Skip to content

2008 ford focus remove door handle

You search PDF repair manual about 2008 ford focus remove door handle, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.

Ford Focus power window removal And installation Instructions

download
Removing the Door Panel Coverings 1. For ease of installation, do both sides at the same time. 2. Roll the windows to approximately 1/2 open, and so the crank handle is in the Down Position. With either the Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank. 3. Remove the cover plate for the remote-control mirror, which is held in place by 3 spring clips. Remove by gently pulling the front corner of the cover out, and then slide the cover back. 4. Remove the door Pull-handle cover, by inserting a screwdriver into the access hole on the bottom of the handle, and using the screwdriver as a lever, pop off the handle cover. 5. Remove the button covering a retaining screw in the interior door latch backing plate. 6. Remove the 8 Torx™ retaining screws around the perimeter of the door panel, and the single Torx™ retaining screw in the interior door latch. 7. Remove the 2 hex bolts in the door handle. 8. Gently lift the panel upwards, to disengage the window weather-strip molding. 9. Remove the Door Latch Trim Panel, be sure to unplug the Power Lock Switch, and remember how the wire was run. 10. Remove the interior door latch, by gently pulling out on the front corner, which is held in by a plastic compression spring. 11. Remove the Foam Arm Rest bolster, by unclipping the 4 plastic compression clips and the clip fasteners.. 12. Remove the 4 Door Speaker screws, and disconnect the speaker. 13. Gently remove the closed cell Foam Cover from the doorframe, by pulling out, while cutting the rubber cement around the cover. Remove all but the front edge of the cover. This cover tears very easily, so use extreme care. B. Removing the Manual Window Regulator 1. Temporarily re-attach the crank handle, and roll the window so that clamps (6, 7) on window are accessible through the voids in the door frame. 2. Loosen the glass clamp nuts (or bolts). 3. Roll the window all the way up, and lock in place by inserting a screwdriver into the small access hole at the top of the doorframe. 4. Remove the 4 Hex bolts (1, 2, 3) Before removing the last bolt (4), take up the weight of the glass, and remove the last bolt. Gently let the glass rest on the screwdriver. 5. Remove the manual regulator and tracks. C. Installing the Electric Window Regulator 1. Align and install the Hex bolts (1, 2, 3, 4, and nut 5) 2. Loosen the glass clamp nuts (or bolts). 3. Gently let the glass rest in the Clamps. 4. Lightly tighten the glass clamp nuts (or bolts).

FORD, MERCURY, LINCOLN WHITE FLAKES COMING FROM A/ C VENTS SERVICE PROCEDURE

download
FORD: 2007-2009 MKX 2005-2009 Focus 2008-2010 Crown Victoria MERCURY: 2000-2005 Expedition, F-150 2008-2010 Grand Marquis, Mariner Hybrid, 2007-2009 Edge Mariner 2008-2010 Escape Hybrid, Escape LINCOLN: 2008-2010 Town Car SERVICE PROCEDURE MAY BE NECESSARY TO TEMPORARILY START THE ENGINE TO ENABLE MODE DOOR Hazard and Risk Warnings for White Flakes MOVEMENT. WARNING Clean A/C Ducts: MAY CAUSE EYE AND RESPIRATORY TRACT 1. Remove floor duct trim. IRRITATION. PROLONGED REPEATED EXPOSURE MAY CAUSE BONE DAMAGE 2. Using masking tape, connect one end of the (FLUOROSIS) AND HARM TO THE vacuum cleaner hose to the floor duct on driver RESPIRATORY SYSTEM (BASED ON ANIMAL side. DATA). • Avoid inhaling dust. 3. Tape closed all the other floor duct openings. • Avoid contact with eyes. 4. Obtain about two feet (61 cm) of rubber • Store away from acids. vacuum line large enough to fit the end of a small shop air blowgun. Secure the hose to the • Wash thoroughly after handling. end of the blowgun using a worm clamp. • Avoid release to the environment. 5. Close all instrument panel registers. NOTE THE USE OF DUST PROOF GOGGLES, 6. Set temperature setting to full cold. CHEMICAL RESISTANT GLOVES (PVC) AND 7. Place mode in floor / panel. DUST MASK IS RECOMMENDED. 8. Turn on vacuum cleaner

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

2003 HONDA CIVIC Door Panel Removal And Installation Manual

download
2003 CIVIC – Door Panel Removal/Installation Special Tools Required *KTC trim tool set SOJATP2014 *Trim pad remover, Snap-on A 177A or equivalent, commercially available 2-door NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. If applicable, remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C). 2. Remove the inner handle (A). Take care not to scratch the door panel. 3. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model). -1 Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover. -2 Remove the screws. -3 Pull the inner handle forward and out half-way to release the hook (E). -4 Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver’s side for some models). – 1 Using a trim tool, pry the cap (C), then remove the screw (D) 4. Remove the screws (H) securing the door panel. 5. Remove the mirror mount cover. 6. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it. 7. Install the door panel in the reverse order of removal, and note these items: *Replace any damaged clips. *Make sure the connectors are plugged in properly, and the rod is connected properly. *Make sure the window and power door locks operate properly. *If applicable, install the regulator handle so it points forward and up at a 45 º angle with the glass fully closed