Skip to content

2007 yukon p0300

You search PDF repair manual about 2007 yukon p0300, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

2004-2007 FORD E-150, E-250, E-250, E-350 4.6L / 5.4L ENGINE-SLOW FUEL FILL REPAIR MANUAL

download
ISSUE carbon canister inlet. If there is no free flow Some 2004-2007 E-150 – E-350 vehicles equipped past the CVV, the CVV is failed or frozen with a 4.6L or 5.4L engine and mid-ship fuel tank closed. Replace the CVV. may experience a “Slow to Fill” condition. c. If you have free flow through the CVV and the vent hose, the restriction must be at the ACTION Separator Assembly (Dust Box). Check the Use the Service Procedure to check the canister Canister Separator Assembly for damage, vent tube for a spider web or other obstruction dirt, water or ice contamination and replace before replacing the fuel tank. the Separator Assembly. SERVICE PROCEDURE 2. If the fuel tank is still difficult to fill with the 1. Disconnect the evaporative emission (EVAP) carbon canister disconnected, replace the fuel lines where it connects from the fuel tank to the tank assembly. carbon canister assembly inlet. If the tank can be easily filled, the carbon canister and EVAP PART NUMBER PART NAME lines should be investigated for restriction, 5C2Z-9S327-CA Fuel Vapor Vent continue to Step 1a. If the fuel tank is still 6F1Z-9F945-AA Solenoid Canister Vent difficult to fill with the carbon canister XF2Z-9B328-AA Separator Asy Fuel 6C2Z-9002-AA Tank Asy Fuel disconnected, proceed to Step 2. (Figure 1) F75Z-9F945-CA Solenoid Canister Vent WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part. OPERATION DESCRIPTION TIME MT071501 Use SLTS Operations If Actual Available; Claim AdditionalTime Diagnosis Or Labor Figure 1 – Article 07-15-1 Performed As Actual Time DEALER CODING a. Spider webs and other debris in the vent CONDITION hose 5C2Z-9S327-CA may restrict the hose. BASIC PART NO. CODE Disconnect and blow out vent hose with 9S327 55 shop air or roll a bearing down the hose to remove the debris.

2005-2007 Ford F-Super Duty STEERING WHEEL OSCILLATION REPAIR MANUAL

download
This article supersedes TSB 07-5-7 to update the NOTE Parts. SETTING TIRE PRESSURE TO DOOR SPECIFICATION IS ONE OF THE SINGLE MOST ISSUE IMPORTANT MEASURES IN RESOLVING THIS Some 2005-2007 F-Super Duty vehicles may exhibit ISSUE. LOWERING TIRE PRESSURE WILL MAKE steering wheel oscillation (back and forth motion), THIS ISSUE WORSE. immediately following front or rear wheel impacts ROAD TEST (i.e. pavement joints, frost heaves, rough roads, etc.). Steering wheel motion is typically in the range 1. Ask customer what type of road surface and of ± 5 degrees, and typically dampens out in fewer speed generates the steering wheel oscillation. than five oscillations. This condition occurs mostly on F-250/F-350 4X4 vehicles, and is more evident 2. Road test vehicle on similar road surface and on trucks equipped with a gas engine. speed, to gain a feel for the customer’s issue. ACTION 3. If no issues are identified during the road test, do not proceed with the rest of this TSB. Refer to the following Service Procedure to minimize the steering wheel oscillations on impacts, STEERING DAMPER however, there may be some remaining minor INSPECTION/REPLACEMENT AND oscillation which would be considered normal. STEERING/SUSPENSION FASTENER TORQUE CHECK SERVICE PROCEDURE SUMMARY F-250/F-350 4X4 Applications: 1. Set tire pressure and road test vehicle to evaluate vehicle before proceeding with further 1. Remove existing steering damper and frame repairs. If issue is resolved, do not proceed attachment bracket. with the rest of this TSB. 2. Replace steering damper and frame mounting 2. If concern still exists, install a new steering bracket with steering damper and frame damper (frame-mounted bracket and steering bracket. damper assembly on F-250/F-350 4X4 applications only). For F-250/F-350 4X2 and all 3. Attach steering damper to frame bracket and F-450/F-550 applications, inspect damper for torque bolt to 76 lb-ft (103 N•m). leaks and replace if necessary, torque steering 4. Assemble bracket and shock assembly to the and suspension fasteners per Workshop frame with attachment bolt retainer pointing to Manual (WSM). rear of vehicle. Torque frame bracket nuts to 59 3. If concern still exists, check front alignment and lb-ft (80 N•m). reduce front caster. 5. Attach other end of shock to the steering drag 4. Replace redundant control steering wheel (if link and torque to 66 lb-ft (90 N•m). equipped and vehicle built prior to 10/8/2004). 6. Install damper bolt cap to assure a friendly VEHICLE INSPECTION – TIRE PRESSURE surface for the battery cable in case of casual contact. 1. Set tire pressures as indicated on the vehicle label (located on driver’s door label).

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.

2007-2010 Toyota Camry Hybrid Vehicles Potential Floor Mat Interference with Accelerator Pedal

download
The owner notification will commence in early February, approximately one week after your dealership has been notified. This campaign will be launched in phases. • The first phase will include certain 2007 through 2010 model year Camry and Camry Hybrid vehicles equipped with Denso accelerator pedals. These owner letters will be mailed over a period of several weeks. • Additional models, including Camrys equipped with a CTS accelerator pedal will be launched in later phases as the remedy is developed. • Information on additional phases related to Camry (equipped with a CTS accelerator pedal), Avalon, Corolla, Highlander, Matrix, Prius, Tacoma, Tundra and Venza will be provided prior to the launch of these phases. If your dealership is contacted by an owner of a Denso pedal equipped Camry who has not yet received a notification, please verify eligibility by confirming through Dealer Daily/TIS prior to performing repairs . Dealers should perform the repair as outlined in the attached Technical Instructions. 2. Vehicles in Dealer Stock • As required by Federal law, dealers are not to deliver any new vehicles in their inventory, which are involved in a safety recall unless the defect has been remedied. However, because this defect does not exist in vehicles in which the driver’s side floor mat is compatible with the vehicle and properly secured you may continue to sell new vehicles (with Denso pedals) that have not received the full remedy if you assure the driver’s position floor mat is semi-permanently secured or place the front driver’s and passenger’s floor mats in the trunk on any vehicles in stock prior to sale or lease. Vehicle safety recall completion can be verified through TIS. • In order to assure established customers receive priority for the safety recall, we request that this campaign remedy be performed on in-stock Camry and Camry Hybrid vehicles just prior to vehicle delivery where possible. • A VIN list containing vehicles in dealer stock will be provided shortly