2006 f250 front suspension diagram

You search PDF repair manual about 2006 f250 front suspension diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2006 f250 front suspension diagram Direct Download speed 5432 Kb/s

  2006 f250 front suspension diagram Full Version speed 8172 Kb/s



2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose Service Procedure

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud. 1. Replace linkage arms on all three (3) sensor assemblies following Workshop Manual (WSM), Section 204-05. 2. Discard the old linkage arms. NOTE IF THE SENSOR ASSEMBLY NEEDS TO BE REPLACED FOR ANY DAMAGE/FAILURE OTHER THAN THE ONE DESCRIBED IN THIS TSB, THE REPLACEMENT ASSEMBLY IS SUPPLIED WITH A NEW STYLE LINKAGE ARM, SO THERE IS NO NEED TO ORDER ADDITIONAL LINKAGES FOR THE SERVICE REPAIR. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage OPERATION DESCRIPTION TIME 061510A 2003-2006 0.4 Hr. Expedition/Navigator: Replace The Three Linkage Arms, Includes Time To Check Diagnostic Trouble Codes (Do Not Use With 5300A, 5300A7, 5300A8) DEALER CODING CONDITION BASIC PART NO. CODE 5A967

Related Content:

2003 ford explorer front endSUSPENSION ASSEMBLY chematics, 2006 f150 front suspension diagram, air suspension sensor ford, change front struts 2006 gs300, how to repair 03 explorer front control arm, schematic for 2003 lincoln town suspension

1997-2001 FORD EXPEDITION ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE

0

Filed Under (Ford Manuals) by admin on 26-01-2012

download
SUSPENSION, AIR SUSPENSION DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 RIDE HEIGHT RESET PROCEDURE ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE SERVICE PROCEDURE AIR SUSPENSION DTC’S THAT ARE PRESENT NOTE BEFORE ADDRESSING B2140/C2140. DURING PDI (PRE-DELIVERY INSPECTION) IF WARNING “CK SUSP” LIGHT IS ON, PRIOR TO SENDING WARNING: BEFORE REPLACING ANY AIR TO SERVICE, VERIFY SWITCH IN UPPER RIGHT SUSPENSION COMPONENTS, HOISTING, KICK PANEL IS ON. THIS SWITCH IS TURNED JACKING, OR TOWING, DISCONNECT POWER OFF DURING VEHICLE SHIPMENT TO PREVENT TO THE SYSTEM BY TURNING OFF THE AIR MODULE FROM SEEKING TRIM HEIGHT WHILE SUSPENSION SWITCH LOCATED IN THE RIGHT SECURED DOWN FOR TRANSPORT. KICK PANEL AREA TO PREVENT VEHICLE NOTE DAMAGE OR PERSONAL INJURY. AN INADVERTENT B2140 OR C2140 MAY RAS ONLY – CLEAR 2140 RESULT IF A PARAMETER RESET (CLEAR RIDE HEIGHT) IS SELECTED UNDER NGS ACTIVE NOTE COMMANDS, THEN CANCELLED OUT. EVEN RAS (4X2) EQUIPPED VEHICLES REQUIRE STORING RIDE HEIGHT AND NOTE TOGGLING FRONT TO “ON” TO CLEAR A CK THE AIR SUSPENSION CONTROL MODULE SUSP LIGHT/2140 CODE. THIS ALLOWS THE PART NUMBER IS INTERCHANGEABLE MODULE TO STORE THE VOLTAGE WITH NO BETWEEN THE REAR AIR SUSPENSION (RAS) FRONT HEIGHT SENSOR PRESENT, AND MUST AND 4-WHEEL AIR SUSPENSION (4WAS) BE DONE EVEN WITH CONVENTIONAL (STEEL SYSTEMS, BUT ONCE THE MODULE IS COIL) FRONT SUSPENSION. INSTALLED, THE VEHICLE WILL THEN DETERMINE WHETHER VEHICLE IS 4X2 (RAS)

Related Content:

conventional colored front end 2wd suspension diagrams for ford f150 xlt 2001, 99 yukon front suspension diagram, diagram of 2001 chevy blazer front axle, diagram of chrysler 300 front suspension, diagram of front suspension on 2000 ZR2, dodge ram 2500 front suspension diagram 2002, front solenoid code for acura integra 97, hhr rear suspension diagram, How do I replace the spindle bearing on a 1991 Jaguar XJ6, how do you clear DTC codes on 1994 saturn sl1

2001 – 2006 TOYOTA Sequoia BACK DOOR POWER WINDOW INOPERATIVE

0

Filed Under (Toyota Manuals) by admin on 11-01-2012

download
BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 2 of 6 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Plastic Pry Tool Set* NOTE: All components from this kit/set are required 00002-06000-01 1 21 *Essential SSTs. **Refers to drawer number in SST Storage System. NOTE: Additional SSTs may be ordered by calling SPX/OTC at 1-800-933-8335. 1. Disconnect the negative (-) terminal of the vehicle battery. NOTE: Any time the negative (-) battery terminal has been disconnected, systems requiring initialization will need to be re-initialized after the negative (-) battery terminal has been reconnected. 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. Required SSTs Repair Procedure : 5 Clips : 3 Clips BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 3 of 6 5. Remove the strap cover, bolt, and pull strap. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9. 9. For 2005 – 2006 model year Sequoia vehicles ONLY: Remove the multiplex network door ECU. Using a drill of less than 3.2 mm (0.126 in.), drill out the two (2) rivet heads. HINT: Gently and vertically put the drill to the rivets and cut the rivet flanges. CAUTION: Take care as the cut rivets may be HOT. 10. For 2005 – 2006 model year Sequoia vehicles ONLY: Install the replacement multiplex network door ECU and rivets

