2006 commander rear axle solenoid

You search PDF repair manual about 2006 commander rear axle solenoid, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2006 commander rear axle solenoid Direct Download speed 5432 Kb/s

  2006 commander rear axle solenoid Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Torque specs for 2008 prius axle nuts, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, replace shaft seal in AT 2006 Avalon, rearaxleremovamodelaford, remove front diff bearing in navagator, remove rear axle on a 02 mustang

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

0

Filed Under (More Manuals) by admin on 15-06-2012

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Related Content:

2004 ford explorer manual download, Lincoln pa66-gf30 w584a, 2003 ford explorer rear differential removal, removing stuck halfshaft 03 explorer, Free Mercury Mountaineer Repair Manual, free 2002 lincoln ls chilton manual, Ford Five Hundred Repair Manual, 2006 mountainee repair manual, 2006 Ford explorer manual online, 2006 ford explorer manual download

2007 HONDA ODYSSEY SPLASH GUARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 14-10-2011

download
INSTALLATION NOTE: •These instructions show the left splash guards being installed. The same procedure applies to installing the right splash guards. •Clean and wax the areas to be covered with a high-quality paste wax. Installing the Front Splash Guards 1. Turn the steering wheel all the way counter clockwise to provide access to the left front fenderwell. 2. Remove the two self-tapping screws from the left front inner fender. PARTS LIST Right front splash guard Left front splash guard Right rear splash guard Left rear splash guard 6 Self-tapping screws 2 Spring nuts 2 Square head grommets 3. Using a pushpin, make a small hole through the center of the upper clip. UPPER CLIP PUSHPIN SELF-TAPPING SCREW LEFT FRONT INNER FENDER SPLASH GUARDS P/N 08P00-SHJ-101 2 of 2 All 33039-33598 (0608) LEFT REAR SPLASH GUARD SELF-TAPPING SCREW LEFT REAR FENDERWALL SELF- TAPPING SCREW (reused) REAR BUMPER LEFT REAR SPLASH GUARD There must be no clearance. REAR BUMPER LEFT FRONT INNER FENDER LEFT FRONT SPLASH GUARD LEFT FRONT INNER FENDER SELF- TAPPING SCREW LEFT FRONT SPLASH GUARD CLIP CLIP SELF- TAPPING SCREW SELF-TAPPING SCREW (reused) LOWER HOLE 5. While holding the left splash guard against the fender, tighten the self-tapping screws in the order shown. 6. Turn the steering wheel all the way clock wise and repeat steps 2 through 4 to install the right front splash guard. Installing the Rear Splash Guard 7. Using a floor jack, lift up the left rear side of the vehicle according to the service manual. 8. Remove the self-tapping screw from the rear bumper. Using a pushpin, make a hole through the center of the recess. 9. Install one square head grommet into the hole in the left rear fenderwall. Slide one spring nut over the hole you made in step 8 in the rear bumper. 10. Position the left rear splash guard on the left rear fenderwall and rear bumper, and loosely install one self-tapping screw you removed, and the two self-tapping screws supplied with the kit. LEFT REAR FENDERWALL REAR BUMPER SELF-TAPPING SCREW (Reuse.) SQUARE HEAD GROMMET SPRING NUT RECESS PUSHPIN REAR BUMPER With RECESS SELF- TAPPING SCREW 4. Install the left front splash guard using the two self-tapping screws removed in step 2, and one self-tapping screw supplied with the kit. Do not tighten the self-tapping screws yet. 11. Hold the left rear splash guard against the fenderwall and check that there is no clearance between the splash guard and rear bumper. Tighten the three self-tapping screws in the sequence shown. 12. Repeat steps 7 thru 11 to install the right rear splash guard

Related Content:

yhs-fullyhosted_003, how do you replace liftgate relay for 2005 escalade, rear hub assembly removal for 2008 toyota tundra, installation instructions for a 2007 honda accord front bumper, ruff and tuff golf cart parts rear axle bearing, rear cam seal 2000 monterro, Rear brakes 2000 Jag xj8 procedure, rear ac lines on 05 chevy trailblazer, lincoln ls rear suspension squeak, liftgate actuator replacement tahoe

