Skip to content

2007 honda civic timing belt change interval

You search PDF repair manual about 2007 honda civic timing belt change interval, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Volkswagen New Beetle GL timing belt replacement manual

download
REMOVAL & INSTALLATION NOTE: For 2004, manufacturer does not provide a timing belt replacement interval. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Engine code AEG is stamped into machined pad on front of cylinder block above crankcase breather, near cylinder head mating surface. See Fig. 1 . For all other 2.0L engines, engine code is stamped on transmission mating flange at the rear of the engine. See Fig. 2 . For all engines, code can also be found on the vehicle data plate and on a sticker on the timing belt cover. Fig. 2: Locating Engine Identification Code (AVH, AZG, BDC & BEV) Courtesy of VOLKSWAGEN UNITED STATES, INC. TIMING BELT Removal (AEG, AVH, AZG, BEV & BDC Engine Codes) 1. Remove right hand insulation tray from engine compartment. Remove engine cover. Rotate serpentine belt tensioner clockwise to relieve belt tension. Remove serpentine belt. See Fig. 3 . Lock in place using Mandrel (T10060) or a drift. Fig. 3: Releasing Serpentine Belt Tensioner Courtesy of VOLKSWAGEN UNITED STATES, INC. 2. Remove serpentine belt tensioner assembly. See Fig. 4 . Turn crankshaft to TDC position. See Fig. 5 . Align TDC marks visible in bellhousing access hole. See Fig. 6 . Remove upper timing belt cover. Ensure camshaft sprocket timing mark aligns with mark on rear cover. See Fig. 5 . 3. Support engine from above or below with floor jack to take engine weight off of mounts. Remove coolant reservoir and set aside. On Golf and Jetta, remove power steering reservoir (hoses attached), and set aside. On New Beetle, pull off EVAP hoses at EVAP canister and throttle valve housing. 4. On all models, remove engine mount from timing belt end of engine. See Fig. 7 . Remove crankshaft pulley from crankshaft sprocket. It is NOT necessary to remove center bolt (center bolt is torque-to-yield type that must be replaced if removed). 5. Remove timing belt covers. Remove engine support from front of engine. See Fig. 4

Toyota LandCruiser 4.2TD Timing belt replacement intervals

download
Timing belt replacement intervals The information relating to timing belt replacement intervals is additional to the main purpose of this CD, but is included to provide guidance to garages and for customer advice. Where possible the recommended intervals have been compiled from vehicle manufacturers’ information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully later in this section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. 5. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due. 6. If the belt does fail, have you considered the consequences. If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. 7. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. 8. If in doubt about the condition of the belt – RENEW it. 9. Removal Removal Remove timing belt cover [1]. 1. Turn crankshaft clockwise until timing marks aligned [2]. 2. Ensure timing marks aligned: 1KZ-T/TE: [3]. 3. 4. Remove: Automatic tensioner unit [6]. Tensioner pulley bolt [7]. Tensioner pulley [8]. Timing belt. 5. Installation Installation Check tensioner pulley for smooth operation [8]. Replace if necessary. 1. Remove dust cover. Check tensioner body for leakage or damage [6]. Check pushrod protrusion is 9,0-9,8 mm [9]. 2. Check pushrod does not move when pushed against a firm surface. If pushrod moves: Replace automatic tensioner unit. 3. Slowly compress pushrod into tensioner body until holes aligned. Use press. 4. Retain pushrod with 1,5 mm Allen key through hole in tensioner body [10]. Fit dust cover. 5. Ensure timing marks aligned [2]. 6. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 7. Fit timing belt in anti-clockwise direction, starting at lower sprocket. Ensure belt is taut between sprockets. 8. Fit tensioner pulley [8]. Tighten bolt to 34 Nm [7]. 9. Push tensioner pulley against belt. Install automatic tensioner unit [6]. Tighten bolts evenly to 13 Nm [5]. 10. Remove Allen key from tensioner body to release pushrod. 11. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3] or [4]. 12. If not: Repeat installation and tensioning procedures. 13. Install components in reverse order of removal. 14. Reset timing belt replacement warning lamp as follows: 15. -Runner/Landcruiser: Remove grommet in speedometer housing. Depress switch using a thin screwdriver [11]. 16. Colorado: Remove speedometer housing. Remove screw indicated and insert in alternative location [12]. 17. Amazon: Lamp illuminates at 90,000 miles. Return vehicle to dealer.

