Skip to content

2007 tahoe door latch repair

You search PDF repair manual about 2007 tahoe door latch repair, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.

2004 Toyota Sienna POWER SLIDING DOOR INOPERATIVE Repair Manual

download
Remove Slide Door Window Garnish. A. Fully open the slide door window. B. Remove the glass run. C. Using a screwdriver, disengage the clip and remove the garnish. HINT: Tape the screwdriver tip before use. D. Using the taped screwdriver, disengage the 2 claws and remove the inner weatherstrip from the garnish. Parts Information Repair Procedure Clip POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 3 of 7 2. Remove Side Trim Board Cover Rear. A. Remove the 2 screws. B. Using the taped screwdriver, disengage the 8 claws and remove the cover together with the window control switch. C. Remove the 2 screws and window control switch. 3. Remove Rear Door Trim Board Sub-assembly. A. Remove the screw. B. Using the taped screwdriver, disengage the 9 clips and remove the trim board. HINT: In order to prevent the door panel from being damaged, cover the areas with protective tape as indicated by the arrows in the illustration. 4. Remove Rail End Molding. A. Open the quarter glass. B. Using the taped screwdriver, disengage the clip and 2 claws, and remove the rail end molding. Repair Procedure (Continued) : Claw 1 2 3 4 5 5 4 3 2 1 Protective Tape Protective Tape : Clip : Clip : Claw POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 4 of 7 5. Remove Center Bracket No. 2. A. Remove the 2 bolts and Center Bracket No. 2 together with the tensioner (color: white). B. Remove the tensioner from Center Bracket No. 2. 6. Remove Center Bracket No. 1. A. Remove the 2 bolts and Center Bracket No. 1 together with the tensioner (color: black). B. Remove the tensioner from Center Bracket No. 1. 7. Remove Slide Door Window Assembly LH. A. With Sunshade: Remove the sun shade hook. B. Remove the bolt and window frame. C. Remove the bolt. D. Loosen the nut. E. Push the rear lower window frame in the direction indicated by the arrow in the illustration

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).