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

1979-1985 Toyota Pick-Up 4WD Superlift 7″ Lift System for INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 24-03-2012

download
INSTALLATION PROCEDURE 1) FRONT OF VEHICLE… â Put the transmission in neutral. Position a floor jack under the front axle and raise vehicle. Place jack stands under the frame rails a few inches behind the spring’s rear shackles. Ease the jack down until the frame is resting in the stands. Keep a slight load on the jack. Put the vehicle in gear or park, set emergency brake and chock rear wheels to prevent any possibility of movement. ââ Remove tires and shocks. Remove the engine belly-pan to gain access to the anti-sway bar. Remove and discard the anti-sway bar assembly. Our spring/shock rate and the bars design render it useless. Reinstall belly-pan. ââ Detach the flexible rubber brake hoses at the calipers only and pinch closed with vise-grips to prevent fluid loss. SEE SEPERATE INSTRUCTIONS. You will install the Superlift hoses later. â Remove the stock drag-link. SEE SEPERATE INSTRUCTIONS. You will install the Superlift link and steering arm later. FORM #7047 .01-080707 PRINTED IN U.S.A. PAGE 2 OF 5 â Remove the bolt attaching the trac-bar (or torque rod) to its bracket on the drivers side of the axle. Unbolt the driveshaft at the front axle and tie it up and out of the way. ââ Remove the spring U-bolts. Ease down the front axle by lowering the jack. The axle vent hose may need rerouting of replacing. Install the Polyurethane bushings into the spring eyes. Lubricate all bushing wear surfaces with light grease. ââ Install the Superlift springs so that the thick end of the degree shims, attached to the bottom of the spring, are pointing towards the front of the vehicle. NOTE: There is a driver (DR) and passenger (PA) side spring. Start, but do not tighten the spring hanger/shackle bolts. ââ Raise the axle up to the springs. Be sure the spring center bolt heads seat properly in the axle perch holes. Attach with the new furnished U-bolts and evenly torque to 131ft. lbs. â Install the superlift Trac-Bar Bracket. â Install the Superlift steering Arm and Adjustable Drag- Link. ââ Install the front Superlift Extended Length Brake Hoses. ââ Install shocks, tires and lower vehicle. ââ With the vehicle weight on the suspension, tighten the front and rear spring hanger bolts. Do not over tighten; tighten only until the bushing flanges compress slightly. 2) REAR OF VEHICLE… NOTE: Before starting, with the vehicle weight on the suspension, rotate the position of the brake proportioning rod where it goes into the proportioning valve; which is located on the passenger side frame rail. On most vehicles, the rod is pretty much horizontal at the attaching point. After the lift is installed, re-bend the rod to its stock position at the proportioning valve. ââ Place a floor jack under the rear axle and raise vehicle. Place jack stands under the frame rails, a few inches in front of the rear springs front hangers. Ease the jack down until the frame is resting on the stands. Keep a slight load on the jack. Chock the front wheels to prevent any possibility of movement. Remove tires, U-bolts and shocks. ââ Disconnect the emergency brake cables at the rear wheels. Lower the axle housing by easing down the jack. Do not overextend the brake and axle vent hoses; both may need rerouting or replacing. If a Superlift rear hose is to be installed detach the stock rubber hose at the axle housing only and pinch closed with vise-grips to prevent fluid loss. You will install the new hose after installing the other rear components

Related Content:

2005 Toyota Avalon Rear Suspension Assembly no 2, wher to place jack stands on 2012 town and country

TOYOTA LANDCRUISER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 10-11-2011

download
INSTALLATION INSTRUCTIONS 1. Park the vehicle on a level surface. Check the vehicle height from side to side and front to back. This is done by measuring from the ground up to the fender using the hub as a centering point. 2. Apply a thin coat of grease to the polyurethane bushings and insert into each eye of the new front springs. Now apply a thin coat of grease on outside of bushings. This will help you to insert the bushing into the spring mount. 3. Raise the front of the vehicle and support securely with jack stands under the frame behind the front springs, and block the rear wheels. Remove the tires, shocks, u-bolts, and loosen the sway bar bolts. (Caution: the front axle will now be free to move, so support securely on floor jack.) 4. With a floor jack supporting the axle, unbolt each end of leaf springs and remove from both sides. (If new shackle bushings were purchased, grease and install them in the frame at this time.) Install new front springs, part # 8041. When installing the front springs that the fat part of the shim on the bottom of the spring pack should be pointing toward the rear of the vehicle. Notice the tie bolt in the front leaf springs is not in the center of the leaf spring, but there is a long end and short end. Install the springs with the short end towards the rear, and long end towards the front bumper. Do not tighten spring eyebolts at this time. 92756702 64-80 TOYOTA LANDCRUISER INSTALLATION
INSTRUCTION SHEET Technical Assistance – (731) 285-9000 Page 2 5. Using the floor jack, lower the front axle down to the leaf springs. Be sure the tie bolts align and fit into the tie bolt holes in the front axle housing. Install and tighten new u-bolts. Torque u-bolts to 75-90 ft.lbs. 6. Install new shocks and tires then lower the vehicle to the ground. Tighten spring eyebolts at this time. NOTE: The drag link that goes along side of the frame from the gear box to the bell crank may require slight bending for clearance of the new shock. Bending this drag link will not affect it, but do not kink the bar. 7. Raise the rear of the vehicle. Support securely with jack stands and block the front wheels. Remove the tires, shocks, and u-bolts. (CAUTION: the rear axle will be free to move, so support securely on a floor jack. 8. Apply a thin coat of grease to the polyurethane bushings and insert into each eye of the new rear springs. Now apply a thin coat of grease on outside of bushings. This will help you to insert the bushing into the spring mount. 9. With a floor jack supporting the rear axle, unbolt each end of the rear leaf spring and remove from both sides. (If new shackle bushings were purchased, grease and install them in the frame at this time.) Install new springs, part # 8042. When installing the rear springs the fat part of the shim on the bottom of the spring pack should be pointing toward the front of the vehicle. Notice the tie bolt in the rear leaf springs is not in the center of the leaf springs, but there is a long end and a short end. Install the springs with the short end towards the front and longer end towards the rear bumper. Do not tighten spring eyebolts at this time. 10. Using a floor jack, lower the rear axle down to the leaf springs. Be sure tie bolts align and fit into the tie bolt holes in the axle housing. Install and tighten new u-bolts, shocks and tires then lower vehicle to the ground. Torque u-bolts to 75-90 ft.lbs. Tighten spring eyebolts at this time.

