Skip to content

2008 ford escape service free manual download

You search PDF repair manual about 2008 ford escape service free manual download, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

2001 Ford F-150 Draining-Coalescer/ Pressure Relief-Natural Gas Bi-Fuel System Repair Manual

download
1. Relieve the Bi-fuel system fuel pressure. For additional information, refer to Pressure Relief—Natural Gas Bi-Fuel System. 2. Raise the vehicle on the hoist. For additional information, refer to Section 100-02. 3. NOTE: There is an O-ring attached to the drain plug. The O-ring must be replaced each time the drain plug is removed. Remove the drain plug. 4. Install the drain plug. 5. Lower the vehicle. 6. Pressurize the fuel system. WARNING: It is important that your bi-fuel vehicle be correctly maintained by Ford bi-fuel trained personnel. If a concern occurs, it is important that correctly trained personnel diagnose the cause. If a concern relates to the fuel system, correct part replacement is imperative to keep your vehicle operating at normal performance. Bi-fuel components and gasoline specific components are not interchangeable. If your vehicle is not serviced in accordance with bi-fuel service procedures, damage can occur and your warranty may be invalidated. WARNING: Fuel supply lines are always pressurized. When servicing fuel related components, do not smoke or carry lighted tobacco or an open flame of any type. Flammable mixtures may be present and can ignite, resulting in personal injury. WARNING: The natural gas fuel system is always pressurized to 655 kPa (95 psi) downstream of the fuel pressure regulator and up to 24821 kPa (3,600 psi) upstream of the fuel pressure regulator. Use care when servicing the fuel system or personal injury can occur. WARNING: The natural gas fuel supply manifold is pressurized to 655 kPa (95 psi). Fuel pressure must be relieved prior to any fuel system service. WARNING: The fuel system pressure must be relieved before any component can be removed. The fuel tanks must be evacuated prior to tank removal. Removal of components without pressure relief or tank evacuation can cause natural gas to escape into the air and cause injury or death.

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

FORD, MERCURY, LINCOLN WHITE FLAKES COMING FROM A/ C VENTS SERVICE PROCEDURE

download
FORD: 2007-2009 MKX 2005-2009 Focus 2008-2010 Crown Victoria MERCURY: 2000-2005 Expedition, F-150 2008-2010 Grand Marquis, Mariner Hybrid, 2007-2009 Edge Mariner 2008-2010 Escape Hybrid, Escape LINCOLN: 2008-2010 Town Car SERVICE PROCEDURE MAY BE NECESSARY TO TEMPORARILY START THE ENGINE TO ENABLE MODE DOOR Hazard and Risk Warnings for White Flakes MOVEMENT. WARNING Clean A/C Ducts: MAY CAUSE EYE AND RESPIRATORY TRACT 1. Remove floor duct trim. IRRITATION. PROLONGED REPEATED EXPOSURE MAY CAUSE BONE DAMAGE 2. Using masking tape, connect one end of the (FLUOROSIS) AND HARM TO THE vacuum cleaner hose to the floor duct on driver RESPIRATORY SYSTEM (BASED ON ANIMAL side. DATA). • Avoid inhaling dust. 3. Tape closed all the other floor duct openings. • Avoid contact with eyes. 4. Obtain about two feet (61 cm) of rubber • Store away from acids. vacuum line large enough to fit the end of a small shop air blowgun. Secure the hose to the • Wash thoroughly after handling. end of the blowgun using a worm clamp. • Avoid release to the environment. 5. Close all instrument panel registers. NOTE THE USE OF DUST PROOF GOGGLES, 6. Set temperature setting to full cold. CHEMICAL RESISTANT GLOVES (PVC) AND 7. Place mode in floor / panel. DUST MASK IS RECOMMENDED. 8. Turn on vacuum cleaner