2007 pontiac g5 manual

You search PDF repair manual about 2007 pontiac g5 manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2007 pontiac g5 manual Direct Download speed 5432 Kb/s

  2007 pontiac g5 manual Full Version speed 8172 Kb/s



4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

w584a lincoln, 2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, how to change intake gasket 2007 grandprix, schematic for front brakes on 2005 Buick Rendezvous, 200lolds aleroraditor system, 2007 Chevy Colorado Gas Tank Seal replace, 2007 kia rio service manual, pontiac 2007 g6 remove radiator cover

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 18-02-2012

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

Related Content:

2004 buick rendezvous repair manual, service manual for 2004 audi a6 2 7t quattro, 2003 gmc sierra service repair manual, stepper motor for 2004 chevy trailblazer, free 2003 gmc envoy shop manual, repairing the sunroof in a 04 trailblazer, repair manual mitsubishi diamante, 2004 chevy malibu wiring diagrams for EVAP system, programming 2004 tahoe instrument cluster, 2004 envoy cluster self test

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, 2008 checrolet colorodo emmisions purge valve, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 pilot alternator replacement, how to change the thermostat 2008 ford escape ehow, inhrdvd1000 parts, 2008 saturn outlook transmission pressure solenoid, hummer h3 2008 p0741, 2008 f250 haynes pdf

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

0

Filed Under (More Manuals) by admin on 05-05-2012

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, How to replace shift indicator on 99 f150, replace shifting cable for 2003 GMC Envoy how do you remove the console, replace shifter handle on 2000 malibu, replace shifter cable 2003 rendezvous, cover push button on shifter for chevey 2007 cobalt automatic, buick rendezvous detached shifter, buick rendezvous gear shift cable repair, chevy cobalt shift lock

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, canter 4d 35 interval wiper control relay, p0753 kia rio 2004, wiring diagram for mitsubishi canter ignition, Powertrain Generator 6500 Parts Diagram, bully side ste for jeep instructions, Kia Rio 2001 DTC P0753, 2006 pontiac g6 gt code po753, what is the tcc solenoid on a 2 2 cavalier, p1860 tcc pwm solenoid circuit electrical

Related Content:

w584a lincoln, 2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, how to change intake gasket 2007 grandprix, schematic for front brakes on 2005 Buick Rendezvous, 200lolds aleroraditor system, 2007 Chevy Colorado Gas Tank Seal replace, 2007 kia rio service manual, pontiac 2007 g6 remove radiator cover