Skip to content

2006 hhr evap

You search PDF repair manual about 2006 hhr evap, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

2006 Ford F-SUPER DUTY Class A Motorhome Chassis INCOMPLETE VEHICLE MANUAL

download
Certain exhaust system components, including exhaust heat shielding systems, have been installed on some vehicles in our assembly plants in an effort to provide protection against engine compartment and exhaust system temperatures. Subsequent aftermarket installers/manufacturers are responsible for providing thermal protection (e.g. underbody heat shields) for any structure and/or equipment added to the vehicle and should not remove any components or exhaust heat shielding installed on the vehicle by Ford Motor Company. All exposed interior sheet metal of closed structures (e.g. fl oor pan of cab and/or secondary structure, tool boxes, etc.) should be covered with an insulating material capable of protecting vehicle occupants and contents from temperatures potentially up to 700°F. OZONE DEPLETING SUBSTANCE (ODS) OZONE DEPLETING SUBSTANCE (ODS) The Clean Air Act of 1990, Section 611 requires any product (i.e., completed vehicle) containing or manufactured with any Class I Ozone Depleting Substance on, or after May 15,1993 must be identifi ed with a “clearly and conspicuously attached label.” Ford Motor Company has eliminated Class I ODS from its manufacturing processes. All 2006 Ford Truck incomplete vehicles will not have Class I ODS content. Manufacturers, including subsequent stage manufacturers, are required to label their products if the product, including any component (whether manufactured by that manufacturer or not), contains a Class I ODS or if the manufacturer used a Class I ODS in the manufacturing of the product. In the case where Ford Motor Company provides a label saying the incomplete vehicle contains a Class I ODS that information must be placed on the product warning label. (See EPA regulation on wording, placement, size, and combining labels.) In Canada consult the appropriate Provincial or Territorial Ministry of Environment. EMISSION CONTROL INFORMATION LABEL To meet United States Environmental Protection Agency regulations, the Important Vehicle Information (tune-up and fuel tank capacity) labels must be affi xed in a location that is readily visible after installation and in such a manner that it cannot be removed without destroying or defacing the label. The label shall not be affi xed to any equipment that is easily detached from the vehicle. When emission control labels are supplied but not attached to the vehicle (i.e., tune-up label or fuel tank label), they must be permanently mounted in a readily visible location to meet the preceding requirements. In addition, whether the label is already affi xed or to be affi xed, no components shall be installed which visibly obscure the label in any way that fails to satisfy the visibility requirements described in the California Emission Control Label Specifications. For Canadian requirements consult Section 1100 8 (1) (d) (i), (ii), & (iii). CALIFORNIA FUEL VAPOR RECOVERY California regulations require that the vehicle fuel systems be designed to accommodate a vapor recovery fueling nozzle including unobstructed access to the fi ll pipe. Fuel fi ller pipes installed per the Figure B on page 15 will comply with the “Specifi cations For Fill Pipes and Openings of Motor Vehicle Fuel Tanks” referenced in Title 13 California Administrative Code provided no part of the aftermarket body, as installed, intrudes within a 254mm [10 in] radius cylinder which has its axis parallel to the ground at point “Z” and extends outward from the Ford Motor Company supplied fuel pipe housing component. The fuel pipe housing component is shown on the referenced fi gures and is attached to the aftermarket body via 4.76 mm [.188 in.] diameter rivets. Fuel fi ller pipes installed using the alternative bracket shown in Figure B, will comply with the above California vapor recovery regulations provided the aftermarket body does not interfere with the access zone as defi ned by the California Air Resources Board, and the areas adjacent to this opening cannot foreseeably damage the nozzle bellows or face plate of nozzles during insertion, latching, disposing or removal

DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit)

download
Tighten Tighten the bracket mounting bolt to 12 N?m (106 lb in). Connect the vent valve pipe to the EVAP canister. • Install the two vent valve pipe clips into the existing underbody holes. • Connect the EVAP canister vent valve electrical connector, if equipped. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. • Remove the transmission support and lower the transmission assembly as necessary to allow for access to the new filter box location using a tie strap. DO NOT pinch or restrict the transmission vent hose. The filter box opening should be pointing downward. • Raise the transmission and reinstall the transmission support. • Tie strap the hose as needed along the frame rail in order to keep the hose away from pinch*points and heat sources. • Lower the vehicle. • 2004-2007 Model Year (Use Service Kit P/N 19152349) Raise the vehicle. Suitably support the vehicle. • Disconnect the EVAP canister vent valve electrical connector. • Disconnect the canister pipe from the vent valve. • Push in the retainer and remove the existing canister vent valve from the fuel tank clip or mounting bracket. Discard the old valve. • Cut back the existing canister pipe approximately 51 mm (2 in) to remove the quick connect end. Crew Cab Short Box Shown Below, Other Configurations Similar Extended Cab Short Box Shown Below, Other Configurations Similar Install the new canister vent valve to the fuel tank clip or mounting bracket. • Cut bulk 5/8″ heater hose to a length of approximately 76 mm (3 in). Install the hose between the vent valve and the canister pipe and secure using clamps. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. •