Rover Timing belt replacement intervals

download
Apart from the visible condition of the belt, which is explained fully later in this section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. 5. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due. 6. If the belt does fail, have you considered the consequences. If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. 7. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. 8. If in doubt about the condition of the belt – RENEW it. 9.

2001 Honda Prelude Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Manual

download
Removal and Installation REMOVAL NOTE: * Turn the crankshaft pulley so the No. 1 piston is at Top Dead Center (TDC) before removing the belt. * Inspect the water pump after removing the timing belt. * Replace the timing belt and timing balancer belt at 105,000 miles (168,000 km) according to the maintenance schedule (normal conditions/severe conditions). If the vehicle is regularly driven in one or more of the following conditions, replace the timing belt and timing balancer belt at 60,000 miles (U.S.A.) 100,000 km (Canada). * In very high temperatures (over 110°F, 43°C). * In very low temperatures (under -20°F, -29°C). 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio’s preset buttons. 2. Disconnect the battery negative terminal first, then the positive terminal. 3. Remove the wheel well splash shield. 4. Loosen the adjusting bolt, locknut and mounting bolt, then remove the Power Steering (P/S) pump belt. 5. Remove the alternator terminal and connector. 6. Loosen the adjusting bolt, mounting bolt and lock nut, then remove the alternator belt. 7. Remove the side engine mount. NOTE: * Support the engine with a jack before removing the side engine mount and upper bracket assembly is removed. * Make sure to place a cushion between the oil pan and the jack 8. Remove the dipstick and the tube. 9. Remove the cylinder head cover. NOTE: The procedures in steps 10 and 11 are for reusing the timing belt. For replacing the timing belt, skip these procedures and go to step 12. 10. Use an open-end wrench to loosen the maintenance bolt. If it cannot be loosened with an open-end wrench, a box wrench can be used after removing the lock pin. NOTE: Use of a tool should be limited to initial loosening only 11. Unscrew the maintenance bolt by hand until it stops. The auto-tensioner bracket is now fixed. NOTE: * Never use a tool to unscrew the maintenance bolt after initial loosening it. * If the auto-tensioner has been extended and the timing belt cannot be installed, remove the auto-tensioner, compress it and reinstall it. 12. Remove the middle cover. NOTE: Do not use the middle cover to store removed items. 13. Remove the pulley bolt and crankshaft pulley

2007 HONDA CIVIC SI REAR UNDER SPOILER INSTALLATION INSTRUCTIONS

download
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: •Be careful not to damage the rear bumper and body paint finish. •This rear under spoiler kit should be installed only if the ambient air temperature is 60°F (15°C) or above. •To allow the adhesive to “cure,” do not wash the vehicle for 24 hours. 4 Self-tapping screws Template Clip Rubber washer 2 If the vehicle is equipped with a rear inner fender, go to step 7; if not, continue with step 5. 5. Using a drill, drill one 3 mm hole through the lower dimple on the rear bumper on each side. • After drilling, remove any burrs from the edges of the holes with a file. DIMPLED AREA 1. Attach the template to the arched section of the rear bumper. Secure the template with strips of tape. 4. Using a hacksaw blade, cut the rear bumper along the lines you made. • After cutting, remove any burrs from the edges of the cut section. REAR BUMPER Cut out the marked area. TEMPLATE (Remove.) DRILL STOP 2. Mark the rear bumper along the outer edge of the template with a felt-tip pen, and lightly center- punch the four marks on the template. 3. Remove the template. While wearing eye protection, drill a 10 mm hole through each mark you just made. • Using a drill stop on the end of each bit, first drill with a 3 mm drill bit, and finish with a 10 mm drill bit. DRILL (3 mm 10 mm DRILL BIT) CENTER- PUNCH REAR BUMPER FELT-TIP PEN TEMPLATE REAR BUMPER TAPE 10 mm DRILL (3 mm DRILL BIT) MARKS (4) MARKS (4) HACKSAW BLADE