Skip to content

2006 tundra manual pdf

You search PDF repair manual about 2006 tundra manual pdf, if there are search results will appear below. If search results do not exist, please search by others keyword.

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS

download
2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS The mounting procedure outlined below covers the 2000 – 2006 Toyota Tundra trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows: 1. Begin by removing the bolts holding the skid plate to the bottom of the bumper and the rear cross member. Remove the skid plate. Some vehicles are equipped with an additional skid plate that wraps up in front of the bumper. This skid plate must be removed also. 2. Remove the bolts connecting the tow hook, tie down brackets, and skid plate brackets (Refer to Figure 1) to the bottom of the frame. The bolts and tow hook will be used in the undercarriage installation. 3. Assemble Driver Side Push Beam Support Plate (62B) to the bottom of the driver side frame rail. Begin by installing the bolts removed in Step 2 into the two holes in the bottom of Diver Side Push Beam Support Plate (62B) . Tighten these two bolts. Next, drill the inside and outside frame wall for the upper hole in Driver Side Push Beam Support Plate (62B). Install one ½”-13 X 4-1/2″ Hex Head Bolt (D) and one ½”-13 Lock Nut (B) in the drilled hole. Tighten this bolt. 4. Repeat Step 3 on the passenger side frame rail. Include the tow hook over Passenger Side Push Beam Support Plate (62A). The skid plates, tie down brackets, and skid plate brackets (See Figure 1) will no longer be used but should be retained in case the undercarriage is ever removed. 5. Install Push Beam Assembly (62) between Push Beam Support Plates (62A & 62B) using eight ½”-13 X 1-1/2″ Hex Head Bolts (A) and eight ½”-13 Lock Nuts (B). For Light Duty Plow applications, the center of the receiver hole in Push Beam Assembly (62) should be 14-1/2″ from the ground. Leave hardware finger tight. 6. Assemble Angle Bracket (75) to the back of Push Beam Assembly (62) using four ½”-13 X1- 1/2″ Hex Head Bolts (A) and four ½”-13 Lock Nuts (B). Leave hardware finger tight. 3 7. Assemble the rear portion of Angle Bracket (75) to the truck’s cross member using two Nut Plates (101), two ½” Split Lock Washers (C) and two ½”-13 X 1-1/2″ Hex Head Bolts (A) . Nut Plates (101) must be inserted into the cross member through the large hole in the rear of the cross member. 8. Tighten all hardware beginning at the rear of Angle Bracket (75) and working forward. 9. With all undercarriage parts in place, securely fasten all mounting hardware. It is important that all fasteners be properly torqued (see Fig. 3) to assure a safe operating plow. Re-tighten all fasteners after 2 hours of plowing.

2007 TOYOTA TUNDRA W/ Tracks Deuce Installation Manual

download
Remove cargo rail end plugs: At the tailgate push in on the plug lock and at the same time push the end plug out of the track. 2 Next remove tie downs: If tie down are installed remove them from the cargo rail. 3 1 3 2 4 4 Install clamps in cargo rail as shown below: After clamps and tie downs are installed replace the cargo rail end plugs. Leave clamps loose for now. Next repeat steps 1 through 4 for the passenger side clamp installation. 5 Tailgate end Position clamp here Front of box Position tie down here Position clamp here Position clamp here Position tie down here Position clamp here Four clamps per side needed. Continue with step 8 in the main Deuce manual. 2007 TOYOTA TUNDRA W/TRAcks DeUce INsTALLATION INsTRUcTIONs Install Deuce Rail: With the tailgate closed, position the TruXedo rail along the inside edge of the truck box. Compress the rear seal against the tailgate as shown. Tighten clamps against the rail. See step seven for proper clamp height. leave clamps loose for now 7 Tighten clamp assemblies securely on side rails before driving vehicle. ! The TruXedo rail will be positioned at this height. Clamp height is correct at this setting. Next install the front striker bracket: From one end of the front cargo rail remove the plastic insert plug. Next slide the striker bracket assembly into the cargo rail. See step nine for additional information

2007-2008 Toyota Tundra Rear Driveshaft/ Propeller Shaft Clunk/ Thunk Noise Repair Manual

download
Repair Procedure 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition Repair Procedure (Continued) 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing. 3. Test drive and confirm that NO abnormal vibrations or shudders occur while driving, and that the driveshaft clunk/thunk noise is eliminated.

2000-2006 TOYOTA TUNDRA VEHICLE WIRING INFORMATION

download
WIRING INFORMATION: 2000 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door WIRING INFORMATION: 2001 Toyota Tundra WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE/RED OR WHITE Ignition Harness STARTER WIRE GREEN/BLACK Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/RED Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) WHITE/GREEN Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel POWER DOOR UNLOCK (-) RED/YELLOW Wires Can Be Found In A Harness In Both The Driver’s Kick Panel And In The Passenger Kick Panel PARKING LIGHTS (+) GREEN Harness In Drivers Kick Panel HEADLIGHTS (-) GREEN/YELLOW Harness At Steering Column DOOR TRIGGER (-) WHITE/BLUE Harness Coming Into Vehicle From Drivers Door DOME LIGHT SUPERVISION USE DOOR TRIGGER FACTORY ALARM ARM ARMS WITH LOCK FACTORY ALARM DISARM (-) BLUE/BLACK Drivers Door Harness TACHOMETER WIRE BLACK OR BLUE/WHITE Behind Instrument Cluster BRAKE WIRE (+) GREEN/WHITE Harness In Driver’s Kick Panel Or Brake Switch HORN TRIGGER (-) GREEN/RED Harness At Steering Column LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Door LEFT FRONT WINDOW UP GREEN At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/YELLOW At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN RED/GREEN Harness In Driver’s Kick From Driver Doo