Related Content:

ford 8 8 rear end rebuild, tahoe balance bar repair, 04 ford f150 8 8 rear end rebulid, replacing a 1997 ford thunderbird rear end, rear for equinox 2005 bolt kit, Meritor Rear Axle Parts Breakdown, how to disassemble 8 inch ford rear axles, grease maintenance for 1997 ford f350, GM 14 BOLT REAREND MANUAL, ford 9 75 rear end specs

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

2006 HONDA CR-V CARGO COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 12-10-2011

download
INSTALLATION Installing the Cargo Cover 1. Open the tailgate. Using a flat-tip screwdriver, remove the panel covers from the right and left rear side trim panels. SUPPLIES REQUIRED Flat-tip screwdriver Clean soft cloth Cargo cover 2 Adhesive tapes 2. Using a clean soft cloth, clean the areas where the panel covers were removed. Remove the adhesive backings from the adhesive tapes, and attach the tapes to the right and left, rear side trim panels where the panel covers were removed. 3. Insert the left end of the cargo cover into the recess in the left rear side trim panel; compress the cargo cover, and insert the right end into the recess in the right rear side trim panel as you release the cover 4. Attach the four front roll cover hooks to the rear seat headrest posts as shown. 5. Slide both ends of the rear roll cover rod into the recesses in the rear side trim panel. Storing the Cargo Cover 6. Insert the right end of the cargo cover into the recess in the right rear side trim panel; compress the cargo cover, and insert the left end into the recess in the left rear side trim panel by compressing the cargo cover, and aligning the end with the recess in the left rear side panel. USE AND CARE •The front roll cover cannot be used when the rear seat is stored. •Do place cargo on the front and rear roll covers. •Do not hang anything from the roll cover hooks. REAR SEAT HEADREST ROLL COVER HOOKS (4) HEADREST STAY CARGO COVER CARGO COVER ROLL COVER ROD

Related Content:

2011 gmc terrain headrest dvds, 2012 honda civic coupe undercarriage cover, 5r55e transmission servo cover blew out AND DAMAGED CASE case, ford 6 0 hpop valve cover torque specifications, install fj cruiser cargo cover

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

0

Filed Under (Toyota Manuals) by admin on 22-06-2012

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

Related Content:

2006 pontiac torrent liftgate release switch, 2004 Toyota Sienna Manual PDF, 2004 sienna engine firing order, 2006 cadillac escalade liftgate problem blows fuses, free repair manual for a 2004 toyota sienna, owners manual for a 2006 scion xb, pt cruiser owners manual 2006, replace 2007 pacifica liftgate assists

2007 Toyota Camry Rear Bumper Removal and Replacement Manual

0

Filed Under (Toyota Manuals) by admin on 26-01-2012

download
REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. INSTALLATION 1. INSTALL REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Engage each claw.

Related Content:

2005 F250 Ford Truck rear brake backing plate, how to remove rear bumper 2008 camry, time it takes to repair front bumper for 2007 toyota camry

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Torque specs for 2008 prius axle nuts, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, replace shaft seal in AT 2006 Avalon, rearaxleremovamodelaford, remove front diff bearing in navagator, remove rear axle on a 02 mustang