2006 mazda 6s water pump replacement

You search PDF repair manual about 2006 mazda 6s water pump replacement, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2006 mazda 6s water pump replacement Direct Download speed 5432 Kb/s

  2006 mazda 6s water pump replacement Full Version speed 8172 Kb/s



1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, lucas cav injection pump diagram, 2002 isx cummins manual pump installation, rager injection pump parts manual, cav injector pump governor spring, how to change water pump on a dewoo, isuzu dmax fuel pump, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, 89 dodge dakota fuel pump diagram, mitsubishi 6d22c governor ajustment

2004 Mazda 6 i Engine Mechanical WATER PUMP DRIVE BELT

0

Filed Under (Mazda Manuals) by admin on 09-06-2011

download
1. Verify that the water pump drive belt auto tensioner indicator mark does not exceeds the limit. ? If it exceeds the limit, replace the water pump drive belt. (See WATER PUMP DRIVE BELT .) Fig. 20: Water Pump Drive Belt Auto Tensioner Limit Indicator Mark – Normal WATER PUMP DRIVE BELT 1. Remove the plug hole plate. 2. Rotate the water pump drive belt auto tensioner counterclockwise to release the drive belt tension and remove the water pump drive belt. 3. Reinstall the water pump drive belt or install a new water pump drive belt. WATER PUMP DRIVE BELT PULLEY REMOVAL NOTE 1. Replace part A of the SST [303-009 (49 UN30 3009)] with the SST [303-457 (49 UN30 3457)].

Related Content:

2004 dodge neon water pump installation, 2004 dodge neon waterpump replacement directions, 2004 envoy water pump replacement, how to replace a water pump on 2004 dodge neon, replace water pump on 2004 Kia reo, replacing a water pump 2004 v=6 mazda, water pump 2004 neon

Troubleshooting and Resolving Water Leaks for FUNSPORT Sunroofs

0

Filed Under (More Manuals) by admin on 13-03-2012

download
1. Opening the sunroof, just after it rains. Standing water on the glass will usually result in water dripping into the cabin. This is not a sunroof fault. Prevention is the solution! Simply drive a short distance to allow any standing water to blow off the glass prior to opening the sunroof. 2. Only after a car wash. High pressure water sprayed directly at the seal will often deflect the seal enough to enter the cabin. This is not a sunroof fault. Prevention is the solution! Don’t spray high pressure water directly on the seal. 3. During a rainstorm, water is immediately visible dripping on the rubber seal under the glass. There may be a problem with glass to seal contact. Carefully examine the seal. If it is visibly damaged or worn, it may need replacement. If dirty, it needs cleaning. An adjustment may solve the problem. Always water test to verify (see sprinkle test procedure below). a. Often dirt or debris will prevent proper contact between the glass and seal. Clean both the glass and seal with plain water (a damp cloth), or if very dirty, a mild detergent solution. Repeat water test after cleaning. If water intrusion between glass and seal continues, adjust the glass hardware. b. Adjust the glass hardware to increase clamping pressure on the seal. See procedure below. Repeat water test after adjusting. If water intrusion between glass and seal continues, replace seal. 4. Water is visible dripping through the glass hardware: Water test to verify (soak and sprinkle). You may need to slightly shift the glass hardware or change the rubber gaskets under the rectangular mounting plates. 5. After a long soaking rain the headliner gets wet. This is likely the result of water coming under the main frame or under the seal. Only a soak test will prove this. a. Under the main frame: remove the screw cover strip or pull back the headliner (of wrapped) and examine the clamping screws. Water spots or rusty screws are an indication that water is coming under the main frame. Remove the clamp frame and water spots or rust will likely be visible on the inside of the roofskin. This can be the result of an over-cut hole, a sunroof not centered on the hole (left a gap) or inadequate sealant. Solution: Remove the sunroof and re-install with new sealant. If the hole was over-cut, a larger size may be required. b. Underneath the main seal: carefully examine and verify proper seal insertion around perimeter of sunroof frame. Bottom of seal should be adhered to main frame with butyl tape. Top outer lip should be mechanically inserted into groove in frame. You may be able to manipulate the seal slightly to correct the problem. Otherwise replace the seal. c. Frame joint: typically will see water spots or rust on hinge block and handle mounting screws, particularly on the right hand side. Remove the knock-in bead and examine the channel for water or water spots. Solution: pull back the main seal at the passenger side and apply a small amount of silicone sealant across the frame joint. Allow to dry before reinserting the main seal.

