Skip to content

2007 navigator air ride reset

You search PDF repair manual about 2007 navigator air ride reset, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Ford Expedition/Navigator Ride Height Adjustments Manual

download
WARNING: Disconnecting an air line that is connected to the air compressor can cause personal injury or damage to components as high pressure air is vented uncontrolled. 1. Turn the air suspension switch on. 2. Turn the ignition switch to the RUN position. 3. Connect NGS Tester to the data link connector (DLC). 4. Select Air Suspension Control Module under Active Command Mode: ? VENT FRNT to deflate the front down. ? LIFT FRNT to inflate the front up. ? VENT REAR to deflate the rear down. ? LIFT REAR to inflate the rear up. Front Ride Height Resetting — Clear B2140 DTC 1. Turn the ignition key OFF and turn it back to RUN; exit the vehicle, close all doors and allow the system to vent the vehicle down to kneel height (approximately 30 seconds). 2. Connect New Generation STAR (NGS) Tester to the data link connector (DLC). 3. Select the proper vehicle year, model and engine type. 4. Select 4WAS-AIR SUSP/EVO (4×2 and 4×4) module. 5. Select “Parameter Reset Command (Clear Ride Height) under Active Command Modes” menu, trigger through the warning messages and reset (trigger from OFF to ON): ? NGS version 10.0 — “Front” and “Rear.” ? NGS version 11.0+ — “Front CLR.” 6. Back out the torsion bar adjustment bolt (approximately 40 mm from the bolt head to the bottom surface of the torsion bar adjuster). 7. Deflate the front air shocks by using the NGS “Vent Front” command in “Air Suspension Control” menu (should take about 30 seconds), and jounce the front of the vehicle to fully lower the front of the vehicle. 8. Adjust and measure the vehicle ride height; refer to Section 204-01B. 9. NOTE: Do not save rear ride heights. The air suspension control module has precalibrated values already stored. Refer to Rear Ride Height Mechanical Resetting. Select the “Save Calibration Values (Store Ride Height)” NGS command to calibrate the air suspension control module. Trigger through the warning message(s) and save “FRONT” (trigger from OFF to ON).

1997-2001 FORD EXPEDITION ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE

download
SUSPENSION, AIR SUSPENSION DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 RIDE HEIGHT RESET PROCEDURE ELECTRICAL LAMP – AIR SUSPENSION LAMP ILLUMINATED – DIAGNOSTIC TROUBLE CODES (DTC’S) B2140 OR C2140 – RIDE HEIGHT RESET PROCEDURE SERVICE PROCEDURE AIR SUSPENSION DTC’S THAT ARE PRESENT NOTE BEFORE ADDRESSING B2140/C2140. DURING PDI (PRE-DELIVERY INSPECTION) IF WARNING “CK SUSP” LIGHT IS ON, PRIOR TO SENDING WARNING: BEFORE REPLACING ANY AIR TO SERVICE, VERIFY SWITCH IN UPPER RIGHT SUSPENSION COMPONENTS, HOISTING, KICK PANEL IS ON. THIS SWITCH IS TURNED JACKING, OR TOWING, DISCONNECT POWER OFF DURING VEHICLE SHIPMENT TO PREVENT TO THE SYSTEM BY TURNING OFF THE AIR MODULE FROM SEEKING TRIM HEIGHT WHILE SUSPENSION SWITCH LOCATED IN THE RIGHT SECURED DOWN FOR TRANSPORT. KICK PANEL AREA TO PREVENT VEHICLE NOTE DAMAGE OR PERSONAL INJURY. AN INADVERTENT B2140 OR C2140 MAY RAS ONLY – CLEAR 2140 RESULT IF A PARAMETER RESET (CLEAR RIDE HEIGHT) IS SELECTED UNDER NGS ACTIVE NOTE COMMANDS, THEN CANCELLED OUT. EVEN RAS (4X2) EQUIPPED VEHICLES REQUIRE STORING RIDE HEIGHT AND NOTE TOGGLING FRONT TO “ON” TO CLEAR A CK THE AIR SUSPENSION CONTROL MODULE SUSP LIGHT/2140 CODE. THIS ALLOWS THE PART NUMBER IS INTERCHANGEABLE MODULE TO STORE THE VOLTAGE WITH NO BETWEEN THE REAR AIR SUSPENSION (RAS) FRONT HEIGHT SENSOR PRESENT, AND MUST AND 4-WHEEL AIR SUSPENSION (4WAS) BE DONE EVEN WITH CONVENTIONAL (STEEL SYSTEMS, BUT ONCE THE MODULE IS COIL) FRONT SUSPENSION. INSTALLED, THE VEHICLE WILL THEN DETERMINE WHETHER VEHICLE IS 4X2 (RAS)

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

2004-2007 FORD E-150, E-250, E-250, E-350 4.6L / 5.4L ENGINE-SLOW FUEL FILL REPAIR MANUAL

download
ISSUE carbon canister inlet. If there is no free flow Some 2004-2007 E-150 – E-350 vehicles equipped past the CVV, the CVV is failed or frozen with a 4.6L or 5.4L engine and mid-ship fuel tank closed. Replace the CVV. may experience a “Slow to Fill” condition. c. If you have free flow through the CVV and the vent hose, the restriction must be at the ACTION Separator Assembly (Dust Box). Check the Use the Service Procedure to check the canister Canister Separator Assembly for damage, vent tube for a spider web or other obstruction dirt, water or ice contamination and replace before replacing the fuel tank. the Separator Assembly. SERVICE PROCEDURE 2. If the fuel tank is still difficult to fill with the 1. Disconnect the evaporative emission (EVAP) carbon canister disconnected, replace the fuel lines where it connects from the fuel tank to the tank assembly. carbon canister assembly inlet. If the tank can be easily filled, the carbon canister and EVAP PART NUMBER PART NAME lines should be investigated for restriction, 5C2Z-9S327-CA Fuel Vapor Vent continue to Step 1a. If the fuel tank is still 6F1Z-9F945-AA Solenoid Canister Vent difficult to fill with the carbon canister XF2Z-9B328-AA Separator Asy Fuel 6C2Z-9002-AA Tank Asy Fuel disconnected, proceed to Step 2. (Figure 1) F75Z-9F945-CA Solenoid Canister Vent WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part. OPERATION DESCRIPTION TIME MT071501 Use SLTS Operations If Actual Available; Claim AdditionalTime Diagnosis Or Labor Figure 1 – Article 07-15-1 Performed As Actual Time DEALER CODING a. Spider webs and other debris in the vent CONDITION hose 5C2Z-9S327-CA may restrict the hose. BASIC PART NO. CODE Disconnect and blow out vent hose with 9S327 55 shop air or roll a bearing down the hose to remove the debris.

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).