Related Content:

2006 pt cruiser install guide, 2006 mercury eatc repairs, 2006 kia rio service manual free download, Back Door Power Window Inoperative - EL007-06 - June 14 2006, remove transmission control module G500, where to fine starter location in 2006 chevy calorando, 2006 npr freon capacity, 2006 chevy colorado service manual free, 2006 Chrysler 300c srt8 service and repair manual pdf download, enigine diagram for 2006 grand prix

1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 13-06-2012

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, oem ball joint press, torqe for ball joint 2001 prizm, peugeot 306 front lower arm removal, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000, how to replace a balljoint on a 2002 buick lesabre, 08 silverado lower ball joint removal

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

0

Filed Under (Toyota Manuals) by admin on 22-06-2012

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

Related Content:

2006 pontiac torrent liftgate release switch, 2004 Toyota Sienna Manual PDF, 2004 sienna engine firing order, 2006 cadillac escalade liftgate problem blows fuses, free repair manual for a 2004 toyota sienna, owners manual for a 2006 scion xb, pt cruiser owners manual 2006, replace 2007 pacifica liftgate assists

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

0

Filed Under (More Manuals) by admin on 15-06-2012

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Related Content:

2004 ford explorer manual download, Lincoln pa66-gf30 w584a, 2003 ford explorer rear differential removal, removing stuck halfshaft 03 explorer, Free Mercury Mountaineer Repair Manual, free 2002 lincoln ls chilton manual, Ford Five Hundred Repair Manual, 2006 mountainee repair manual, 2006 Ford explorer manual online, 2006 ford explorer manual download

2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS The mounting procedure outlined below covers the 2000 – 2006 Toyota Tundra trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows: 1. Begin by removing the bolts holding the skid plate to the bottom of the bumper and the rear cross member. Remove the skid plate. Some vehicles are equipped with an additional skid plate that wraps up in front of the bumper. This skid plate must be removed also. 2. Remove the bolts connecting the tow hook, tie down brackets, and skid plate brackets (Refer to Figure 1) to the bottom of the frame. The bolts and tow hook will be used in the undercarriage installation. 3. Assemble Driver Side Push Beam Support Plate (62B) to the bottom of the driver side frame rail. Begin by installing the bolts removed in Step 2 into the two holes in the bottom of Diver Side Push Beam Support Plate (62B) . Tighten these two bolts. Next, drill the inside and outside frame wall for the upper hole in Driver Side Push Beam Support Plate (62B). Install one ½”-13 X 4-1/2″ Hex Head Bolt (D) and one ½”-13 Lock Nut (B) in the drilled hole. Tighten this bolt. 4. Repeat Step 3 on the passenger side frame rail. Include the tow hook over Passenger Side Push Beam Support Plate (62A). The skid plates, tie down brackets, and skid plate brackets (See Figure 1) will no longer be used but should be retained in case the undercarriage is ever removed. 5. Install Push Beam Assembly (62) between Push Beam Support Plates (62A & 62B) using eight ½”-13 X 1-1/2″ Hex Head Bolts (A) and eight ½”-13 Lock Nuts (B). For Light Duty Plow applications, the center of the receiver hole in Push Beam Assembly (62) should be 14-1/2″ from the ground. Leave hardware finger tight. 6. Assemble Angle Bracket (75) to the back of Push Beam Assembly (62) using four ½”-13 X1- 1/2″ Hex Head Bolts (A) and four ½”-13 Lock Nuts (B). Leave hardware finger tight. 3 7. Assemble the rear portion of Angle Bracket (75) to the truck’s cross member using two Nut Plates (101), two ½” Split Lock Washers (C) and two ½”-13 X 1-1/2″ Hex Head Bolts (A) . Nut Plates (101) must be inserted into the cross member through the large hole in the rear of the cross member. 8. Tighten all hardware beginning at the rear of Angle Bracket (75) and working forward. 9. With all undercarriage parts in place, securely fasten all mounting hardware. It is important that all fasteners be properly torqued (see Fig. 3) to assure a safe operating plow. Re-tighten all fasteners after 2 hours of plowing.

