Skip to content

2007 pontiac grand prix steering wheel shakes

You search PDF repair manual about 2007 pontiac grand prix steering wheel shakes, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

1997-1998 Buick Regal GS & Pontiac Grand Prix GTP with L67 3.8L V6 Engine Fuel Pump Resistor Service Procedure

download
The following are instructions for removing the fuel pump resistor from its original mounting location on the lower right front body rail as shown in Figure 1, and replacing it with a new fuel pump resistor and cover in new location shown in Figure 2. The new location is on the front of dash sheet metal (3) at the rear of the engine compartment, inboard or to the left of the alternator (4). The passenger or right side windshield wiper arm (5) and stop (6) are called out for reference purposed only. 1. Turn the steering wheel to the full right position. 2. Open the hood and disconnect the negative battery cable. 3. Remove the diagonal brace (1) from over the windshield washer solvent reservoir by removing the two bolts (2) that attach it to the radiator support and the one bolt (3) that attaches it to the strut tower. Refer to Figure 3 4. Remove the two plastic push-in retainers (1) that attach the windshield washer solvent reservoir (2) to the radiator support (3) and the one nut (4) that attaches it to the strut tower (5). Refer to Figure 4. 5. Reposition the reservoir for access to the area rearward of the battery. 6. Raise the vehicle on a hoist. 7. At the right front wheel opening, remove the three screws that attach the inner fender splash shield to the front fascia at the wheel opening and the two screws that attach it to the bottom of the fascia. Refer to Figure 5. 8. Reposition the inner fender splash shield (1) to access the fuel pump resistor (2). Refer to Figure 1 at the beginning of this procedure. 9. Unclip the fuel pump resistor electrical connector from the body and disconnect the connector. 10. Remove the 10mm hex head bolt attaching the fuel pump resistor to the body and discard both the bolt and the resistor.

2001 Subaru Legacy GT Sedan AWD F4-2.5L SOHC Steering and Suspension, Wheel Bearing, Service and Repair Manual

download
1. Remove knuckle. Refer to Steering and Suspension. 2. Using ST1 and ST2, remove hub from rear housing. 3. Remove back plate from rear housing. 4. Using a standard screwdriver, remove outer and inner oil seals. CAUTION: Use new oil seals. 5. Using flat bladed screwdriver, remove snap ring. 6. Using ST1 and ST2, remove bearing by pressing inner race. ST1 927430000 HOUSING STAND ST2 927440000 BEARING REMOVER CAUTION: * Do not remove bearing unless damaged. * Do not re-use bearing after removal. 7. Remove tone wheel bolts and remove tone wheel from hub (only vehicle equipped with ABS). 8. Using ST, press hub bolt out. ST 927080000 HUB STAND. CAUTION: Be careful not to hammer hub bolts. This may deform hub. INSPECTION Check the removed parts for wear and damage. If defective, replace with a new one. CAUTION: * If a bearing is faulty, replace it as the bearing set. * Be sure to replace oil seal at every overhaul. ASSEMBLE 1. Using ST, press new hub bolt into place. CAUTION: * Ensure hub bolt closely contacts hub. * Use a 12 mm (0.47 inch) hole in the ST to prevent hub bolt from tilting during installation.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).