Skip to content

2008 chevy silverado steering column diagram with parts list

You search PDF repair manual about 2008 chevy silverado steering column diagram with parts list, if there are search results will appear below. If search results do not exist, please search by others keyword.

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE SERVICE MANUAL

download
Repair Procedure 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. Production Change Information Parts Information Repair Procedure STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 3 of 4 3. Remove the No. 2 steering intermediate shaft assembly. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 7. Install the No. 1 steering column hole cover sub-assembly onto the steering gear with a NEW clamp. Repair Procedure (Continued) B A a No. 2 Steering Intermediate Shaft Intermediate Shaft STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 4 of 4 8. Install the No. 1 steering column hole cover sub-assembly by attaching clip B onto the body and installing the No. 1 hole cover onto the body with clip A. NOTE: Make sure that the lip of the No. 1 hole cover is NOT damaged. 9. Install the No. 2 steering intermediate shaft assembly. A. Align the matchmarks (“a”) on steering intermediate shaft and the steering sliding yoke and temporarily install them with bolt B. Torque: 35 Nm (360 kgfcm, 26 ftlbf) B. Ensure the wheels are straight. C. Install the No. 2 intermediate shaft and the intermediate shaft with bolt A. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 10. Install the column hole cover silencer sheet. A. Install the column hole cover plate with the 2 clips. B. Install the floor carpet. 11. Remove the steering wheel holder from the vehicle. 12. Road test the vehicle to verify the repair and confirm that the steering wheel is centered.

1989 Chevrolet Corvette V8-350 5.7L Steering Column Service and Repair Manual

download
SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined. 2. Place turn signal lever to the right turn position, then remove screw and switch actuator pivot assembly (Nos. 11 and 44 in Fig. 59 ). 3. Remove the screws and the wiring protector (Nos. 10 and 45). 4. Remove turn signal switch, then gently pull wire harness through column housing shroud, column housing and lock housing cover. 5. Reverse procedure to install, noting the following: a. Torque turn signal switch screws (No. 10 in Fig. 59 ) to 27 inch lbs. and torque screw (No. 11) to 18 inch lbs. BUZZER SWITCH ASSEMBLY & STEERING COLUMN LOCK CYLINDER SET

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2003-2007 Accord V6 Power Steering Moans or Whines Repair Manual

download
SYMPTOM A moan or whine is heard when turning the steering wheel when the engine is cold. There may be air bubbles or foam in the power steering reservoir. The noise usually goes away when the engine warms up. PROBABLE CAUSE Air enters the power steering pump through the inlet joint O-ring. CORRECTIVE ACTION Replace the O-ring on the power steering pump inlet joint. PARTS INFORMATION O-ring: P/N 91345-RDA-A01, H/C 8811010 REQUIRED MATERIALS Honda Genuine Power Steering Fluid: P/N 08206-9002, H/C 3747284 (One container repairs about 12 vehicles.) WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 5121B5 Flat Rate Time: 0.3 hour Failed Part: P/N 91345-PAA-A01 H/C 5430681 Defect Code: 07408 Symptom Code: 04201 Template ID: 07-086A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE 1. Remove the bolt holding the inlet joint to the power steering pump housing. 2. Place a shop towel under the inlet joint. 3. Twist the inlet joint back and forth until it is loose, then carefully disconnect the joint and point the hose upward to minimize fluid loss. 4. Remove the inlet joint O-ring. 5. Apply power steering fluid to a new O-ring, and install it on the inlet joint. 6. Install the inlet joint, and torque its bolt to 11 N. m (8 lb-ft). 7. Top off the power steering fluid, if needed. Start the engine, and let it idle. Confirm that the noise is gone and that the system is operating properly

Ford F-Series Column Shift Repairs Manual

download
It’s a simple system. To remove the assembly, start by removing the column shift lever. This is super easy; just use two small punches to depress the two spring-loaded pivot pins on the lever, then pull the lever out. Be aware: the pivot pins and spring will shoot out. Next go under the hood, and undo the two bolts holding the clamp piece just above the steering box. The lower half of the clamp will come free. The upper half is locked to the “shoe” plate under it, and to the steering column, with a round peg cast into it. So you need to pry the shoe up away from the steering column to get the peg clear of the column. Once you do that, you need to pry the upper half of the clamp away from the shoe, so the peg is clear of the shoe. Once it is clear, you can slide the end piece off the shifter tube. Then slide the wave washer and 2-3 lever off. To get the 1-R lever off, you’ll need to pull a steel pin out of the shifter tube. It should just drop out. Then slide the lever, wave washer, and shoe off the tube. Push the shifter tube up to get the clearance needed for the shoe. The shifter tube is a hollow steel tube, with a hole drilled thru it near the bottom. In this hole there is a steel pin (the one just removed). The steel pin engages into slots in the 1-2 and 3-4 levers, to move them. As you can see, there isn’t a lot of wear in my shift levers’ slots. The pin shows some wear, where the tube contacts it. The pin is hardened steel and the shifter tube is mild steel, so the tube will be worse than the pin. The pins are available from Obsolete Ford Parts and others, P/N 01A-7337, only a couple of bucks. Getting the shifter tube out is pretty easy; just drop the column support (remove the bolts to instrument panel and loosen the pinch bolt) down to the floor, and you’ll be able to swing the shift tube to the side to clear the steering wheel, and pull it out. My pin wasn’t that worn, it’s the hole in the tube. The tube is hollow but actually has a steel plug inside it with a hole for the pin. It is pushed inside the tube and then peened in two places thru the outer tube (they punched the outer tube to lock the inner plug). inner plug had gotten loose inside the tube, too. If this is your situation, you could just drill and pin the plug to the outer tube, and get a good improvement. I wanted “like new”, so I took my shifter tube to my favorite machinist (Gene at Noor Mfg. in Albuquerque, a super guy). He made up a whole new lower end for the tube out of 1018 carbon steel. It’s got a spigot on the upper end that was pressed into the remaining tube, welded, then turned down. It is better than new! Look at the difference in the shape of the hole. Price for the work was very reasonable