Related Content:

diagram of 2006 honda oddessey, how to remove skid plate on 2012 tundra, removing Driveshaft 2006 Tundra

2006 TOYOTA RAV4 TOWING HITCH INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 17-03-2012

download
TOYOTA RAV4 2006 TOWING HITCH Section II Installation Procedure Page 2 of 7 pages Issue: A 10/11/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Prepare for Installation. (a) Verify kit contents (b) Wear Safety Glasses. (c) Raise Vehicle . (d) Caution Muffler might be hot 2. Remove Rear Bumper Fascia (a) Remove (2) Phillips head screws (A) from both sides of the rear fascia (Fig. 2-1). (b) Remove (7) push pins (A) on edges of fascia (Fig. 2-2) (c) Remove (2) Phillips head screws (B) from bottom of fascia (Fig. 2-2). (d) See Fig. 2-3 for removal of fastener (C). Fig. 2-1 Rear Tire A A (Drivers Side) – Phillips screwdriver A A A A A C A A B B – Phillips screwdriver – Straight shank screwdriver Fig. 2-2 TOYOTA RAV4 2006 TOWING HITCH Section II Installation Procedure Page 3 of 7 pages Issue: A 10/11/05 (e) Remove (1) 10 mm hex head bolt (C) from right hand (RH) side of fascia. (Fig. 2-3) (f) With one person on each end, remove fascia from vehicle. Store in a safe place to avoid damage during installation. 3. Remove Vehicle Tie Down (a) Remove (2) M12 Bolts and vehicle tie down (A) from the left hand (Drivers Side) rear of vehicle (Fig. 3-1). (b) Dispose of bracket and (2) bolts. 4. Detach Muffler (a) Protect exhaust tip with a rag or protective tape during installation of hitch (Fig. 5). (b) Detach muffler from exhaust hangar (Fig. 5) 5. Install Bumper Brackets (a) Remove M8 bolts from the vehicle bumper beam, and install (RH) and (LH) bumper brackets with (3) OE supplied M8 bolts, each with a lock washer and a flat washer (Fig. 5-1). Do not tighten at this time. 6. Install Hitch (a) Lift hitch into place (requires 2 people) and install the (3) M12 x 35 bolts into the (3) weld nuts in the bottom of the frame rails (Fig. 6-1). (b) Loosely secure the middle bolts first, then the (2) forward and aft bolts on each side. (c) Do not tighten bolts at this time. 7. Install Drivers Side Brackets (a) Install LH Frame Bracket (A) to the side of the frame rail using (2) of the M12 x 35 bolts (Fig. 7-1). NOTE: Excess body sealant may require removal of sealant before continuing installation Protect any bare areas with 3MTM Autobody sealant. (b) Install LH Support Bracket (B) to Driver’s Side of Hitch (C), and to bottom of LH Frame Bracket using (4) M12 x 35 bolts. Do not tighten (Fig. 7-1). (c) Fasten LH Support Bracket (B) to LH Bumper Bracket (D) using (4) M12 x 35 bolts. Do not tighten (Fig. 7-1)

Related Content:

how to fix a rav 4 rear bumper, 2006 rav4 front bumper install instrucions, how to replace a rave 4 rear bumper cover, how to install lift supports, HOW TO FIX A DANGLING FRONT SIDE BODY OF TOYOTA RAV4?, how do you remove front bumper 2008 toyota rav4, diy replace 2002 rav 4 rear bumper, 2009-2012 toyota rav4 front bumper removal, 2007 Toyota Rav4 radiator support access cover fastener, installation instructions 2002 rav 4 rear bumper

2006 TOYOTA YARIS ELECTRONIC CRUISE CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 2 of 7 Section II – Installation Procedure A. Pre-Installation Suggestions 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting . (figure 1) 2. Remove driver side small object box, lower dash panel, and steering column cover for easy access. B. Install Electronic Modules 1. There are two electronic modules. The larger one is the Cruise Control Module and the smaller one is the Switch Interface Module . 2. Apply the larger supplied piece of double- sided adhesive tape to the Cruise Control Module, and the smaller piece of double-sided tape to the Switch Interface Module. 3. Assemble 20-pin connector from Main Wiring Harness onto mating connector of Cruise Control Module. Apply the 10 and 4 pin connectors from Pedal Interface Harness to mating connector on Switch Interface Module. Warning: Be sure to use the 4 pin connector that is on the same side of the wire harness fuse as the 10 pin connector. Failure to do so could damage vehicle’s ECM. See the picture insert in Figure 2 for further guidance. 4. Locate the linked harness between the Cruise Control and Switch Interface Modules. Connect the four pin mating connectors. 5. Place the Cruise Control Module on the back side of the main J/B. Then place the Switch Interface Module on the inside wall of the driver-side dash left of the J/B .(figure 2,3) 6. Route the Pedal Interface Harness through steering column and down to the accelerator .(figure 4 ) TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 3 of 7 7. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of the Pedal Interface Harness. Apply the other connector to the accelerator .(figure 5) C. Wiring Connections (figures 6-12) 1. Use the supplied self-stripping connectors (T- taps) from hardware pack to apply a T-tap onto the following J/B wires

Related Content:

what duse is cruise control 2007 volvo xc90, wiring diagram for toyota cressida pdf

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

Related Content:

2003 ford explorer front endSUSPENSION ASSEMBLY chematics, 2006 f150 front suspension diagram, air suspension sensor ford, change front struts 2006 gs300, how to repair 03 explorer front control arm, schematic for 2003 lincoln town suspension