Related Content:

1997 lumina 3 1l thermostat adjustment dial?, seal for slip on muflers, how to seal compresion hose leak on 2000 bmw 528i, rear main seal leak 2006 suburban, rear seal replacement on 2003 Chevy Cavalier, reinstall 1929 ford rear glass replacement, removing axles 1998 ford expedition, Replacing rear main seal 2003 suburban, ridgeline rear main seal tsb, to change seal on 2003 camshaft sensor

1995 Nissan-Datsun Maxim Water Pump Service and Repair REMOVAL AND INSTALLATION

0

Filed Under (Nissan Manuals) by admin on 03-06-2011

download
1.Drain coolant from drain plugs on radiator and both sides of cylinder block. 2.Remove drain plug on cylinder block. 3.Remove right side engine mounting, mounting bracket and nuts. 4.Remove drive belts and idler pulley bracket. 5.Remove chain tensioner cover and water pump cover. 6.Pushing timing chain tensioner sleeve, apply a stopper pin so it does not return. Then remove the chain tensioner assembly. 7.Remove the 3 water pump fixing bolts. Secure a gap between water pump gear and timing chain, by turning crankshaft pulley 2O° backwards. 8.Put M8 bolts to two M8-threaded holes out of 3 water pump fixing bolt holes 9.Tighten M8 bolts by turning half turn alternately until they reach timing chain rear case. In order to prevent damages to water pump or timing chain rear case, do not tighten one bolt continuously. Always turn each bolt half turn each time. 10.Lift up water pump and remove it. When lifting up water pump, do not allow water pump gear to hit timing chain. INSPECTION 1.Check for badly rusted or corroded body assembly. 2.Check for rough operation due to excessive end play. INSTALLATION 1.Before installing, remove all traces of liquid gasket from mating surface of water pump cover and chain tensioner cover using a scraper. Also remove traces of liquid gasket from mating surface of front cover. 2.Apply a continuous bead of liquid gasket to mating surface of chain tensioner cover and water pump cover. 3.Return the crankshaft pulley to its original position by turning it 2O° forward. 4.Install timing chain tensioner, then remove the stopper pin After installing the tensioner, race the engine at about 3,000 rpm under no load to purge air from the high-pressure chamber. The engine may produce a rattling noise. This indicates that air still remains in the chamber and is not a matter of concern. 5.Install drain plug on cylinder block. 6.Reinstall any parts removed in reverse order of removal

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

wire diagram on a 2002 grand prix headlight, 1998 jimmy fuel pump install, 03 ford windstar fuel pump wiring, vcm ground wire, pontiac grand am fuel pump wireing harness replacement instructions, proper connection for horn relay 1968 chevelle, 2005 tundra speed pulse signal wire location, fan cable for 1998 dodge caravan, location of vent valve solenoid on 2010 ford ranger, 86 corvette wiring schematics

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2005 yukon xl blend door problems, 2009 focus exterior door hand replacing, how to remove a 2009 chev avalanche door panel, volvo penta impeller replacement instructions, 2008 malibu driver door lock actuator assy, F150 Blend Door Actuator Replacement, gmc valve lifter guide, replace lh front door regulator on 2002 explorer, how to replace power door lock 01 s10

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, where is the washer relay located in a 2009 chevy impala, where is the relay switch for liftgate in 2005 esclade, g5 sunroof relay, 1993 corvette power seat and power window shorting out breaker, 99 eldorado fuel pump relay test, l wiper delay control modual for85 ford thunderbird

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT (3.1 L) MANUAL

0

Filed Under (Pontiac Manuals) by admin on 08-05-2012

download
THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) Fig. 74: Radiator Inlet Hose & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. Fig. 75: Water Outlet Housing & Bolts Courtesy of GENERAL MOTORS CORP. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces Fig. 76: Thermostat & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the thermostat. 3. Install the water outlet housing bolts. Tighten Tighten the water outlet housing bolts to 25 N.m (18 Ib ft). 4. Install the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) . 5. Install the radiator inlet hose to the water outlet housing.

