Skip to content

2008 kia rondo manual

You search PDF repair manual about 2008 kia rondo manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2007-2008 Toyota Tundra Rear Driveshaft/ Propeller Shaft Clunk/ Thunk Noise Repair Manual

download
Repair Procedure 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition Repair Procedure (Continued) 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing. 3. Test drive and confirm that NO abnormal vibrations or shudders occur while driving, and that the driveshaft clunk/thunk noise is eliminated.

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

2003 HONDA CIVIC Door Panel Removal And Installation Manual

download
2003 CIVIC – Door Panel Removal/Installation Special Tools Required *KTC trim tool set SOJATP2014 *Trim pad remover, Snap-on A 177A or equivalent, commercially available 2-door NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. If applicable, remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C). 2. Remove the inner handle (A). Take care not to scratch the door panel. 3. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model). -1 Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover. -2 Remove the screws. -3 Pull the inner handle forward and out half-way to release the hook (E). -4 Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver’s side for some models). – 1 Using a trim tool, pry the cap (C), then remove the screw (D) 4. Remove the screws (H) securing the door panel. 5. Remove the mirror mount cover. 6. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it. 7. Install the door panel in the reverse order of removal, and note these items: *Replace any damaged clips. *Make sure the connectors are plugged in properly, and the rod is connected properly. *Make sure the window and power door locks operate properly. *If applicable, install the regulator handle so it points forward and up at a 45 º angle with the glass fully closed

Jaguar Electronic Parking Brake Diagnostic Aid/ Repair Manual

download
INITIAL VISUAL INSPECTION 1. Place the vehicle on a suitable lift. 2. Visually inspect the parking brake cable installation, parking brake caliper levers and general condition of the brakes. • Ensure the caliper levers are returning fully to their stops. • Confirm the cable routing is correct • Confirm that the cable is securely fixed at all abutment points and is free to move within the C-clip. • Where cable routing goes over the top of the stabilizer bar drop links, confirm that the stabilizer bar rubber deflector blocks are fitted, and that the brake cables have not been getting trapped behind the stabilizer bar drop links (look for tell-tale marks on the links and/or cables). NOTE: Global Technical Reference (GTR) lookup sequence is as follows: GTR Home > NAS > Model > Service Information > Model Year > Workshop Manual > 2: Chassis — Section 206: Brake System NOTE: Refer to the correct section by reference to VIN and based on whether the vehicle is fitted with high performance brakes or not. 3. Rectify any obvious faults. 4. If no obvious faults are found or further guidance is needed to rectify faults, please proceed to the next stage of this bulletin. Refer to GTR Sections 206-05 (parking Brake and Actuation) and GTR Section 206-04 (Rear Disc Brake). 5. If any faults were found and rectified, it will be necessary to re-calibrate the parking brake after rectification. See ‘Parking Brake Calibration’ procedure. PREPARE THE PARKING BRAKE FOR DETAILED INSPECTION CAUTION: Jaguar IDS DVD 111 or later and Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during diagnosis. 1. Install the Midtronics PSC-550 Vehicle Power Supply to the vehicle. 2. Connect the IDS to the vehicle and begin a new diagnostic session by entering the correct VIN for the current vehicle. 3. Follow the IDS prompts to read the vehicle configuration. 4. Select ‘YES’ when prompted ‘Do you wish to read diagnostic trouble codes?’. 5. Follow all on-screen instructions to complete this task. 6. Select ‘Vehicle Configuration’ tab when the ‘Content Model’ is displayed. 7. Select ‘Electronic Parking Brake’. 8. Select ‘Release to Service Position’ (S-TYPE/XJ) or ‘Parking Brake Unjam Procedure’(XK) ‘. CAUTION: When using the special service tool, take care to operate in the ‘release’ direction. Actuator motor damage may result if the tool is operated in the ‘apply’ direction for any length of time). 9. If the parking brake will not release using IDS, use the special service tool to fully release the parking brake. Refer to GTR Section ‘Parking Brake Cable Tension Release’ (in Section 206-05) for details of using the special service tool.

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.