Skip to content

2006 saturn ion 2 manual

You search PDF repair manual about 2006 saturn ion 2 manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Honda Navigation System Information and DVD Information and Inspection Manual

REVISION SUMMARY •Under BACKGROUND, more sources for navigation service and user information are listed. •Under DVD LABEL COLOR IDENTIFICATION BY MODEL, the Latest DVD Version available is updated. •Under REPLACING THE NAVIGATION CONTROL UNIT AND TRANSFERRING THE NAVIGATION DVD, a step was added to Save Users Memory when replacing the navigation control unit. •Under ENTERING THE ANTI-THEFT CODE, the instructions about obtaining the serial number from a navigation unit without removing it were clarified. •Under NAVIGATION SYSTEM PLATFORMS, HFL was added to the list of Distinguishing Features . BACKGROUND Use this information to avoid possible customer dissatisfaction issues caused by incorrect or outdated DVD installation. For more information about the navigation system and its operation, refer to the following resources: •Service Manual – Printed or on ISIS •Quick Start Guide •Online University – Use the keyword NAVI . •Navigation System Manual – Besides the one that comes with the vehicle, the navigation system manual is also available online. Select SEARCH BY PUBLICATION , select Consumer Information , select your applicable vehicle, then select Navigation Manual from the list. •Service Bulletins – Use the keyword NAVI . •ETM (electrical troubleshooting manual) This bulletin provides the following navigation system DVD service information: •DVD label color identification by model •Earliest DVD version application for each model •How to identify navigation DVD versions •Checking a DVD for damage •Ordering a DVD •Navigation DVD stocking concerns •DVD handling and cleaning •Installing a navigation DVD •Precaution on customer “sneak previews” of a newer navigation DVD version •Answering customer questions about navigation coverage and POI (point of interest) •Pitfalls when interchanging navigation DVD/parts during diagnosis •Replacing the navigation control unit and transferring the navigation DVD •Entering the anti-theft code •Navigation system platforms VEHICLES AFFECTED • 2003-09 Accord • 2005-07 Accord Hybrid • 2006-09 Civic • 2006-09 Civic Hybrid • 2007-09 CR-V • 2009 Element • 2009 Fit • 2000-09 Odyssey • 2003-09 Pilot • 2006-09 Ridgeline WARRANTY CLAIM INFORMATION None. This service bulletin is for information only. Refer to the flat rate manual whenever servicing or repairing the navigation system

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.


FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.


Certain exhaust system components, including exhaust heat shielding systems, have been installed on some vehicles in our assembly plants in an effort to provide protection against engine compartment and exhaust system temperatures. Subsequent aftermarket installers/manufacturers are responsible for providing thermal protection (e.g. underbody heat shields) for any structure and/or equipment added to the vehicle and should not remove any components or exhaust heat shielding installed on the vehicle by Ford Motor Company. All exposed interior sheet metal of closed structures (e.g. fl oor pan of cab and/or secondary structure, tool boxes, etc.) should be covered with an insulating material capable of protecting vehicle occupants and contents from temperatures potentially up to 700°F. OZONE DEPLETING SUBSTANCE (ODS) OZONE DEPLETING SUBSTANCE (ODS) The Clean Air Act of 1990, Section 611 requires any product (i.e., completed vehicle) containing or manufactured with any Class I Ozone Depleting Substance on, or after May 15,1993 must be identifi ed with a “clearly and conspicuously attached label.” Ford Motor Company has eliminated Class I ODS from its manufacturing processes. All 2006 Ford Truck incomplete vehicles will not have Class I ODS content. Manufacturers, including subsequent stage manufacturers, are required to label their products if the product, including any component (whether manufactured by that manufacturer or not), contains a Class I ODS or if the manufacturer used a Class I ODS in the manufacturing of the product. In the case where Ford Motor Company provides a label saying the incomplete vehicle contains a Class I ODS that information must be placed on the product warning label. (See EPA regulation on wording, placement, size, and combining labels.) In Canada consult the appropriate Provincial or Territorial Ministry of Environment. EMISSION CONTROL INFORMATION LABEL To meet United States Environmental Protection Agency regulations, the Important Vehicle Information (tune-up and fuel tank capacity) labels must be affi xed in a location that is readily visible after installation and in such a manner that it cannot be removed without destroying or defacing the label. The label shall not be affi xed to any equipment that is easily detached from the vehicle. When emission control labels are supplied but not attached to the vehicle (i.e., tune-up label or fuel tank label), they must be permanently mounted in a readily visible location to meet the preceding requirements. In addition, whether the label is already affi xed or to be affi xed, no components shall be installed which visibly obscure the label in any way that fails to satisfy the visibility requirements described in the California Emission Control Label Specifications. For Canadian requirements consult Section 1100 8 (1) (d) (i), (ii), & (iii). CALIFORNIA FUEL VAPOR RECOVERY California regulations require that the vehicle fuel systems be designed to accommodate a vapor recovery fueling nozzle including unobstructed access to the fi ll pipe. Fuel fi ller pipes installed per the Figure B on page 15 will comply with the “Specifi cations For Fill Pipes and Openings of Motor Vehicle Fuel Tanks” referenced in Title 13 California Administrative Code provided no part of the aftermarket body, as installed, intrudes within a 254mm [10 in] radius cylinder which has its axis parallel to the ground at point “Z” and extends outward from the Ford Motor Company supplied fuel pipe housing component. The fuel pipe housing component is shown on the referenced fi gures and is attached to the aftermarket body via 4.76 mm [.188 in.] diameter rivets. Fuel fi ller pipes installed using the alternative bracket shown in Figure B, will comply with the above California vapor recovery regulations provided the aftermarket body does not interfere with the access zone as defi ned by the California Air Resources Board, and the areas adjacent to this opening cannot foreseeably damage the nozzle bellows or face plate of nozzles during insertion, latching, disposing or removal