Related Content:

replacing thermostat izusu axiom, 2001 oldsmobile alero 3 4l thermostat removal, 2002 concorde themostat diagram, 2002 pontiac grandprix 3 8 thermostat replacement, 99 explorer changing thermostat, Car Thermostat Diagrams 2008 Pontiac G6, how do you change a intake gasket on a 2001 pontiac grand prix gt, where is the thermostat in a sienna 2005, where is thethermostate on a pontaic mini van

1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 06-01-2012

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.

Related Content:

differential service procedures, 2006 suburban oil pump replcement procedure, picture of 1997 4x4 honda passport axle warning lights, 1997 dodge ram 4x4 1500 service manual download, oil pump leak 2003 accord, oil pump on a 307, oil punp removal 2002 trailblazer, rav4 rear oil leak, Toyota 4 Y oil pump, what causes 147 transaxle code on 97 e420 mercedes

Malfunction Indicator Lamp (MIL) Illuminated, DTCs P0300-P0306, Engine Runs Rough (Inspect for Water Intrusion in Spark Plug Recess Area, Replace Spark Plug and Ignition Coil, Seal Ign Coil Bolt Hole)

0

Filed Under (More Manuals) by admin on 18-01-2012

download
1. Observe the Misfire Current Counters parameter with a scan tool, in order to determine the affected cylinder(s). 2. Remove the air cleaner resonator and outlet duct. Refer to Air Cleaner Resonator and Outlet Duct Replacement in SI. 3. Disconnect the engine wiring harness electrical connectors from the affected ignition coil(s). Refer to Ignition Coil Replacement in SI. 4. Remove the ignition coil bolt(s) and ignition coil(s) from the camshaft cover. Refer to Ignition Coil Replacement in SI. Note: If water is observed in ANY of the spark plug recess areas, then it will be necessary to apply Loctite® 565 PST Thread Sealant* to ALL of the ignition coil bolt hole vents and bolt threads. 5. Inspect for water intrusion in the spark plug recess areas. Warning: Wear safety glasses when using compressed air, as flying dirt particles may cause eye injury. 6. If any water is present, then remove the water from the spark plug recess areas with low pressure air. 7. Remove the affected spark plug(s) from the cylinder head. Refer to Spark Plug Replacement in SI. 8. Replace ONLY the affected spark plug(s) with new spark plug(s) as needed into the cylinder head. Refer to Spark Plug Replacement in SI. 9. Fill the bottom of the ignition coil bolt hole vent with Loctite® 565 PST Thread Sealant* as indicated in the illustration, and apply it to the ignition coil bolt threads also. 10. Replace ONLY the affected ignition coil(s) with new ignition coil(s) as needed. Refer to Ignition Coil Replacement in SI. 11. Connect the engine wiring harness electrical connectors to the ignition coil(s). Refer to Ignition Coil Replacement in SI. 12. Replace the air cleaner resonator and outlet duct. Refer to Air Cleaner Resonator and Outlet Duct Replacement in SI. 13. Clear the DTCs with a scan tool.

Related Content:

07 g5 ignition housing, 09 chevy silverodo how to replace ignition lock cylinder, 1991 ford explorer ignition cylinder disasembly, 2002 crv ignition lock replacement, 2007 chevy suburban cylinder diagram, ford taurus ignition cylinder repair, ignition cylinder lock FOR KIA DIAGRAM, toyota avalon spark plug 2005

Related Content:

99 subaru forester fuel line repair kits, lucas cav injection pump diagram, 2002 isx cummins manual pump installation, rager injection pump parts manual, cav injector pump governor spring, how to change water pump on a dewoo, isuzu dmax fuel pump, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, 89 dodge dakota fuel pump diagram, mitsubishi 6d22c governor ajustment