp over inlet of tailpipe section “D” and install pipe onto muffler outlet closest to drive-shaft. Insert hanger rod welded to pipe into corresponding factory rubber hanger just behind muffler 10.) Place one supplied 2.5? clamp over inlet of tailpipe section “E” and install pipe onto outlet of tailpipe section “D”. 11.) Install supplied fabricated hanger bracket, with two attached rods, to bottom of driver side frame rail as shown in Photo no.1. below. Use the supplied 5/16? hardware for attachment; there is an existing hole in frame to use for this purpose. 12.) Place one supplied 2.5? clamp over inlet of tailpipe section “H” and install pipe onto outlet of tailpipe section “D”. 13.) Install one supplied urethane hanger onto the hanger rods welded to the fabricated bracket and tailpipe section “H”. 14.) Place one supplied 2.5? clamp over inlet of tailpipe section “F” and install pipe onto remaining muffler outlet. 15.) Place one supplied 2.5? clamp over inlet of tailpipe section “G” and install pipe onto outlet of tailpipe section “F”. Insert hanger rod on pipe into stock rubber hanger next to spare tire. 16.) Referring to photo no.2 below, remove one stock bumper attachment bolt from each frame rail and replace with supplied 14mm bolts; the bolts closest to the front of the vehicle are the ones which need to be replaced. 17.) Install the supplied left and right tip hangers to the inside of the frame rails and onto the supplied bolts as shown in photo no. 2.; the slots in the brackets will index over the rear-most factory bolts when properly installed. Install the supplied 14mm nuts onto the supplied bolts to retain in place. 18.) Place two remaining 2.5? clamps over tip inlets and install tips onto outlets of tailpipes. 19.) Install remaining urethane hangers between hanger rods on tips and tip brackets attached to frame. Hanger rods on tips will point to the center of vehicle when correctly installed. 20.) Align all components for proper fit and clearance and tighten all clamps.

Related Content:

Rubber muffler hanger for Buick Riviera 95, chevrolet malibu 2007 crossover tube, toyota tundra 2010 spare tire removal, spare tire removal on 2002 tundra, silverado exhaust hanger extensions, section lower rear rail on 02 altima, 2000 bmw heater inlet pipe, removing spare tire from 2004 toyota tundra, how to replce the upper radiator water inlet pipe on a 2001 chevy cavalier, 2007 chevy malibu crossover pipe

2007 Toyota Tundra PRO STEP INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 20-05-2011

download
2 Side Bar Kit – Kit 84801 Before Starting Installation 1. Carefully read all warnings and instructions completely before beginning. 2. Verify all parts have been received in this kit by checking the parts list at the end of this document. 3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3176. 4. Special tools needed: a. 17/64″ drill bit 5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Engine Compartment 1. Disconnect both battery cables. Disconnect negative cable first, then positive cable. 2. Factory Side Bars a. Remove factory side bars if present. NOTE Kit parts are prefaced by the word kit and appear in bold print. NOTE If parts are missing from kit, please be prepared to provide the following information: 1. Name of purchase location 2. Bar Code on side of box 3. Date above bar code 4. Date inside box cover 5. Inspector # from inside box cover Positive Cable Negative Cable Prepare to Install Kit Drivers Side of Vehicle 1. Install kit brackets (body mounted). a. Install two kit brackets (body mounted) along driver side of vehicle using either two factory installed bolts per bracket,.or kit supplied 8mm bolts b. Repeat previous step on pass. side of vehicle. 2. Side Bars a. Insert kit sleeve into kit side bar (rear). Install kit bolt (7/16″ x 1″) and kit washer (7/16 USS flat) into kit sleeve . Underside of Body Kit Bracket Kit Side Bar (front) Short End Kit Side Bar (rear) Long End Side Bar (Passenger Side) Kit Sleeve 3 Side Bar Kit – Kit 84801 b. Install kit side bar (front) onto kit sleeve . Install kit bolt (7/16″ x 1″) and kit washer (3/8 USS flat) into kit sleeve . Install Side Bars on Vehicle 1. Install steps on vehicle a. Install the kit side bar assembly (driver) onto kit body brackets using four kit bolts (1/2″ X 1-1/ 4″), four kit washers (1/2″ flat), four kit sleeves (7/8″ OD), and four kit nuts (flange). Install the kit bolts into the outer holes in the kit body brackets . DO NOT TIGHTEN. NOTE The side bar can be installed in two positions. It can be installed so that the steps are flat or it can be installed with the steps slightly angled downward. Kit bolt (7/16″ x 1″), Kit Washer (3/8 USS flat ) Kit Body Bracket Outer Holes Kit Bolts (1/2 X1-1/4″) b. Determine desired position for the steps. Install four kit bolt (7/16″ x 3 1/2″), four kit washers (7/ 16″), and four kit nuts (flange nut) as indicated below. c. Tighten all mounting bolts on driver side of vehi- cle. d. Repeat for passenger side of vehicle. Install Step Pads on Side Bar 1. Step Pads a. Position kit step pads on center of kit side bar hoop . Ensure the kit step pad is level and mark two locations on each pad to drill

Related Content:

rear camber kit instruction for 07 impala, delphi alternator rebuild kit, owners manual for 1983 kit roadranger, 2006 ford taurus flex pipe repair kit, vacuum windshield wiper model a ford kit repair, installation of Fog Light Assembly 2011 Camry, install cargo net 2014 impala, impala camber kit, repair helicoil for 5 4 liter ford, 2000 blazer frame replacement

2006 – 2008 TOYOTA FJ CRUISER PRO STEP INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 06-03-2012

download
Prepare to Install Kit Drivers Side of Vehicle 1. Install kit driver side front bracket (Frame mounted). NOTE Kit parts are prefaced by the word kit and appear in bold print. NOTE If parts are missing from kit, please be prepared to provide the following information: 1. Name of purchase location 2. Bar Code on side of box 3. Date above bar code 4. Date inside box cover 5. Inspector # from inside box cover a. Locate Factory Side bar mounting Holes on Frame below driver’s door. b. Install one kit Front Mount Bracket and (8mm x 30) bolts & washers . 2. Locate Factory Side bar mounting Holes on Frame below driver’s rear door. Kit Left Front Mount Kit Hanger & Carriage Bolt Left (Drivers Side) Frame Kit, Frame Mount Bracket Kit Left Rear Mount 3 a. Install Kit Rear Mount bracket Left (drivers side).. 3. Repeat Step 1 and 2 for Passenger side of Vehicle (Right). Pro Step Assembly. Install Side Bars on Vehicle 1. Install the kit Pro Step assembly (driver) onto kit body brackets using four kit bolts (1/2″x 1-1/4″) NOTE The side bar can be installed in two positions. It can be installed so that the steps are flat or it can be installed with the steps slightly angled downward. Locate Factory side bar holes in this area of frame left rear. Install kit Rear Mount with kit (8mm x30) bolts & washers. . four kit washers (1/2″ flat), and four kit nuts (flange). a. Tighten all mounting bolts on driver side of vehi- cle. 2. Repeat for passenger side of vehicle. Install Step Pads on Side Bar 1. Step Pads 2. Position kit step pads on kit side bar hoop in desired location. Ensure the kit step pad is level and mark two locations on each pad to drill

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, 2009 ford focus evaporator replacement, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, how to remove the heater core on 2000 VW Beetle, 2004 Buick lesabre inrument cluster removeal, 2003 mitsubishi eclipse replace evapulator, 2002 silverado remove front driveshaft, 2002 ford taurus evap emission line location, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette